Clean water Start and end times of two reaction intervals Specify domain’s starting fluid composition on the Initial pane.

Slides:

Advertisements

Similar presentations

6.i. Modelling environmental processes: kinetic and equilibrium (quasi-thermodynamic) modelling 6(i)

Advertisements

Simulation lasts 30 years Aquifer is 70% Quartz Specify domain’s starting fluid composition on the Initial pane Initial fluid in equilibrium with Quartz.

K d, Freundlich, and Langmuir isotherms. File → New → Sorbing Surfaces → Kd Pull aqueous species from a thermo dataset Enter a unique identifier for the.

Properties of Aquifers

Ground-Water Flow and Solute Transport for the PHAST Simulator Ken Kipp and David Parkhurst.

Enter your fluid composition on the Basis pane. SpecE8 figures concentrations of aqueous and sorbed species, mineral saturation, and gas fugacity. Go to.

Transport Calculations n Advection Dispersion n Reaction n.

Conservative and Reactive Solutes Conservative do not react with soil / groundwater Chloride is a good example Sorbed onto mineral grains as well as organic.

General form of the ADE: sink/source term Chemical sink/source term.

Introduction to GW contamination and

Subsurface Hydrology Unsaturated Zone Hydrology Groundwater Hydrology (Hydrogeology )

Advanced GIS Using ESRI ArcGIS 9.3 Arc ToolBox 4 (Spatial Analyst 2)

CE 510 Hazardous Waste Engineering

Specify flow rate on the Domain pane. GWB will use Darcy’s law to calculate discharge from the viscosity, permeability, and driving force. You can set.

BIOPLUME II Introduction to Solution Methods and Model Mechanics.

Solute (and Suspension) Transport in Porous Media

Isothermal Reactor Design – Part 2

Partitioning of pollutants

X1t models reactive transport in groundwater flows in one linear or radial coordinate. Set initial fluid composition and mass of sorbing mineral Fe(OH)

Minerals and water ーPHREEQC programsー

Variably Saturated Flow and Transport: Sorbing Solute.

Specify domain’s starting fluid temperature on the Initial pane Porewater temperature is 40 °C.

Left-drag to detach panes. Transfer your data between GWB apps. Right-click and hold any pane header (Basis, Results, Initial, Inlet, Inject) then drag.

19 Basics of Mass Transport

Initial chemical composition and temperature can vary across the domain. Click on a “+” button to enter heterogeneity data for any field variable: ● enter.

Constructing student knowledge of mass transport through interpretation of field data x Jodi Ryder Central Michigan University vs x.

Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

FLOW THROUGH GRANULAR BEDS AND PACKED COLUMN

Final Project I. Calibration Drawdown Prediction Particle Tracking

(Z&B) Steps in Transport Modeling Calibration step (calibrate flow & transport model) Adjust parameter values Design conceptual model Assess uncertainty.

Porewater temperature is 40°C Specify domain’s starting fluid temperature on the Initial pane.

Surface complexation retards Pb ++ transport relative to nonreactive tracer Br −. Use Xtplot to display the concentration of several species along the.

Our purpose of well studies Compute the decline in the water level, or drawdown, around a pumping well whose hydraulic properties are known. Determine.

Variable inlet chemistry. Inlet fluid “contaminated” enters the domain from t = 0 to 2 years Inlet fluid “flush” enters the domain from t = 2 to 10 years.

Pulse of Benzene contaminated water is attenuated by biodegradation. X1t models reactive transport in groundwater flows in one linear, radial, or spherical.

Groundwater movement Objective To be able to calculate the hydraulic conductivity of a sample given measurements from a permeameter To be able to evaluate.

CONTAMINANT TRANSPORT MECHANISMS

Decouple reaction between carbonate and acetate, carbonate and methane, and sulfate and sulfide. Config → Redox Couples… Default setting: all redox reactions.

Clean water Specify starting fluid composition on the Initial pane.

Project 1. Proposal. Describe the problem you propose to analyze. Include Background: describe the problem you intend to analyze, give motivation for.

Specify coordinate system on the Domain pane.

Specify kinetic rate laws for mineral precipitation and dissolution (and other reaction types) on the Reactants pane. Use Arrhenius equation to calculate.

Enter your fluid composition on the Basis pane

Project 1. Proposal. Describe the problem you propose to analyze. Include Background: describe the problem you intend to analyze, give motivation for.

Advanced Contaminant-Transport Techniques

Set the simulation’s duration

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Set the initial fluid composition on the Basis pane.

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

X position (m) I s o t p i c m n C , d a y Bulk fluid CO (aq)

The Intervals pane sets the total duration of the simulation.

The Initial fluid has negligible Pb2+ everywhere but the central node

General form of the ADE:

Determining Hydraulic Conductivity

Specify domain’s starting fluid composition on the Initial pane

Default setting: all redox reactions are coupled.

React traces reaction paths involving fluids, minerals, gases, and microbes.

Transport Modeling in Groundwater

Groundwater vocabulary

Anisotropy – Key ideas Effective conductivity that represents aggregate effect of flow through a layered system Effective conductivity is different parallel.

Config → Dual Porosity… Run → Go

Determine the storage coefficient

Unit: Contaminant Transport in Groundwater

Chapter 4 Boundaries.

Some fluid components (mmol/kg)

Swap sorbing mineral into the basis

Transport Modeling in Groundwater

Groundwater Flow Example

Presentation transcript:

Clean water Start and end times of two reaction intervals Specify domain’s starting fluid composition on the Initial pane

Inlet fluid carries pulse of Pb ++ and Br − into the domain Inlet fluid enters the domain from t = 0 to 2 years The Br − acts as a tracer in our model.

Inlet 2 fluid enters the domain from t = 2 to 10 years Clean rinse water: negligible Pb ++ and Br − in the second inlet fluid

Specify domain size, gridding, and flow rate on the Domain pane. Domain is 1 km long, divided into 400 nodal blocks Set specific discharge or head drop Set flowrate for 1st and 2nd reaction intervals

Set various mass transport properties on the Medium pane. Used to calculate coefficient of hydrodynamic dispersion. Porosity affects groundwater velocity.

Kd describes distribution coefficient between Pb ++ and aquifer sediments. Br − does not sorb. Run → Go traces the model File → Open → Sorbing Surfaces… You can add any number of Kd, Freundlich, or Langmuir isotherms. You can also account for ion exchange or surface complexation using the two layer model.

Sorption retards Pb ++ transport relative to nonreactive tracer Br −.