FAC calibration for wheel balancer Editor: Song Zhi CHECKED ： Li Chuanhong Version ： A1001 Date ： 2010.10.21 The factory calibration program can be suitable.

Slides:

Advertisements

Similar presentations

Parallel parking.

Advertisements

Adding a Crystal Report to M3 This presentation will assist you in adding a custom Crystal report into Millennium 3.

Using the Avanti Tabletop Centrifuge As demonstrated by Joe Toney.

Off Highway Truck Wheel Retracting Chock Holder. Purpose To have wheel chocks readily available on each truck To have wheel chocks readily available on.

（ 1 ） PROCEDURE FOR FLAT HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE.

Medium shot, background music “Today I am going to show you how to change your rear tire when you get a flat out on the road. We are going to remove the.

4Identifying Leakage Source (Mech/ Elec) 4Mechanical Air Leak- Down 4Mechanical Air Leak- Up 4Electronic Drift- Up/ Down 4Load Cell Operation 4Understanding.

Parallel Parking Identify 1½ Car Lengths of Available Space

Disabled Platform Access There are two designated parking bays immediately outside the front of the main college building. Disabled access both into the.

PART-2. Access the functions as described. Accessing functions. To change the accessing password, follow the steps below. Use the NEXT key to select:

Unknown risk vehicle stop

Bluetooth Remote Control

Chapter 8 STARTING, STEERING, STOPPING

HANDLE JOG MODE The HAAS Control Series PRESS THREE TIMES TO GET TO THIS PAGE (Continued on next slide) Note: SLIDE LEGEND ACTIONS INSTRUCTIONS KEYS.

The Energy Conservatory

Plotting coordinates into your TI 84 Plus Calculator.

Vibration Technical Bulletin. Table of Contents Appearance Inspector Stamp.

EQUATIONS This presentation accompanies the worksheet: “Simple equations” available at:

Chapter 6. Steering Use comfortable, balanced hands DRIVING FORWARD... WHICH WAY DO YOU TURN THE WHEEL TO GO RIGHT? Right GO LEFT? Left.

Performing Basic Vehicle Maneuvers.  Steering Straight Forward-The steering adjustments you need to make to drive in straight lines are small but critical.

Selenium Web Test Tool Training Using Ruby Language Discover the automating power of Selenium Kavin School Kavin School Presents: Presented by: Kangeyan.

Selenium Web Test Tool Training Using Ruby Language Discover the automating power of Selenium Kavin School Kavin School Presents: Presented by: Kangeyan.

STEP 1: Determining the exact image width STEP 1: Determining the exact image width Position of X-ray Filter Position of X-ray Filter STEP 5: Crop Extra.

Chapter Seven: Presentation Software (MS PowerPoint 2007) Author(s): Ahmed Dalalah, Ahmed Abusalameh, Mohammad AlZoubi & Khaled Dajani (Prepared By: Ahmed.

Chapter 3 Basic Vehicle Control

Optical Manufacturing Solutions 1 FOLLOW THE DIRECTIONS BELOW AFTER INSTALLING A NEW CUTTER BODY WITH POLISHING WHEELS INTO THE 7E TYPE MACHINES. IT IS.

Office 2003 Advanced Concepts and Techniques M i c r o s o f t Access Project 5 Enhancing Forms with OLE Fields, Hyperlinks, and Subforms.

Scout Pro Training Introducing the Scout Pro Portable Balance: 7 Models From 200g x 0.01g to 6000g x 1g 5 Application Modes Optional USB or RS232 Interface.

CAD3D Project. SketchUp - Project Create a new SketchUp project called InitialsXX where the XX are your first and last initial. Use the Rectangle tool.

Instructors begin using McGraw-Hill’s Homework Manager by creating a unique class Web site in the system. The Class Homepage becomes the entry point for.

Basic Vehicle Control Where are things located. Instrument Panel Speedometer Odometer Tachometer Fuel Gage.

How to use Touch Screen SeneS Technology. Co, Ltd.

FAC CALIBRATE OF THE MEASURE SCALE Power on——mount the ready 14” tire——input the parameters of the tire （ dis/br/dia ） ——press the program key ——it will.

1 Virginland Technology Co., Ltd. Source Tagging Purchase Process.

How to install Office 2007  Step 1: Insert the Microsoft Office 2007 Enterprise CD. If the Setup Wizard does not automatically begin, then click Start.

Microsoft ® PowerPoint ® 2010 Training PowerPoint tips and tricks.

Selenium Web Test Tool Training Discover The Automating Power Of Selenium Author : Girija Prasad Panda Alcatel-Lucent.

Change in your CAD Project File - it happens all the time in robotics.

When & How to Order Supplies. Before ordering supplies, it is important to check supply levels to see what supplies will be needed. Press and hold the.

*** CONFIDENTIAL *** © Toshiba Corporation 2008 Confidential Printing Reports.

1. Enter service mode and scroll to the Calibrate menu option What is Rider Calibration? This feature enables a rider to calibrate the Watt sensor before.

Performing Basic Vehicle Maneuvers. Steering  Use a comfortable, balanced hand position(9 and 3 o-clock position) to keep safe from the air bags. –Over.

TIRE BALANCING Tire Balancing WEAR YOUR SAFTY GLASSES!!!

Vroom,Vroom.  Insert the key into the ignition. It should be located behind the right side of the steering wheel  make sure that the shifter is in.

FAC calibration for wheel balancer Editor: Song Zhi C HECKED ： Li Chuanhong Version ： A1001 Date ： The factory calibration program can be suitable.

THE FOLLOWING SLIDES SHOW SAFETY HAZARDS & POOR WORK PRACTICES.

Quick Record (Simple Song) 1. Press the Record Button 2. Press the (F2) Soft Button to select Quick Record 3.Press the Play Button to start the recording.

Wheel Throwing: A motor skill Who doesn’t like playing with mud? Get dirty and have fun!

CTCT PCS900 v1.10 Quick Start Guide Phil Jackson Training Manager March 2010.

FAC calibration for wheel balancer Editor: Song Zhi C HECKED ： Li Chuanhong Version ： A1001 Date ： The factory calibration program can be suitable.

By the Brown Team Module 2. Driver Preparation Procedures Always check for small children and pets, fluid leaks, tire inflation, obvious physical damage,

Unit 9 The trial balance. To navigate around the unit Press the enter button to move onto the next screen. If you need to move back press the backspace.

An Introduction to Programming with C++1 An Introduction to Control Structures Tutorial 1.

Clay Throwing on the Wheel

BRIGHT TECHNOLOGY CO., LTD Intelligent and environment protection

Powertap User Guide.

TIRE BALANCING.

An introduction to programming Created by Dr. Randy Pausch

Pictures and cars.

Way to Recognize the Wheel Alignment Slot of your Car

مفاهیم بهره وري.

WHEEL BALANCING TOPIC 4.

Alabama Driver Manual Chapter 3

Running a Java Program using Blue Jay.

Level 1 Module 2 Lesson 5 AXS Machines.

Publisher Tutorial.

Presentation transcript:

FAC calibration for wheel balancer Editor: Song Zhi CHECKED ： Li Chuanhong Version ： A1001 Date ： The factory calibration program can be suitable for CB448 and CB460B.

FAC calibration for truck wheel balancer Step 1: Power on the machine and install the 14” car tire on the wheel balancer then input the three parameter （ dis/br/dia ） of the tire. Step 2: Calibrate ----car tire DYN balance model Press the ENTER button, There shows “P” on the left display. Preparing work 100g lead22.5” tire 14” tire

FAC calibration for truck wheel balancer Press “Dis+” to enter “ SET –UP” Press “ENTER” to enter “ IN–TES ” Then press “ENTER” to enter “ POS ” “ XX ”

FAC calibration for truck wheel balancer Rotate the tire by hand slowly and the POS value will change. When there’s 110, Press key. Then continue to pull the tire and when there’s 120, press the key.

FAC calibration for truck wheel balancer It will show the display “ ADD ”--” 0 ” like the following picture, then press the ” START” key. There will show “ ADD ”-- ” 100 ” like the left picture after the tire stopped to rotate.

FAC calibration for truck wheel balancer Pull the tire till the indicator light all shine, then put the 100g weight on the rim outside 12 o’clock place. Then press “START” key to run the machine for calibration.

FAC calibration for truck wheel balancer There will show “100”--”ADD” on the display like below picture after the tire stopped to rotate. Then remove the 100g weight. Pull the tire till the inside indicator light all shine then put the 100g weight on the rim inside 12 o’clock place.

FAC calibration for truck wheel balancer Press the key to run machine and there will show “SAU”—”dAt ” on the display when the tire stops. The Factory Self-calibration for car tire is finished. Because the CB460X and CB448X have two balance model ( for car tire and for truck tire), it must be calibrated under car tire balance model firstly and then calibrate under truck tire balance model to ensure the precise balance. The method of calibration under truck tire balance model is the same as under the car tire balance model.