1 | INALA TECHNOLOGIES INSTALLATION TRAINING: ECS (EQUIPMENT COMMUNICATIONS SYSTEM) ECS (ETH/GPRS) COMMISSIONING VERSION 1.0

2 | ECS-(ETH/GPRS) COMMISSIONING COMMISSIONING: ECS (ETH/GPRS) PROCEDURE

3 | ECS (ETH/GPRS) - COMMISSIONING SAM Training Setting up of the unit: Power unit on Connect using the “ECS2” ECT Set-up the communication ports for the devices you are connecting to it Set-up the Sever IP address and APN – Customer Dependent Click on “update unit” after making a change to save the configuration to the unit. Check that LED1 is on to indicate that it is logged onto GPRS and the APN - Customer Dependent. Call to commission site with representative. Port Settings SAM2 & Access Control RS484 = Physical port 1 – Virtual Port 301, Baud rate 9600 L&G and/or Deep Sea RS485 = Physical port 2 – Virtual Port 309, Baud rate SAM1.5 = Physical port 3 – Virtual Port 310, Baud rate Enable Flow Control Rectifier = Physical port 4 – Virtual port 302, Baud rate depends on type of Rectifier. Generator = Physical port 5 – Vittual port 304, Baud rate depends on type of Generator. *Note – Check following slide for detail information of above procedure LED Indications LED 1 on = GSM Network found and Logged onto GPRS ECS (Eth/GPRS) Communication Cable: A “USB Printer cable” must be used between the ECS(Eth/GPRS) and the computer. Once Connected open the “ECS2 ECT” software. Click on USB and Login

4 | ECS (ETH/GPRS) – PHYSICAL PORT NUMBERS SAM Training PORT 1 – RS485 PORT 2 – Isolated RS485 PORT 3 – RS232 PORT 4 – RS232 PORT 5 – RS232 PORT 6 – RS232 PORT 7 – RS232 * The physical port that is connected to the SAM or Access Control must be selected as the “UDP PORT” GND 48VDC Earth

5 | SOFTWARE FOR ECS (ETH/GPRS) (EQUIPMENT COMMUNICATION CONTROLLER) – USING SIM SAM Training Communication Controller Software (ECS2 ECT): ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ECS2 ECT V 1.4” Firmware Version is viewed on the bottom as indicated with the Red circle EG: “Build: 1.4” IP address is automatically allocated to sim card and is displayed. Enable: 1.GPRS Modem 2.Input APN name - Customer Dependent 3.Input Server IP and UDP port - Customer Dependent 4.Set Port configuration 5.Click on Update unit 6.Wait for unit to complete updating

6 | SOFTWARE FOR ECS (ETH/GPRS) (EQUIPMENT COMMUNICATION CONTROLLER) – NOT USING SIM SAM Training Communication Controller Software (ECS2 ECT): ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ECS2 ECT V 1.4” Firmware Version is viewed on the bottom as indicated with the Red circle EG: “Build: 1.4” IP address is must be inserted if no GPRS SIM card is being used 1.Insert IP, Mask & DG IP addresses 2.Input Server IP and UDP port - Customer Dependent 3.Set Port configuration 4.Click on Update unit 5.Wait for unit to complete updating

7 | EQUIPMENT COMMUNICATION CONTROLLER – PORT & SERVER ALLOCATIONS SAM Training Virtual Port Allocations 301 SAM2 or SAM3 and Access Control 302 Rectifier A 303 Rectifier B 304Generator 305 AVR 306 BMON 307Fuel Cell Fuel Cell 2 309Energy Meter / Fire System 310 SAM 1.5 REC Vodacom Server NameVodacom UDP Server IPUDP Server Port ZABLV CEN ZABLV EAS ZABLV LIM ZABLV MPU ZABLV SGC ZABLV SGS ZABLV WES NGA Existing Server Telkom Server NameTelkom UDP Server IPUDP Server Port Neotel Server NameNeotel UDP Server IPUDP Server Port Operator NameAPN Name VodacomVodameter Neotelinternet

8 | EQUIPMENT COMMUNICATION CONTROLLER – COMS WIRING SAM Training Communication Cable Consumables ECS (Eth/E1), ECS-L way Ribbon Cable way IDC connector for 10 way ribbon cable 3. DB9 IDC, male and female for 10 way ribbon cable ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L 1. DB9, male and female, solder type 2. Milar cable used with point 1 above (Same as SAM2 Coms cross over cable) ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L 1. RJ9 – small 4 way 2. RJ11 – large 4 way 3. RJ way 4. RJ45 – 8way 5. Cable for each above 6. CAT5 cable Possible Communication Cables needed 1. SAM SAM2, SAM3 & Access Control 3. Energy Meter (Landis & Gyrr) Rectifier 4. Rectifier (Battery Tech, Grintek, ASM, etc) 5. Generator (Lovato, Deep Sea, Intellilite, etc) 6. Fuel Cell (Idatech, Gencore, etc)

9 | ECS (ETH/GPRS) COMMUNICATION WIRING SAM2 & ACCESS CONTROL SAM Training

10 | ECS (ETH/GPRS) COMMUNICATION WIRING SAM1.5 SAM Training

11 | ECS (ETH/GPRS) COMMUNICATION WIRING LANDIS & GYRR SAM Training

12 | ECS (ETH/GPRS) COMMUNICATION WIRING BATTERY TECH SM65 SAM Training

13 | ECS (ETH/GPRS) COMMUNICATION WIRING BATTERY TECH SC200 SAM Training SC200 LAN CONNECTION SC200 RS232 CONNECTION FRONT VIEW REAR VIEW

14 | ECS (ETH/GPRS) COMMUNICATION WIRING BATTERY TECH SM50 SAM Training

15 | ECS (ETH/GPRS) COMMUNICATION WIRING GRINTEK GT500 SAM Training

16 | ECS (ETH/GPRS) COMMUNICATION WIRING DEEP SEA SAM Training

17 | ECS (ETH/GPRS) COMMUNICATION WIRING LOVATO SAM Training

18 | CLICK TO EDIT MASTER TITLE STYLE THANK YOU