Vaccon Vacuum Pump 2” Diameter flexible tubing to fit inside U-Bolt (not shown) will be used to attach tubing to framework. Vaccon Inline Venturi Vacuum.

Slides:

Advertisements

Similar presentations

Quick Release gripper overview and development time line.

Advertisements

Introduction to Pneumatic Components Build a Working Pneumatic Circuit

“The Strength of Experience”

VentStop V.C.U Step 6. Lower down all 4 sides, make sure they are as flat as possible and there are no large rocks underneath. Check orientation. Step.

ME240/107S: Engine Dissection

Optimum Round Pool Instructions. Prepare the pool site Remove all the grass on a surface 2’ wider than the size of the pool Level the ground.

Engine Fundamentals TRF 210.

Heavy Concrete Construction Formwork

Select one of the following:

Optical Manufacturing Solutions 1 Probe Assembly.

Installation. Indoor Unit Installation Typical Installation.

Aims and Objectives Aim To be able to recognize operation of a carburettor within an internal combustion engine Objectives Be able to describe the operation.

SMALL ENGINES CARBURETION

Fuel System The fuel system supplies the air and fuel necessary for an engine to produce power. The fuel system includes: Air Cleaner Fuel Supply Carburetor.

Pneumatic Components & Systems Team 1640 Clem McKown – mentor November 2008.

The bucket of the excavator at a construction site is subjected to 1200-lb and 700lb digging forces at its tip. Determine the magnitude and direction.

Diesel Engine Components

Sava air bags. The new equipment Air Bags Kevlar reinforcing w/ thick, multi-layer rubber shell 24” x 24” positive grip surface w/ safety straps Max load:

WASH Cluster – Groundwater Pumping GWP GWP1 1 Groundwater Pumping Session 1 Handpumps.

 Air! A pneumatic assembly is one that converts energy stored in compressed air to mechanical energy. Electrical Energy Compressed air Mechanical force.

1 Hose and Lines. 2 High side / low side System with an expansion valve High SideLow Side Condenser Evaporator Receiver/Drier Compressor Expansion valve.

Practical Labs ImpedanceWeighing Air Compression & ExpansionCompressionBoiling Point Versus Pressure.

Tank and Inline Chiller Setup. Equipment list  Bleach  Aquarium (min 10 Gal)  Chiller (there are several types)  Insulated box or some kind of tank.

9.01 Four Stroke Cycle and Engine Types References: FTGU pages 51-53

Engines Internal combustion engine needs

COMMERCIAL REFRIGERATION

Section 5: Commercial Refrigeration

4 Stroke engine Stroke is defined as the movement of the piston from the 'bottom dead center' (BDC) to the 'top dead center' (TDC) or the other way round,

Unit A 6-1 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Systems of the Engine.

4 Cylinder Engine TDC (Top Dead Center) BDC (Bottom Dead Center) Piston Cylinder.

Vacuum Tube Lifters Basic Overview. Vacuum Lifting 1Two types of ‘vacuum lifting’ exist Where vacuum is generated to apply a grip using suction pads.

How a 4 Stroke Engines Work

Heating element to heat rim to approx. 600℉ Track to move cups from one subcomponent to the next. Linear actuator for control upward motion of cup. Cup.

Manip 6” Diameter TSP shield Top Level Middle Level Bottom Level Lower Level CF flanges Not threaded except wide bore Table top 3’ high (Al table top)

How Car Engine Works. Training Norms Car Engine Layout - Car Engine Concept - Car Engine Construction - Types of Car Engine - Car Engine Animation.

Diesel Engine The only difference between diesel engine and a four-stroke gasoline engine is: No sparkplug on Diesel engine. Has a higher compression ratio.

Installation. Indoor Unit Installation Typical Installation.

Smoking Sue and Baby Too This doll is a little more complicated than my Smoking Sue I made last time, but still simple to make. You will need a doll with.

1 Cryostat assembly, integration and commissioning procedures M.Olcese Version: 07 May 2008.

Installation. Indoor Unit Installation Typical Installation.

Water Supply Skill Drills.

Prepared by : Pavan Narkhede

“DIESEL ENGINE” A SUMMER TRAINING PRESENTATION ON

Zack Burchman Travis Gang Dana Geer Ryan Neary Matt Seekins Faculty Advisor: Mike Rosen GMCR Contacts: Wade Hodge Paul Comey Jason King.

EAST ELECTRIC 1 SYSTEMINTEGRATOR & SALES PARTNER INDUSTRIAL AUTOMATION FROM ONE PROVIDER.

9.26 Assume that you have a sample of gas in a cylinder with a movable piston, as shown in the following drawing: Redraw the apparatus to show.

KNUDSEN PUMP. WHAT IS IT? Vacuum pump Principal of thermal transpiration temperature gradient causing the gas molecules to move from one side of the tube.

ENTC-370PROF. ALVARADO1 Fluid Mechanics LAB: Actuator Constructions and Component Identification.

Long Bo for LAPD Hans Jostlein10/20/2011 December 15, 2015 Long Bo for LAPD 1.

Chapter 39 Cooling System Fundamentals.

MICE RF Coupler Modifications Update 4/30/2015 Allan DeMello.

AfterSalesTraining Welcome to AfterSalesTraining.

Small Engines Ag  Identify basic terms and definitions associated with carburetion  List and identify individual engine parts related to carburetion.

Sentek Training Presentation © 2003 All rights reserved Sentek Pty Ltd Sentek Sensor Technologies Installation of EasyAG 50 and EasyAG 80.

Diesel Engine Components

Basic Engine Terms. Dead Center –The term identifies the relation between the positions of the crankshaft and the piston. When the piston is at its outward.

Pistons and piston rings

Engine Lubrication Systems

Suspension Systems - 1 Topics covered in this presentation:

Panda Solenoid Content Interface Box Cold Mass Layout Cooling Lines

Understanding Principles of Operation of Internal Combustion Engines

OBJECTIVES State the principles of vacuum and the vacuum booster theory. Discuss how a vacuum brake booster operates. Discuss the vacuum booster operation.

Sphere Option for Helical spring CF16 Bellows Adjustment bolts (horizontal plane) CF38.

Louisiana Tech University

LST Module Installation

Understanding Principles of Operation of Internal Combustion Engines

How Car Engine Works.

Presentation transcript:

Vaccon Vacuum Pump 2” Diameter flexible tubing to fit inside U-Bolt (not shown) will be used to attach tubing to framework. Vaccon Inline Venturi Vacuum Pump used to hold cup down during vacuum. Bimba Flat Cylinder Piston used to raise lower vacuum pump to 2” tubing. Box to hold evacuated materials. To be purchased later. Flange to attach tubing to box. Framework will be designed in next design phase to go along with heat/punch design to utilize same materials and to ensure compatibility. Grounds & Foil

Vaccon Inline Venturi Vacuum Pump. Compressed air will enter through the bottom and create a vacuum strong enough to hold down cup during vacuum removal of foil and grounds. Vaccon fitting to attach suction cup. Vaccon universal suction cup,.85” diameter. Connection plate to be made in shop at a later date. Bimba Flat Cylinder Air Cylinder. ¾” Bore, ½” Stroke.