Discovery 2 Internetworking Module 5 JEOPARDY John Celum

RouterModesWANEncapsulationWANServicesRouterBasicsRouterCommands RouterModesWANEncapsulationWANServicesRouterBasicsRouterCommands Acronyms Boot Commands Modes & Modes & More Commands Switching Up Grab Bag Grab Bag ► ► ► F i n a l J e o p a r d y ◄ ◄ ◄

POST Question Acronyms 100 A: What is Power On Self Test ?

Question A: What is Command Line Interface? CLI Acronyms

Question A: What is Security Device Manager? SDM Acronyms 300

Question A: What is Channel Service Unit/Data Service Unit? CSU/DSU Acronyms 400

Question A: What is High-Level Data Link Control? HDLC Acronyms 500

Question A: What is the POST (Power-On Self Test)? This is performed during the first stage of the router bootup process. Boot

Question A: What is flash? By default the IOS is loaded from this type of memory. Boot 200

Question A: What is the IOS (Internetwork Operating System)? This software (not the program) is located and loaded once the POST is completed. Boot 300

Question A: What is a NVRAM? By default, the IOS will search for a config file in this location. Boot 400

Question A: What is setup mode? The router will enter this mode if a config file is not found. Boot 500

Question A: What is hostname? This command will allow configure a unique name to a device. COMMANDS 100

This global configuration command ensures that all passwords are encrypted.. Question A: What is service password-encryption? COMMANDS 200

Enter the command when traffic with an unknown destination network is forwarded using a defined router interface. Question A: What is ip route s0/0/0? COMMANDS 300

This command will save a running config file in RAM to NVRAM. Question A: What is copy run start? COMMANDS 400

This command will restore a config file on a TFTP server to RAM. Question A: What is copy tftp run? COMMANDS 500

Question A: What is the privilege EXEC mode? This mode will allow commands to be entered that can alter the operation of the device. Modes & Commands 100

Question A: What is user EXEC mode? Commands in this mode are limited to troubleshooting using some show commands and the ping and traceroute utilities. Modes & Commands 200

Question A: What is the terminal history size or history size? This command will change the number of command lines the system records during a session. Modes & Commands 300

Question A: What is the Up Arrow or Ctrl-P? Press this key to recall the most recent command in the history buffer. Modes & Commands 400

Question A: What is show cdp neighbors (detail)? This command displays the information that a Cisco device collects from its directly connected Cisco neighbors. Modes & Commands 500

Question A: What is the Data Link Layer (Layer 2)? Switches operate at this OSI Layer. Switching Up 100

Question A: What is the Autonegotiation Mode? This mode is used to detect the speed and the duplex of the other device. Switching Up 200

Question A: What is Full Duplex? Switching Up 300 This type of duplex mode allows a device to double the throughput by being able to send and receive data simultaneously.

Question A: What is Excessive Collisions (degraded communication)? If the switch port and the connected device are not set to the same duplex mode this will occur. Switching Up 400

Question A: What is interface vlan 1? What is ip address ? List the two commands to set the configuration for vlan 1. Switching Up 500

Question A: What is CDP? This protocol (or tool) is used to gather information about another directly connected Cisco device. GRAB BAG 100

Question A: What is clockrate? When connecting two routers through a serial link, this needs to be pre-configured to change one router to a DCE device. GRAB BAG 200

Question A: What is Point-to-Point? This type of serial link uses a dedicated circuit, fixed bandwidth, and a leased line. An example is a T1 link. GRAB BAG 300

Question A: What is Packet Switched? This type of serial link uses a virtual circuit with many customers sharing the network. An example is Frame Relay. GRAB BAG 400

Question A: What is a TFTP server? A config file is not located in NVRAM. Name the next location where the IOS will search for a config file. GRAB BAG 500

Question A: What is sticky port security? Name the type of port security that will learn about MAC addresses dynamically, store them in the address table, and save the address to the running configuration. Final Jeopardy