HHG Seeding of Mode-Locked Free Electron Lasers

Slides:



Advertisements
Similar presentations
Femtosecond lasers István Robel
Advertisements

DL/RAL Joint Accelerator Workshop 21 st January 2009 Free Electron Laser Studies David Dunning MaRS ASTeC STFC Daresbury Laboratory.
Lecture 6. New FEL Schemes and Challenges X-Ray Free Electron Lasers Igor Zagorodnov Deutsches Elektronen Synchrotron TU Darmstadt, Fachbereich
Lecture 4. High-gain FELs X-Ray Free Electron Lasers Igor Zagorodnov Deutsches Elektronen Synchrotron TU Darmstadt, Fachbereich May 2014.
Lecture 3. Low-gain and high-gain FELs X-Ray Free Electron Lasers Igor Zagorodnov Deutsches Elektronen Synchrotron TU Darmstadt, Fachbereich May.
X-ray Free Electron lasers Zhirong Huang. Lecture Outline XFEL basics XFEL basics XFEL projects and R&D areas XFEL projects and R&D areas Questions and.
Schemes for generation of attosecond pulses in X-ray FELs E.L. Saldin, E.A. Schneidmiller, M.V. Yurkov The potential for the development of XFEL beyond.
Soft X-ray Self-Seeding
Ultrafast Experiments Hao Hu The University of Tennessee Department of Physics and Astronomy, Knoxville Course: Advanced Solid State Physics II (Spring.
Optical sources Lecture 5.
Approaches for the generation of femtosecond x-ray pulses Zhirong Huang (SLAC)
2004 CLEO/IQEC, San Francisco, May Optical properties of the output of a high-gain, self-amplified free- electron laser Yuelin Li Advanced Photon.
A. Zholents, July 28, 2004 Timing Controls Using Enhanced SASE Technique *) A. Zholents or *) towards absolute synchronization between “visible” pump and.
Absorption and emission processes
UCLA The X-ray Free-electron Laser: Exploring Matter at the angstrom- femtosecond Space and Time Scales C. Pellegrini UCLA/SLAC 2C. Pellegrini, August.
Ultrafast Experiments Hangwen Guo Solid State II Department of Physics & Astronomy, The University of Tennessee.
Chapter 9 Electromagnetic Waves. 9.2 ELECTROMAGNETIC WAVES.
High Harmonic Generation in Gases Muhammed Sayrac Texas A&M University.
FEL Beam Dynami cs FEL Beam Dynamics T. Limberg FEL driver linac operation with very short electron bunches.
The impact of undulators in an ERL Jim Clarke ASTeC, STFC Daresbury Laboratory FLS 2012, March 2012.
W.S. Graves1 Seeding for Fully Coherent Beams William S. Graves MIT-Bates Presented at MIT x-ray laser user program review July 1, 2003.
Alvaro Sanchez Gonzalez Prof. Jon Marangos Prof. Jim Clarke
+ SwissFEL Introduction to Free Electron Lasers Bolko Beutner, Sven Reiche
A. Doyuran, L. DiMauro, W. Graves, R. Heese, E. D. Johnson, S. Krinsky, H. Loos, J.B. Murphy, G. Rakowsky, J. Rose, T. Shaftan, B. Sheehy, Y. Shen, J.
Free Electron Lasers (I)
Travelling Wave Tube For Broadband amplifier helix TWTs (proposed by Pierce and others in 1946 ) are widely used For High average power purposes the.
Nonlinear Optics in Plasmas. What is relativistic self-guiding? Ponderomotive self-channeling resulting from expulsion of electrons on axis Relativistic.
Beam Dynamics and FEL Simulations for FLASH Igor Zagorodnov and Martin Dohlus Beam Dynamics Meeting, DESY.
SFLASH  SASE interference setup & optics rough estimation 1d estimation 3d estimation summary.
Enhancing the Macroscopic Yield of Narrow-Band High-Order Harmonic Generation by Fano Resonances Muhammed Sayrac Phys-689 Texas A&M University 4/30/2015.
Optimization of Compact X-ray Free-electron Lasers Sven Reiche May 27 th 2011.
A bunch compressor design and several X-band FELs Yipeng Sun, ARD/SLAC , LCLS-II meeting.
A U.S. Department of Energy Office of Science Laboratory Operated by The University of Chicago Office of Science U.S. Department of Energy Containing a.
X-RAY LIGHT SOURCE BY INVERSE COMPTON SCATTERING OF CSR FLS Mar. 6 Miho Shimada High Energy Research Accelerator Organization, KEK.
Max Cornacchia, SLAC LCLS Project Overview BESAC, Feb , 2001 LCLS Project Overview What is the LCLS ? Transition from 3 rd generation light sources.
External Seeding Approaches: S2E studies for LCLS-II Gregg Penn, LBNL CBP Erik Hemsing, SLAC August 7, 2014.
M. Hosaka a, M. Katoh b, C. Szwaj c, H. Zen b M. Adachi b, S. Bielawski c, C. Evain c M. Le Parquier c, Y. Takashima a,Y. Tanikawa b Y. Taira b, N. Yamamoto.
Basic Energy Sciences Advisory Committee MeetingLCLS February 26, 2001 J. Hastings Brookhaven National Laboratory LCLS Scientific Program X-Ray Laser Physics:
Operated by Los Alamos National Security, LLC for NNSA Dynamics of modulated beams Operated by Los Alamos National Security, LLC, for the U.S. Department.
Harmonic lasing in the LCLS-II (a work in progress…) G. Marcus, et al. 03/11/2014.
The Next Generation Light Source Test Facility at Daresbury Jim Clarke ASTeC, STFC Daresbury Laboratory Ultra Bright Electron Sources Workshop, Daresbury,
UCLA Claudio Pellegrini UCLA Department of Physics and Astronomy X-ray Free-electron Lasers Ultra-fast Dynamic Imaging of Matter II Ischia, Italy, 4/30-5/3/
FEL Spectral Measurements at LCLS J. Welch FEL2011, Shanghai China, Aug. 25 THOB5.
J. Corlett. June 16, 2006 A Future Light Source for LBNL Facility Vision and R&D plan John Corlett ALS Scientific Advisory Committee Meeting June 16, 2006.
Prebunching electron beam and its smearing due to ISR-induced energy diffusion Nikolai Yampolsky Los Alamos National Laboratory Fermilab; February 24,
What did we learn from TTF1 FEL? P. Castro (DESY).
E. Schneidmiller and M. Yurkov FEL Seminar, DESY April 26, 2016 Reverse undulator tapering for polarization control at X-ray FELs.
Emittance-exchange-based high harmonic generation scheme for FEL JIANG Bocheng SINAP 2012 July 18~20 Lanzhou China 2012 Deflecting/Crabbing Cavity Applications.
Simulations of X-ray production for different undulator options 19 th of March 2015 Juergen Pfingstner.
Free Electron Laser Studies
Seeding in the presence of microbunching
Eduard Prat / Sven Reiche :: Paul Scherrer Institute
Beam dynamics for an X-band LINAC driving a 1 keV FEL
Free Electron Sources of CoherentRadiation: FREE ELECTRON LASERS
Tunable Electron Bunch Train Generation at Tsinghua University
EEHG 101: The Basics of Echo-7
Review of Application to SASE-FELs
Free Electron Lasers (FEL’s)
Principle of Mode Locking
F. Villa Laboratori Nazionali di Frascati - LNF On behalf of Sparc_lab
Two-bunch self-seeding for narrow-bandwidth hard x-ray FELs
SASE FEL PULSE DURATION ANALYSIS FROM SPECTRAL CORRELATION FUNCTION
High harmonic generation in a large-volume capillary for seeding of free-electron lasers Siew Jean Goh.
Longitudinal-to-transverse mapping and emittance transfer
Longitudinal-to-transverse mapping and emittance transfer
Gain Computation Sven Reiche, UCLA April 24, 2002
LCLS FEL Parameters Heinz-Dieter Nuhn, SLAC / SSRL April 23, 2002
Achieving Required Peak Spectral Brightness Relative Performance for Four Undulator Technologies Neil Thompson WP5 – 20/03/19.
Introduction to Free Electron Lasers Zhirong Huang
Enhanced Self-Amplified Spontaneous Emission
Presentation transcript:

HHG Seeding of Mode-Locked Free Electron Lasers David Dunning 8th April 2009

Contents Introduction Mode generation and locking in a FEL. How are discrete modes supported in a FEL? Mode locking. Amplification of an HHG seed without energy modulation. Introducing energy modulation: mode-locked amplifier. Analysis of mode-locking effect Temporal slicing of a pre-filtered HHG seed. Width of radiation envelope. Increased output powers compared to unseeded (SASE) case.

Introduction It will be shown how discrete modes can be supported in a FEL. An explanation of how an electron beam energy modulation is used to ‘lock’ these modes. This allows significantly shorter pulses to be generated than in other FEL schemes. In SASE mode, these pulses are delivered in a train with the train length set by the electron bunch length and the envelope retaining characteristics of the start-up from noise. Will show that an approximately gaussian envelope can be imposed onto this system through seeding. Also, that significantly higher powers may be reached (than in the unseeded case) while retaining the pulse structure. Currently investigating the possibility of reducing the length of the pulse train.

Free electron laser basic mechanism Accelerator-based photon source that operates through the transference of energy from a relativistic electron beam to a radiation field. B E z v x y vx Basic components N S B field E field Electron path The undulator magnet introduces a transverse component to electron beam velocity, allowing it to couple with the transverse radiation electric field.

Resonant wavelength and slippage u r r e- The electrons move slightly less than the speed of light and travel a longer path due to transverse deflections – hence radiation slips ahead. Resonant wavelength is when radiation slips one radiation period ahead per undulator module – allowing continual energy transfer.

Resonant emission – electron bunching Electrons bunch at resonant radiation wavelength – coherent process Gain energy Lose energy Axial electron velocity r Some electrons gain energy from the field and some lose energy leading to bunching on the scale of the radiation wavelength -> this leads to coherent emission.

Types of FEL – low gain and high gain Low-gain FELs use a short undulator and a high-reflectivity optical cavity to increase the radiation intensity over many undulator passes. High-gain FELs use a much longer undulator section to reach high intensity in a single pass – hence are unrestricted in their wavelength range (at least by availability of suitable mirror materials.

Contents Introduction Mode generation and locking in a FEL. How are discrete modes supported in a FEL? Mode locking. Amplification of an HHG seed without energy modulation. Introducing energy modulation: mode-locked amplifier. Analysis of mode-locking effect Temporal slicing of a pre-filtered HHG seed. Width of radiation envelope. Increased output powers compared to unseeded (SASE) case.

Mode formation & locking in a SASE FEL amplifier* Borrow modelocking ideas from conventional lasers to synthesise ultrashort pulses. *

Cavity modes ‘cavity’ length In a cavity only certain discrete frequencies are supported – those for which the cavity is an integer number of periods (No. of periods) 28 29 30 31 32 33 34 35 36 ‘cavity’ length

(slippage in undulator) The ‘synthesised’ cavity is a repeated structure of short undulator modules and chicanes. The radiation slips ahead of the electrons in both. There are discrete modes supported for which this total slippage distance is equal to an integer number of periods. But, only some of these will fall within the undulator bandwidth. 28 29 30 31,32,33 l (slippage in undulator) δ (slippage in chicane) 34 35 36 s (total slippage)

Decreasing the length of the undulator sections is equivalent to increasing their gain bandwidth – this allows more modes to be supported and hence shorter pulses. (this will be referred to as increasing the ‘slippage enhancement factor’ (Se=s/ll) ). 28 29 30 30,31,32,33,34 l δ 34 35 36 s

Axial mode analysis It can be demonstrated that the axial modes generated are formally identical to those of a cavity. The ‘cavity’, however, is significantly shorter, so that only a few modes may fall under the gain bandwidth. This now allows coupling via a modulation introduced at a relatively large frequency. Similarities to DOK: V. N. Litvinenko, Nucl. Instrum. Methods Phys. Res., Sect. A 304, 463 (1991).

Mode-Coupled SASE XUV-FEL @ 12.4nm Spike FWHM ~ 1 fs Without energy modulation the radiation pulses are free to develop in any longitudinal position -> discrete frequencies develop but not regularly spaced radiation pulses along the train.

With an energy modulation of the electron beam the modes can become ‘locked’ in phase and a regularly spaced pulse train develops – will analyse the mechanism for this later.

XUV SASE FEL amplifier with mode-locking Spike FWHM ~ 400 as Ts A regularly spaced pulse train develops with the envelope retaining remnants of SASE noise. From conventional cavity analysis:

1D Simulation: Mode locking mechanism Note that pulses form at the positions of minimum energy gradient and that the pulse structure breaks up towards |A|^2 =1 (normal FEL saturation level).

XUV Output Comparison SASE Spike FWHM ~ 10fs Mode-Coupled Spike FWHM ~ 1 fs Mode-Locked Spike FWHM ~ 400 as

Summary of mode-locked SASE FEL Application of mode-locking techniques, originally from ‘conventional’ cavity lasers, indicate possibility of generating attosecond pulse trains from FEL amplifiers Method tested using full 3D simulation code used in design of e.g. XFEL and LCLS: predicts attosecond pulse trains in good agreement with analysis. Opens up possibility of stroboscopic interrogation of matter using light with the spatiotemporal resolution of the atom. Motivation for seeding: The envelope retains the remnant of SASE noise and the train length is set by the electron bunch length. With seeding we could get a predictable envelope and short train length. Could we get single pulses from this system? The intensity of the mode-locked SASE output is high but it will be shown that it could be higher with seeding (while retaining the pulse structure).

Contents Introduction Mode generation and locking in a FEL. How are discrete modes supported in a FEL? Mode locking. Amplification of an HHG seed without energy modulation. Introducing energy modulation: mode-locked amplifier. Analysis of mode-locking effect Temporal slicing of a pre-filtered HHG seed. Width of radiation envelope. Increased output powers compared to unseeded (SASE) case.

Amplified HHG – no modes* A High Harmonic Generation seed is formed by directing a laser pulse into a gas – the higher harmonics of the drive laser are generated and (in the correct phase) interfere to produce a train of ultra-short pulses with the shape of the envelope set by the drive laser. Previous simulations have shown that the pulse structure of an HHG seed will be washed out in a normal FEL (i.e. without the chicanes). HHG *B W J McNeil, J A Clarke, D J Dunning, G J Hirst, H L Owen, N R Thompson, B Sheehy and P H Williams, Proceedings FEL 2006 Also - New Journal of Physics 9, 82 (2007)

Amplified HHG – with modes With the undulator-chicane system (and no energy modulation) it will be shown that the pulse structure can be retained during amplification. HHG

Amplified HHG – with modes P. M. Paul, et al. Science 292, 1689 (2001) and h is the resonant harmonic of the HHG seed E.g. for operation at the h=65th harmonic of a Ti:Sapphire drive laser with : The mode structure of the FEL must be is matched to the seed by setting the total slippage in one module equal to the HHG pulse spacing.

Amplified HHG – retaining structure The pulse structure is retained during amplification (~approx. 3 orders of magnitude) but the individual pulse widths broaden. HHG Drive λ=805.22nm, h =65, σt=10fs spectrum

No energy modulation → Continual pulse broadening The HHG seed is amplified while retaining an approximately gaussian envelope and pulse structure but there is continual broadening of the individual pulse widths until the structure begins to break up (at |A|2 ~ 1) ~25 modules Module 27

1D Simulation: HHG amplification mechanism

Contents Introduction Mode generation and locking in a FEL. How are discrete modes supported in a FEL? Mode locking. Amplification of an HHG seed without energy modulation. Introducing energy modulation: mode-locked amplifier. Analysis of mode-locking effect Temporal slicing of a pre-filtered HHG seed. Width of radiation envelope. Increased output powers compared to unseeded (SASE) case.

An energy modulation of the electron beam allows the modes to ‘lock’ and the pulse widths to become fixed during amplification.

The effect of the undulator-chicane system is that it locks longitudinal regions of the radiation field to equivalent regions of the energy modulation in successive undulator modules. In this example, effectively only the highlighted regions of the beam are seeded. (a) Slippage in undulator Slippage in chicane p z1 _ |A|2 z1 _

Optimising Longitudinal Alignment of Seed The initial longitudinal position of the seed pulses was varied over one period of the energy modulation and the peak power after 40 modules is plotted. The amplification of the seed is dependent upon longitudinal alignment with the energy modulation phase.

At the maxima and minima of the energy modulation, the energy gradient is minimised and the amplification of the seed is optimal. Would need very low jitter to longitudinally align the seed pulses to the correct regions of the electron beam - but there is a method to avoid this which will be presented later. (b) Slippage in undulator Slippage in chicane p z1 _ |A|2 z1 _

Dependence of pulse width on energy modulation amplitude With sufficient energy modulation amplitude, the pulse width is constant during amplification – compared to continual broadening when there is no energy modulation. ~50 modules

Equivalence of electron beam energy modulation to electron beam quality modulation ~50 modules The introduction of a modulation of the electron beam energy creates regions of the beam which preferentially support the FEL interaction (i.e. the regions of minimum energy gradient). If instead we disrupt the beam periodically, we get the same mode-locking effect: the pulse width is fixed during amplification.

Contents Introduction Mode generation and locking in a FEL. How are discrete modes supported in a FEL? Mode locking. Amplification of an HHG seed without energy modulation. Introducing energy modulation: mode-locked amplifier. Analysis of mode-locking effect Temporal slicing of a pre-filtered HHG seed. Width of radiation envelope. Increased output powers compared to unseeded (SASE) case.

Temporal slicing of a pre-filtered HHG seed It has been showed that certain longitudinal regions of the electron beam preferentially support the amplification process. If we pre-filter the HHG seed, keeping just one frequency, the pulse structure is washed out. This seed is now introduced to the mode-locked FEL. The pulse structure is imposed by the mode-locked FEL! – Avoids issues of matching the mode structures and don’t have tight longitudinal alignment condition.

1D Simulation: Temporal slicing of pre-filtered HHG seed. Note that the pulse structure is retained to higher intensities than the SASE case –explained on next slide.

Width of radiation pulse envelope The pulses towards the head of the train see ‘fresh’ electrons - which are then disrupted, inhibiting the growth of pulses towards the tail. It seems that there is hence a ‘natural’ width of the envelope of the amplified radiation pulse, and that this width narrows towards saturation as the interaction becomes stronger. From initial studies, it seems that there is an optimum width of the seed envelope to match this. This also explains why higher intensities are possible than with mode-locked SASE – where the radiation intensity (and therefore beam quality disruption) is at a similar level along the bunch (i.e. no ‘fresh’ electrons). Is there the possibility of reaching single pulse operation deep into saturation with a long undulator?

Summary Shown how discrete modes can be supported in a FEL and explained how an electron beam energy modulation can be used to ‘lock’ these modes, allowing significantly shorter pulses to be generated than in other FEL schemes. In SASE mode, these pulses are delivered in a train with the train length set by the electron bunch length and the envelope retaining some characteristics of the start-up from noise. An approximately gaussian envelope can be imposed onto this system through seeding and higher powers (while retaining the pulse structure) can be reached than in the unseeded case. The possibility of reducing the length of the pulse train is currently being investigated. Thanks to Brian McNeil and Neil Thompson for the use of slides.