Exercise: SIR MODEL (Infected individuals do not move, they stay at home) What is the effect of diffusion? How is the behavior affected by the diffusion coefficient D? What if you have two ‘nests’ of infection?

create a math Model  Spatial for BOX geometry. 1.Copy – Paste the Constants, VolumeVariable and Functions. Add diffusionRate as constant. 2.Cut Initial concentration for infected population. We want to set infected population in a particular place. So we will declare it as Function. 3. We have no Flux BC. 4. Infected people do not move, so no diffusion for Infectected population, i.e. ODE. File->open  mathmodel  satarupa  SIR_NEW_MODEL Save this.

Part-1

Part-2

Healthy people move arround and if they come near infected people, who are in the middle, they get sick !! What happens to Healthy Population: Time plot Line plot S_init=9.0,D= 1.0

Infected population stays at the middle, see how the concentration changes as you increase the time. Line plot, t=.3 Time plot Line plot, t= 10

Recovered Population: Time plot Line plot

Now consider two nests of infection- that is infection in two places: Save this SIR model with a new name to modify it. Only change  Function I_init ((((x-5)^2 + y^2) < 1 ) || (((x-5)^2 + (y-10)^2) < 1 )) *0.2 ; It specifies two two places of infected population with the concentration 0.2 That‘s all !!!

Susceptible (D=1): Line plot Time plot

Infected Time plot Line plot

Recovered:

When diffusion rate =0 If healthy people dont move. Nothing happens outside the infected region Infection becomes epidemic in the infected region Recovered

Fitzhugh-Nagumo system with voltage (ions) spreading along the axon

Create 2D analytic geometry. Set size x=1, Y= 0.5, origin at (0.0). Save it with a name.

1.Copy the constants from the old F-N model (ODE model) and paste, cut Constant V_init, because V is now a sptial variable, i.e. a Function 2. Constant V_diffusionRate ; 3. Copy & paste VolumeVariable and Function.Add new function for V_init. New conditions for our new system: Go file  new  math Model  Spatial  click the geometry you just created file  open  math Model  satarupa  FHN_model (ode model) Save this.

We will set PDE and ODE here— CompartmentSubDomain subVolume1 { Priority 0 BoundaryXm Flux BoundaryXp Flux PdeEquation V { BoundaryXm 0.0; BoundaryXp 0.0; Rate J1; Diffusion V_diffusionRate; Initial V_init; } OdeEquation C { RateJ2; Initial C_init; } Click Apply changes. We have 1 ODE for C

The code looks like -

Click equation viewer -- Close this window and click simulation

Run simulation for t=100, I=0, 0.05, 0.2 can you increase parameter I and get periodic firing?

For I=0.0V at t=0.0C at t=0.0 Time plot CTime plot V

Time plot for V with I= 0.05 Time plot for V with I= 0.2 Time plot for C with I= 0.2Time plot for C with I= 0.05

Time plot for I=0.2, t= 1000 sec V C

Reaction-Diffusion system of the activator-inhibitor type that appears to account for many important types of pattern formation and morphogenesis observed inpattern formationmorphogenesis development.

The development of a higher organism out of a single fertilised egg is one of the most fascinating aspects of biology. A central question is how the cells, which carry identical genetic code, become different from each other. Spontaneous pattern formation in initially almost homogeneous systems is also commonpattern formation in inorganic systems. Large sand dunes are formed despite the fact that the wind permanently redistributes the sand. Sharply contoured and branching river systems (which are in fact quite similar to the branching patterns of a nerve) are formed due to erosion despite the fact that the rain falls more or lessnerve homogeneously over the ground Pattern Formation

When activator spreads much more slowly than the inhibitor, periodically spaced peaks of activator evolve: Exercise 3: on a 2D domain, would you have stripes or spots? Model equations: In my model I have taken e=e, delta=d

For this model we will take retangular geometry. File  Open  Geometry  Satarupa  rectangle save it. File  New  MathModel  Spatial  click the geometry you just saved. Constants, VolumeVariables and Functions

PDEs :

Click Equation viewer to see the equations: Run simulation for t=10, and use line tool to see kymograph results.

For e=.9,d=5, D=1.0, t=10 a For e=.9,d=15, D=1.0, t=10 i

Stripes and other patterns can be produced by reaction diffusion mechanism in 2D domain under variety of initial conditions and chemical interactions. Change initial conditions and different constant parameters for various pattern. For e=.9,d=15, D=1.0, t=10 Rectangualr geometry: ai

Exercise (Fisher equation): Animals or bacteria grow until the local environment cannot handle the population and then spread by diffusion. The result is the invasion and colonization. Mathematically, you see the traveling wave solution. How does it look in 2D? How does the wave speed depend on the value of parameter D?

For this model we will take retangular geometry. File  Open  Geometry  Satarupa  rectangle save it. File  New  MathModel  Spatial  click the geometry you just saved.

Now we have to declare two Functions. 1st Function is simple: Function J P*(1-P) ; Second Function  initial concentration of P Function P_init (1.0 / (1.0 + exp((2.0 * k * ( x))))) ;

The code looks like---

Run simulation for t=20, and use line tool to see kymograph results. t=0 t=2 t=5.7t=14.2

See the kymograph: