RIPPING, CROSSCUTTING, CUTTING ANGLES, COMPOUND ANGLES, CUTTING DADO’S AND CUTTING RABBET’S.

Slides:

Advertisements

Similar presentations

Radial Arm Saws • Table Saws • Miter Saws • Frame-and-Trim Saws

Advertisements

PLANNING FACE GRAIN JOINTING EDGES STRAIGHT AND SMOOTH CUTTING RABBIT JOINTS CUTTING CHAMPFERS AND BEVELS.

Power Tools Safety. Portable Circular Saws Stock must be well supported in such a way that the kerf will not close and bind the blade.. Thin materials.

Sliding Compound Miter Saw Safety & Use. Safety Rules Always keep hands at least 4” away from blade Always allow the blade to get to speed before cutting.

Table Saw Safety Training

Stationary Power Tool Safety

Band Saw Safety Rules. Safety Rule #1 Keep all guards in place. Keep all guards in place.

Manufacturing Technology Safety: Band Saw. Safety Rule #1  Keep all guards in place.

Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 15 Woodworking with Power Machines.

Woodworking with Power

Production Tools in Technology

Radial Arm Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person.

Drill Press Instructions and Safety.. Safety Glasses Safety Glasses MUST be worn in the wood shop at ALL TIMES.

Building the Footstool P R O J E C T O V E R V I E W.

TABLE SAW SAFETY Pre-TEST. Ripping stock to width is accomplished by using a guide called the fence. TRUE.

Miter Saw Safety Description:

Grimsby Secondary Construction Technology Equipment Safety.

POWER SAWS Two main categories of power saws: Portable & Stationary. Work is fed into a stationary saw. Saws that are fed into the work are portable. Smaller.

Proper Use of Agricultural Mechanics Power Tools

Copyright © Texas Education Agency, All rights reserved. Flexible Manufacturing Basic Safety 1.

Table Saw Safety & Operation The Table Saw is one of the most versatile pieces of equipment but must be operated safely and correctly. Follow these safety.

BAND SAW SAFETY Pre-TEST. You should not support the stock with your hands on each side of the blade as a cut is being made. FALSE – support the stock.

Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.

Power Tool Safety Guidelines for Construction Trades Students.

Safety Rules for 9 th Grade Shop Radial Arm Saw: Safety Rules Never cut a board that is less than 12 inches long. Always pull the saw using the handle;

Table Saw Safety An Introduction. Always wear personal protective equipment like safety glasses, or dust masks when operating the table saw. This applies.

Machine Safety Presentations Safety Unit. Presentations Tool Safety Machine Safety Teaching yourselves and peers.

Table Saw. Blade Guards Anti-Kickback Device Power Switch.

Harding High School Technology Lab Safety Power Machine Review Mr. Pottkotter & Mr. Robinson.

Table Saw Safety.

Power Machine Safety Harding High School Mr. Robinson/ Mr. Pottkotter.

Jointer. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.

COMPOUND MITER SAW SAFETY

RADIAL ARM SAW. History Unlike most types of woodworking machinery, the radial arm saw has a clear genesis: it was invented by Raymond De Walt of Bridgeton,

Table Saw (Circular Saw)

Band Saw Safety in the Lab. Common Techniques Parts of the Band Saw.

DAY 6 Table Saw Question Review Wood Shop Shop Glue up Demo.

Square Plant Stand. TOOL: Radial Arm Saw NEXT STEP: Surface Planer RESULTS: Rough size pieces for 4 Legs. 33” long PROJECT Square Plant Stand PART Legs.

Shop Safety Safety in the shop is the MOST important aspect.

October 1, 2007Derek Casper. October 1, 2007Derek Casper There’s a new table saw invented which is called the saw stop. It features a revolutionary safety.

Scroll Saw Operation and Safety

Machine Safety Review. Areas for safety review Identify this machine.

Machine Safety Rules. Miter Saw Instructor must be present when you are using this machine. Keep wood flat and against fence Hold down wood Do not remove.

Skilled Trades / Res. Cons’t. Table Saw Mr. Mark Shortall / Technology Department.

Bandsaw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.

Final Review.  Fusion -- Heating two pieces of metal to their melting point and allowing them to flow together.  Base Metal -- Metal to be welded 

SAFETY RULES AND PROCEDURES FOR POWER TOOLS INDEPENDENCE MIDDLE SCHOOL TECHNOLOGY EDUCATION DR. HURD 2010.

Parts, Safety and Operation. 1. Fence 2. Table 3. Miter Adjusting Lever 4. Miter Scale 5. Turn Base 6. Vertical Hold-Down Vise 7. Arm 8. Slide.

March TABLE SAW SAFETY The table saw is, by far, the highest risk piece of equipment in the woodshop – when you consider how much the table saw is.

Rip vs. Cross-Cut Rip – cuts along the wood grain

Band Saw Safety Rules.

Flexible Manufacturing

BAND SAW CHAPTER 24.

Proper Use of Agricultural Mechanics Power Tools

Power Tool Safety Don’t operate a machine until:

Band Saw Safety Rules.

Anti-Kickback Fingers

Band Saw Safety Rules.

The size of the Band Saw is determined by the diameter of the wheels;

Band Saw Safety Rules.

Jointer Welcome to a tutorial video discussing how to safely use and operate the jointer.

Radial Arm Saw.

Band Saw Safety Rules.

Band Saw Safety Rules.

Dust Extractor The dust extractor should always be turned on before cutting any piece of wood. It can be turned on using the green button on the switchboard.

Sliding Compound Miter Saw

TABLE SAW SAFETY The table saw is, by far, the highest risk piece of equipment in the woodshop – when you consider how much the table saw is used coupled.

Presentation transcript:

RIPPING, CROSSCUTTING, CUTTING ANGLES, COMPOUND ANGLES, CUTTING DADO’S AND CUTTING RABBET’S

USE THE KICKBACK GUARD, SAW GUARD AND A PUSH STICK OR ANY OTHER SAFETY DEVICES FOR ALL OPERATIONS. ALWAYS STOP THE MACHINE BEFORE MAKING ANY ADJUSTMENTS. KEEP THE FLOOR AROUND THE SAW FREE SCRAPS, SO THERE IS NO DANGER OF SLIPPING. WHEN USING THE TABLE SAW CONCENTRATE 100% ON WHAT YOU ARE DOING. WOOD TO BE SAWED MUST HAVE ONE JOINTED EDGE AND HELD AGAINST ONE OF THE FENCES. NEVER TRY TO SAW (FREEHAND) THAT IS, WITHOUT HOLDING THE WOOD AGAINST A FENCE. THE SAW BLADE MUST NOT RISE ABOVE THE BLADE MORE THAN 1/8”. DO NOT ALLOW ANOTHER PERSON TO STAND BEHIND THE SAW, IN LINE WITH THE BLADE DO NOT REACH OVER THE BLADE. HAVE A HELPER ASSIST YOU IN CATCHING YOUR WOOD. USE A CLEARANCE BLOCK WHEN CROSSCUTTING SHORT PIECES. NEVER USE THE RIPPING FENCE AS A STOP WHEN CROSSCUTTING. THIS MAY CAUSE A KICKBACK. AFTER TURNING OFF THE SAW REMAIN AT THE MACHINE UNTIL THE BLADE COMES TO A COMPLETE STOP.

E D G E R A B B I T