Background on Composite Property Estimation and Measurement

Slides:



Advertisements
Similar presentations
Structural scales and types of analysis in composite materials
Advertisements

Fibre Volume Fraction and Laminate Thickness
Mechanics of Composite Materials
Earthquake Seismology: The stress tensor Equation of motion
PH0101 UNIT 1 LECTURE 1 Elasticity and Plasticity Stress and Strain
Composites Design and Analysis Stress-Strain Relationship Prof Zaffar M. Khan Institute of Space Technology Islamabad.
Microstructure Analysis of Geomaterials: Directional Distribution Eyad Masad Department of Civil Engineering Texas A&M University International Workshop.
Micromechanics Macromechanics Fibers Lamina Laminate Structure Matrix.
Micromechanics Macromechanics Fibers Lamina Laminate Structure Matrix.
Read Chapter 1 Basic Elasticity - Equilibrium Equations
Some Ideas Behind Finite Element Analysis
ES 246 Project: Effective Properties of Planar Composites under Plastic Deformation.
Elastic Properties and Anisotropy of Elastic Behavior.
Theory of Seismic waves
Constitutive Relations in Solids Elasticity
APPLIED MECHANICS Lecture 10 Slovak University of Technology
M. A. Farjoo.  The stiffness can be defined by appropriate stress – strain relations.  The components of any engineering constant can be expressed in.
Lab 6: Torsion test (AISI 1018 Steel, cold drawn )
ECIV 520 A Structural Analysis II
Rheology Different materials deform differently under the same state of stress. The material response to a stress is known as rheology. Ideal materials.
Mechanics of Materials – MAE 243 (Section 002) Spring 2008 Dr. Konstantinos A. Sierros.
Finite Element Method in Geotechnical Engineering
Elements of Thermodynamics Indispensable link between seismology and mineral physics.
Assist.Prof.Dr. Ahmet Erklig
CH3 MICROMECHANICS Assist.Prof.Dr. Ahmet Erklig. Ultimate Strengths of a Unidirectional Lamina.
MACROMECHANICS Ahmet Erkliğ.
Physics. Properties of Matter Session Session Objectives.
Mechanics of Materials II
Lecture # 10 Composites Learning Objectives:
Engineering Equations for Strength and Modulus of Particulate Reinforced Composite Materials M.E – Reinforced Composite Materials Lecture 3 – Part.
Tensile Strength of Continuous Fiber-Reinforced Lamina
1 TENSORS/ 3-D STRESS STATE. 2 Tensors Tensors are specified in the following manner: –A zero-rank tensor is specified by a sole component, independent.
Rules of Mixture for Elastic Properties
ME 520 Fundamentals of Finite Element Analysis
Constitutive modeling of viscoelastic behavior of CNT/Polymer composites K. Yazdchi 1, M. Salehi 2 1- Multi scale Mechanics (MSM), Faculty of Engineering.
Elastic Properties of Solids, Part III Topics Discussed in Kittel, Ch. 3, pages Another Lecture Found on the Internet!
School of Civil EngineeringSpring 2007 CE 595: Finite Elements in Elasticity Instructors: Amit Varma, Ph.D. Timothy M. Whalen, Ph.D.
Defining sign of stress tensor Kittel’s Fig. 15 may be confusing about sign of T xx (which he calls X x ) Stress tensor component T xx is defined as the.
Chapter 2 Stress and Strain -- Axial Loading
Chapter 3 Micromechanical Analysis of a Lamina Elastic Moduli Dr. Autar Kaw Department of Mechanical Engineering University of South Florida, Tampa, FL.
Chapter 4 Material Behavior – Linear Elastic Solids
Poisson’s Ratio For a slender bar subjected to axial loading:
Slide 1AV Dyskin, Geomechanics Group. UWA. Australia Mechanics of Earth Crust with Fractal Structure by Arcady Dyskin University of Western Australia.
Bin Wen and Nicholas Zabaras
MODERN APPROACHES IN PROPERTY ANALYSIS OF POLYCRYSTALLINE TEXTURED MEDIA IN GEO- AND MATERIAL SCIENCE BY NEUTRON DIFFRACTION DATA Victor B. Yakovlev National.
Poisson’s Ratio For a slender bar subjected to axial loading:
EML 4230 Introduction to Composite Materials
Subject: Composite Materials Science and Engineering Subject code:
Constitutive models Part 1 Background and terminology Elasticity.
STRESS-STRAIN RELATIONSHIP
1 Probability and Materials: from Nano- to Macro Scale A Workshop Sponsored by the John s Hopkins University and the NSF CMS Division January
Lecture 12. Mechanical Properties. Engineering Stress < True Stress True StressTrue Strain.
MATSE 259 Spring 2007, C. Muhlstein© C. Muhlstein, 2007 The contents of this lecture are protected under U.S. copyright law and should not be duplicated.
To understand this cartoon, you have to be a physicist, but you must also understand a little about baseball! Elastic Properties of Solids Topics Discussed.
Composite materials At least two different materials put together.
Expectations after this section
Bone Mechanics Bone is a hard connective tissue Forms rigid skeleton
Pendahuluan Material Komposit
ANSYS Basic Concepts for ANSYS Structural Analysis
Topic 5: Bone Mechanics Bone is a hard connective tissue
Continuum Mechanics (MTH487)
Poisson’s Ratio For a slender bar subjected to axial loading:
Composite Materials Chapter 10. Micromechanics of Composites
Mechanics of Biomaterials
15 unknowns.
Poisson’s Ratio For a slender bar subjected to axial loading:
Elastic Properties and Anisotropy of Elastic Behavior
Elastic Properties of Solids, Part III Topics Discussed in Kittel, Ch
Concepts of stress and strain
Poisson’s Ratio For a slender bar subjected to axial loading:
Presentation transcript:

Background on Composite Property Estimation and Measurement

Effective Properties of Particulate Composites Concepts from Elasticity Theory Statistical Homogeneity, Representative Volume Element, Composite Material “Effective” Stress-Strain Relations Particulate composite effective moduli Unidirectional composite effective moduli Lamina constitutive relations Lamina off-axis constitutive relations 2

Orthotropic Material s-e Relations Engineering materials having orthotropic properties are finding increased application in the design of structural systems. An orthotropic material is completely defined by nine independent elastic constants. The most common elastic constants are the following: Elastic moduli E1, E2, E3, in three orthogonal directions Poisson’s ratios, 12, for transverse strain in the j-directions due to stress in the i-direction Shear moduli, G12, G23, G31 in the 1-2, 2-3, and 3-1 planes, respectively The inverse of the elastic matrix which is called the compliance matrix, S, is then given by 3

Orthotropic Material s-e Relations The compliance matrix is symmetric so that the following symmetry relations must hold The nonzero stiffness coefficients, Cij, are found by inverting the compliance matrix (10.17) and are where 4

TRANSVERSELY ISOTROPIC MATERIALS x2-x3 plane is isotropic – all properties transverse to x1 axis are same E1 = EL E2 = E3 = ET G12 = G13 = GL G23 = GT n21 = n31 = nTL n12 = n13 = nLT n23 = n32 = nTT 5

TRANSVERSELY ISOTROPIC MATERIALS SINCE T.I. PROPERTIES ARE NOT DIRECTIONALLY DEPENDENT, ALSO, AS WITH GENERAL ORTHOTROPIC MATERIALS, 7 INDEPENDENT THERMOELASTIC CONSTANTS: 2 E’S, 1or2 G’S, 2or1 n’s, 2 a’s AN APPROXIMATION: MOST TRANSVERSELY-ISOTROPIC COMPOSITES HAVE GL~GT 6

Anisotropic material properties: calculation using phase (particulate and matrix) properties 7

Effective Composite Properties Statistical Homogeneity: to calculate effective properties, it is first necessary to introduce a representative volume element (RVE), which must be large compared to typical phase region dimensions (i.e., reinforcement diameters and spacing) RVE must be large enough so that average stress in RVE is unchanged as size increases: 8

Effective Composite Properties Effective properties of a composite material define relations between averages of field variables s and e Cijkl* and Sijkl* are reciprocals of one another Overbars denote RVE averages 9

Particulate Reinforced Composite Moduli Provided dispersion of particulate reinforcement is uniform, and provided orientation of non-spherical particulates is random, stress-strain relations of such composite materials will be effectively isotropic Two independent elastic moduli For convenience, these are selected to be the bulk modulus (K) and the shear modulus (G) All other elastic constants can be defined in terms of K and G 10

Particulate Reinforced Composite Moduli Effective elastic constants of particulate reinforced composites are obtained using multi-phase material solutions from elasticity theory Exact solutions are possible only in the case of spherical particles Approximate (bounding theory) results are used for other cases, such as non-spherical particles Example of a lower bound result is Arbitrary Phase Geometry (APG) lower bound on G* vi = volume fraction of inclusion; vm = volume fraction of matrix 11

Results of Bounding Theorems for Particulate Reinforced Composite Materials G* = effective shear modulus of particulate reinforced composite Best lower bound is from Arbitrary Phase Geometry (APG) bound Best upper bound is from Composite Spheres Assemblage (CSA) bound 12