Longboards Mark H.. Drop Decks Most Expensive Fast Easy curving Easy to balance Good for downhill riding.

Slides:

Advertisements

Similar presentations

Simple Machines.

Advertisements

Product Design Lesson 1 – Lamination. Lamination Sometimes it is not economical or suitable to use a solid wood in the production of a product. This is.

LONGBOARD MAKE PROJECT Caroline Manning& Cameron Baller.

How to build a bridge!.

Tools and Fasteners And, Their Uses.

Longboarding Physics Alex Briestensky and J.P. Hajjar

Cantilever Tower Project

UNIT 3 TECHNICAL MATERIALS WOODS. CLASSIFICATION WOODS NATURAL SOFTWOODS They come from coniferous trees. They are ever green, and have got NEEDLE shaped.

Objective 2.02: Selecting Furniture. Understanding furniture construction will help you choose the highest quality furniture for your money.

Ms. Gripshover Landscaping Unit 18 INSTALLING PATIOS, WALKS, AND DECKS.

SEACORK INSTALLATION ON A CATAMARAN The first step is to make templates of all corner pieces to be cut from sheet material, which will be used for border.

The Raven Level 2 Rubber Band-Powered Flight. Dimensions 2”

Creative Inventions and Robotics Laboratory.

SNUG-LOANS.COM. snug-loans.com Need an Instant Loan? Get Up to $1,500 in as fast as 1 hour.

1. Veneering Veneering is a method of taking thin slices of more expensive wood and gluing them onto cheap manufactured boards. Why veneers are used:

Mantle Clock. Beginning Steps Cut 2 piece 20 x 5 to make the 2 sides and top/bottom Cut 1 10 ¾ and 1- 9 from each 20 piece. This will make a side and.

Roller coaster history Turning points in roller coaster history.

Balsa Glider Construction

Objective 5.02: CRITIQUE components of quality furniture construction

Building a clock PART 1: The Body. Gathering materials  The wood that you will be using is called Maple. You can identify it by knowing that it is: Heavy.

CLAY VOCABULARY.

1. b. Rip Saw 2. d. Used for cutting with the grain.

Agriscience Toolbox Plan of Procedure 1. Table Saw (equipment) Rip the bottom of the toolbox to a width of 10 inches.

The Gladiators Helmet By George Shanahan. The first thing I did was to inflate a balloon. I then mixed up some wall paper paste, and covered the balloon.

Topic: Transmission Towers Objective: ▫ Build transmission towers from balsa wood. 1 Summary: ▫ One to one-and-half hours is given to students. In their.

Sculpture Created by J. Walker & L. McHugh ‘07.

Left side Right side Note pad Roll block. The Plan.

Table of Contents Unit 1- Understand the Problem Unit 2- Gather Information Unit 3- Develop Solutions Unit 4- Implement A Solution Unit 5- Test and Evaluate.

By: Maxim Petrovsky.  Unlike Skateboards the function of a longboard is mainly for cruising, Downhill racing, Slalom racing, or a mode of transportation.

By: Yoshua Bekuray. First you should skate around and get to know the park.

By: Yohana Cantua & Fernando Ontiveros Materials one book cover or large piece of smooth paper one book with a hard, glossy cover one book with a rough.

Construction The Core – Using pallets, the wood (Beech is a common type of wood used to make snowboards) will be cut into long, thin vertical strips (Snowboards.

University of Nebraska–Lincoln Know how. Know now.

Project Overview Introduction & Product Analysis

This is a self-propelled hovercraft, designed to use only one motor which will both lift the vehicle and propel it forward. The hovercraft works by creating.

Bending and Laminating Wood

Equipment for Surfing SurfboardsSurfboards Surf racksSurf racks WetsuitsWetsuits.

We are all in a throw away society so we need to use what we have with limited wasted money, we also live close to a beach and have easy access to surf.

1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape.

Sewing Tools. Besides a sewing machine, you will need a few tools of the trade. You will need: -Measuring tools -Cutting tools -Marking equipment -Other.

Weather Vanes.  What is a weather vane? A weather vane is used to determine the direction of wind. It is also called a wind vane.  Why is it important.

Joining Materials Theory. Knowledge and Understanding.

Bridge Specifications 10” Span 2 ¼ “ Outside width 2” Inside width 1” on each end must rest on the test supports 1” square opening in the center of the.

Woods and Processes Theory. Knowledge and Understanding.

 Whole Longboard (W x L): 9.6 x 41 inches  Deck Type: Drop Deck  Deck Material: Full Maple Laminate  Deck Long: 41 inches.

Sewing Equipment. Tape measure – used to take body measurements; 60” long.

LO - To be able to identify a range of different timber and manufactured board and their applications - To understand the different timber properties and.

Tools and Machines. Band Saw Characteristics Long, thin blade. Mounted on a table or can be handheld. Uses Cutting materials like wood or foam into irregular.

 Whole Longboard (W x L): 10 x 40 inches  Deck Type: Traditional Cruiser  Deck Material: Hardwood Maple  Ply: 7 Plies 

 Whole Longboard (W x L): 9.25 x 41 inches  Deck Type: Freestyle Shaped  Deck Material: Bamboo and Hardwood Maple  Wheel.

Woods joints are often glued to make them permanent. The strength of the joint depends on the marking out and cutting (accuracy)

 Whole Longboard (W x L): 10 x 44 inches  Deck Type: Traditional Cruiser  Deck Material: Bamboo and Hardwood Maple  Deck.

By Jordan Latcham First the Supplies Needed Deck.

Common Woodworking Hand Tools

BEST LONGBOARDS

By – Sector 9 Blue Wave Lookout drop through Complete Long board Skateboard, 9.6-Inch x 42.0-Inch By –

How to Longboard By: Craig Mazzeo.

Wood Glue & Preserving and Finishing Products

Intro to FCS Lenape High School

Unit 4. The materials. Wood

PLIERS To grip objects and in various types such as:

History & Physics of Skateboarding

The size of the Band Saw is determined by the diameter of the wheels;

BC Technology Education Association

Fastening Wood Turn to Unit 10 on page 117.

Balsa Glider Construction

BC Technology Education Association

Machines 5. Compound Machines

BC Technology Education Association

Tips To Learn Skateboarding On A Penny Board How To Learn SkateBoarding On Penny Board.

Presentation transcript:

Longboards Mark H.

Drop Decks Most Expensive Fast Easy curving Easy to balance Good for downhill riding

Cruiser Cheapest Harder to turn Harder to balance Good for street riding Good for sharp turns

Pin Tail Similar to the Cruiser Cheapest Hard to balance Good for flat paths

Process 1.Cut wood to size 2.Cut out design 3.Steam the wood for an hour so the wood can bend 4.After steaming put in mold instantly 5.Leave in mold for 8 hours 6.Glue the 4 layers together and place back in the mold for 8 hours 7.Sand the whole board 8.Paint, grip tape, install trucks and wheel