Electronic Diagrams Chapter 18

2 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Objectives Identify common component symbols on an electronic schematic diagram Draw a schematic diagram using standardized symbols Draw connecting and crossover paths

3 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Objectives (cont.) Identify interrupted and uninterrupted lines Designate terminals and numerical values of components

4 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Types of Electronic Diagrams The following are types of diagrams defined in ANSI Y : Functional block diagram Single line diagram Schematic diagram or circuit diagram Connection or wiring diagram Interconnection diagram

5 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Functional Block Diagram

6 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Single Line Diagram

7 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Schematic Diagram

8 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Connection Diagram

9 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Standard Symbols Symbols should conform to an internationally or nationally approved standard Symbols should be drawn roughly 1.5 times the size of those shown in the IEEE 315A standard

10 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Standard Symbols Switches and relays should be shown in the “normal” position with no operating force or applied energy

11 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Abbreviations Abbreviations on electrical diagrams should conform to ANSI/ASME Y1.1

12 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Grouping Parts Indicate grouped components using dashed lines to enclose them in a “box”

13 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Arrangement of Symbols Arrange the various parts and symbols to balance blank areas and lines Provide sufficient blank spaces adjacent to symbols to allow for reference designations and notes

14 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Signal Path Arrange schematic and single-line diagrams so that signal or transmission path from input to output proceeds from left to right and from top to bottom when possible

15 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Connections and Crossovers Connecting lines for conductors are typically drawn horizontally or vertically to minimize bends and crossovers

16 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Interrupted Paths Interrupted paths may be used to simplify a diagram

17 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Terminals Terminal circles need not be shown unless they are needed for clarification

18 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Color Coding Terminals or leads are frequently identified by colors or symbols which should be indicated on the diagram

19 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Division of Parts For clarity, draw sections of multi- element parts separately in a schematic Indicate subdivisions with suffix letters

20 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Electron Tube Pin Identification Electron tubes are generally not used in new designs but are still common in high-power amplifiers

21 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Reference Designations It is essential to identify each separately replaceable part with appropriate combinations of letters and numbers Portions not separately replaceable are frequently identified

22 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Numerical Values Along with reference designations, the following numerical values should also be shown: Resistance Capacitance Inductance

23 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Other Information The following information may also be included on schematic diagrams: Functional identification DC resistance of transformer windings or coils Critical input or output impedance values Voltage or current wave shapes at selected points

24 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Other Information (cont.) Wiring requirements for critical ground points, shielding, pairing, etc. Power or voltage ratings of parts Identification of operational controls or circuit functions

25 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Integrated Circuits An integrated circuit is a semiconductor wafer or chip

26 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Printed Circuits Printed circuit boards are widely used and replace hand-wiring methods

27 Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson Education, Upper Saddle River, NJ All Rights Reserved. Computer Graphics CAD greatly simplifies the process of producing printed circuit artwork CAD component layout programs allow you to create the best possible parts placement