P1 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 A mass (weight 20N) is suspended by two wires as shown in the figure: relevant distances.

Slides:



Advertisements
Similar presentations
Part- I {Conic Sections}
Advertisements

Questionnaire on Water Consumption in Sweden P1 From what source do you consume water from most frequently ? P2 Is your home connected to the public system.
Teach A Level Maths Bodies in Equilibrium.
Chapter 8A. Work A PowerPoint Presentation by
Adding and Subtracting Polynomials 7-6
ENGR-1100 Introduction to Engineering Analysis
Like Terms, I Add Them Adding Polynomials. Like terms are terms that contain the same variables, with corresponding variables having the same power. Example:
December 4 AP Physics.
P1 RJM 13/03/08For IEEE Colloquium Control Education, Sheffield © Dr Richard Mitchell 2008 Modeling Project at Reading Dr Richard Mitchell and Dr Will.
Minimum Weight Plastic Design For Steel-Frame Structures EN 131 Project By James Mahoney.
Find the tension T in each cable and the magnitude and direction of the force exerted on the strut by the pivot in each of the arrangements in Fig. below.
Splines IV – B-spline Curves
Construction of a regular pentagon Dr Andrew French Const. Pent. p1 of 10. A.French 2012.
C O N I C S E C T I O N S Part 3: The Ellipse.
Distributed Computing 9. Sorting - a lower bound on bit complexity Shmuel Zaks ©
A. S. Morse Yale University University of Minnesota June 4, 2014 TexPoint fonts used in EMF. Read the TexPoint manual before you delete this box.: A A.
 The force that act on the object are balanced in all direction.  The force cancel each other, so that the resultant force or net force is zero.  Newton’s.
1 Chapter Four Newton's Laws. 2  In this chapter we will consider Newton's three laws of motion.  There is one consistent word in these three laws and.
Normal Force Force on an object perpendicular to the surface (Fn)
Writing Force Equations. Writing force equations 1.Draw a FBD to identify all forces and the directions they act 2.Write an equation to sum up the horizontal.
More Forces Lecturer: Professor Stephen T. Thornton
Forces in Two Dimensions Trig Review: Sin, Cos, and Tan only work in a RIGHT TRIANGLE. SOHCAHTOA,an ancient Hawaiian word.
VECTORS AND THE GEOMETRY OF SPACE Vectors VECTORS AND THE GEOMETRY OF SPACE In this section, we will learn about: Vectors and their applications.
Friction Acts in direction of plane (i.e. up or down the table) Factors affecting friction Limiting friction F lim =  R.
Inclined Plane Problems
NEWTON’S FIRST LAW Definition- An object at rest will remain at rest, or if it is moving, it will continue to move with constant velocity, unless acted.
Chapter 6 Vectors 6.1 General Information and Geometric uses A vector is a quantity that has both magnitude and direction. tip tail Two vectors are equivalent.
Gaussian Elimination, Rank and Cramer
Geometric and Algebraic.  A vector is a quantity that has both magnitude and direction.  We use an arrow to represent a vector.  The length of the.
Vectors and the Geometry of Space 9. Vectors 9.2.
The Nature of Friction “don’t let it rub you the wrong way”
Work, Energy & Power AP Physics 1. There are many different TYPES of Energy. Energy is expressed in JOULES (J) Energy can be expressed more specifically.
Review for Dynamics test Page 1Page 1 - Net force with weight Page 2Page 2 - Friction on a level surface Page 3 Page 3 - Inclined Plane Page 4 Page 4.
FORCES IN SPACE (Noncoplanar System of Forces)
1© Manhattan Press (H.K.) Ltd. 1.5 Static equilibrium of a rigid body.
Applications & Examples of Newton’s Laws. Forces are VECTORS!! Newton’s 2 nd Law: ∑F = ma ∑F = VECTOR SUM of all forces on mass m  Need VECTOR addition.
P1 RJM 06/08/02EG1C2 Engineering Maths: Matrix Algebra 1 EG1C2 Engineering Maths : Matrix Algebra Dr Richard Mitchell, Department of Cybernetics AimDescribe.
P1 RJM 18/02/03EG1C2 Engineering Maths: Matrix Algebra Revision 7 (a) Figure Q7-1 shows an electronic circuit with two batteries and three resistors. The.
Chapter 6 Practice Problems. Equations Sin θ = opposite side hypotenuse Cos θ = adjacent side hypotenuse Tan θ = opposite side adjacent side.
Period 2 Question 1.
P1 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 6 Matrix Algebra - Tutorial 6 32.Find the eigenvalues and eigenvectors of the following.
Chapter 5 Two Dimensional Forces Equilibrium An object either at rest or moving with a constant velocity is said to be in equilibrium The net force acting.
Resolving Forces Into Vector Components Physics Montwood High School R
Statics: Force Equilibrium The condition of equilibrium How to solve Example Whiteboards (Demo: Force scales, masses)
P1 RJM 07/08/02EG1C2 Engineering Maths: Matrix Algebra 3 Determinants and Inverses Consider the weight suspended by wires problem: One (poor) way is to.
Mechanics 1 Friction.
Cars travelling on a banked curve. For a level (flat) curved road all of the centripetal force, acting on vehicles, must be provided by friction.
1. The following diagram shows a system of forces acting on a particle in a plane. A third force is added so that the particle rests in equilibrium. Find.
Poll The angle of the hill is 30 . If the ball is moving up the hill, what is its acceleration, if the +x direction is defined to be “to the right, down.
An 7.3-kg object rests on the floor of an elevator which is accelerating downward at a rate of 1.0 m/s 2. What is the magnitude of the force the object.
Three blocks of masses M 1 =2 kg, M 2 =4 kg, and M 3 =6 kg are connected by strings on a frictionless inclined plane of 60 o, as shown in the figure below.
Inclined Plane Problems. Axes for Inclined Planes X axis is parallel to the inclined plane Y axis is perpendicular to the inclined plane Friction force.
The Mechanics of Forces
Vectors and the Geometry
Inclined Planes, Tension, & Multiple Objects Clicker Review
Equations and Inequalities involving Absolute Value
Key Areas covered Resolving the weight of an object on a slope into a component acting down the slope and a component acting normal to the slope. Systems.
Algebra 1 Section 5.2 Write equations of lines given slope and a point
Statics of rigid bodies
Blocks 1 and 2 of masses ml and m2, respectively, are connected by a light string, as shown. These blocks are further connected to a block of mass M by.
Aim: How do we explain motion along an inclined plane?
1. A ball of mass m is suspended from two strings of unequal length as shown above. The magnitudes of the tensions T1 and T2 in the strings must satisfy.
Motion on Inclined Planes
TUTORIAL 6.
In practice we are given an angle (generally from the horizontal or vertical) and we use trigonometry 20N 20 sin 300N cos 300N.
THE CORRECTED VERSION FOR THE HANGING MASS PROBLEM
Equilibrium For Coplanar Forces
Gravitational Force and Inclined Planes
Forces Connected Bodies.
Presentation transcript:

p1 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 A mass (weight 20N) is suspended by two wires as shown in the figure: relevant distances are also marked. T 1 and T 2 are the tensions in the wires. By resolving in the horizontal and vertical directions, write down equations involving T 1 and T 2. Express these as one matrix equation. Matrix Algebra - Tutorial 1 1.

p2 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 For the circuit given above, write down three equations in terms of the three currents shown, and then express these in one matrix equation. 2.

p3 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 A 40N weight mass is on a plane whose coefficient of friction is 0.5, and the forces affecting the mass are shown. Friction and the force F parallel to the plane keep the mass in place. R is the force applied by the mass normal to the plane, so the frictional force is 0.5R. The force up the plane is thus F + 0.5R. By resolving forces horizontally and vertically, write down equations relating F and R and then express these equations as one matrix equation. Note: cos(36.87) = 0.8 and sin(36.87) =

p4 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 4. A mass (weight 2N) is suspended by three wires, as shown above. Let the tensions in the wires be T 1, T 2 and T 3. The components of the tensions in the x, y and z directions are For T *T 1, 0.5*T 1 and -0.1*T 1. For T 2 0, 0.7*T 2 and 0.5*T 2. For T 3 0.8*T 3, -0.7*T 3 and -0.1*T 3. Express this system as a matrix equation.

p5 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 5. Evaluate the following if they can be evaluated - if not explain why. a) A + Bb) A * B c) A + Ed) A - 2*B e) 5 * Cf) C * D g) A * Eh) F * C i) D T * C j) D * Ak) B T * A T l) B * A m) F T * C

p6 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 6. Show that, even though C is not the zero matrix, A.C = B.C and yet A does not equal B. 7.Show that A.A T is a symmetrix matrix.

p7 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 Answers

p8 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1 c) Not the same size. h) Incompatible sizes.

p9 RJM 16/10/02EG1C2 Engineering Maths: Matrix Algebra Tutorial 1