Testing Alternator Output By Vance Bloom & Florante Boac SC6.

Slides:



Advertisements
Similar presentations
STARTING & CHARGING SYSTEM DIAGNOSIS
Advertisements

Spark Plug Replacement
Charging System Tests & Voltage information Checking the charging system with just a volt meter.
Cooling System Service CS6 NATEF Task A.1 D.7 By Vance Bloom.
REMOVE AND INSTALL THERMOSTAT AND TEST OPERATION CS4 A.1 D.6 P-5/6.
A/C Generator Systems.
Classroom & Laboratory Safety
How to Change Your Oil By: Sam Wallace. Overview Introduction (Importance) When? Tools Required Changing the Oil Clean Up.
Shop Safety By Brent Tubbs Mount Logan Middle School.
Register Digital Multimeter Usage Click Register to begin the course.
USING A DIGITAL VOLT- OHM - METER Automotive Technology Learning How Electricity Works.
Why EcoStar?. Marc Ellison V.P. of Operations Save fuel expenses and maintenance labor by automatically eliminating unnecessary idling.

Diagnose the Starting System. Fender Covers ! You must have a strong battery to test the starter.
Electricity & Electronic Systems SAFETY. When are Safety Glasses required? All students and visitors MUST wear safety glasses at any time there is any.
PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Charging System tests & Voltage information Checking the charging system with just a volt meter.
Meter Lab Introduction to Electricity Assignment for tomorrow: Read chapter R1.
Load Testing a Battery SC4B Objective Student will determine the state of charge of a battery and load test a battery in or out of the vehicle. Do you.
VAT: Volt Ampere Tester
Charging System Fundamentals
Charging system PT 1 LSy_w.
BATTERY State of Charge SC1 Objective Student will determine the “State of Charge” of a battery using the “Voltage Method” and document results. Student.
Battery Principles.
COMP 364 Prof Jess UEAB 2006 Power Supplies and UPS.
BATTERY.
Cooling System Service CS6 NATEF Task A.1 D.7. O BJECTIVE Student will inspect, test and flush cooling system.
General SHOP SAFETY In technology education, SAFETY is regarded as essential for at least two reasons. #1 – The natural concern for people’s welfare.
1 Battery Safety, Servicing & Testing R. Bortignon.
BATTERY DRAW TEST SC10 By Vance Bloom Objective Student will determine if an abnormal “Key OFF Battery Drain” is present.
Register Digital Multimeter Usage Click Register to begin the course.
ELECTRONICS AND SAFETY Scarlett, Dash, Sam, Ashley, and Eric.
Counting Servo Gear Teeth living with the lab Take apart one of your servos to see what it’s like on the inside. Count the number of teeth on each gear,
USING A DIGITAL VOLT- OHM - METER Automotive Technology Learning How Electricity Works.
EU 1000i and EU 2000i SECTION: Tools and Equipment ISSUED: REVISED: ##-####
NGfL CYMRU GCaD WOOD OCCUPATION SKILLS WORKING AREAS HEALTH & SAFETY MATERIALS HANDLING & STORAGE WORKING AREAS.
Check Spark Plug Wires. Objectives Student will visually inspect and test with ohmmeter, spark plug wires, evaluate, then recommend if replacement is.
TUNE UP SKILL T-1 AIR FILTER Removal, Installation and Evaluation.
Charging a Battery SC2 Objective Student will determine the state of charge of a battery and charge a battery in or out of the vehicle.
General Safety. A student may not work in the shop unless the instructor is present. Absolutely no exceptions !!
Front Disc Brake Inspection By Vance Bloom Murrieta Valley High School ROP Automotive Technology.
Laboratory Safety Rules
Electronics Speaker Project Mr Sanders.
BATTERY State of Charge SC1 By Vance Bloom Objective Student will determine the “State of Charge” of a battery using the “Voltage Method” and document.
PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Tune-up Procedure.
© Goodheart-Willcox Co., Inc. Permission granted to reproduce for educational use only Battery Testing and Maintenance.
Cooling System CS 1B Evaluating Coolant Checking For Dissolved Metals.
TUNE UP SKILL T-2 PCV VALVE Removal, Installation and Testing Operation By Vance Bloom CTE Automotive Technology Hemet High School.
COOLING SYSTEM: CHECK CONDITION AND CONCENTRATION OF COOLANT CS1 A.1 D. 7 P-1.
COOLING SYSTEM: CHECK CONDITION AND CONCENTRATION OF COOLANT CS1 A.1 D. 7 P-1.
Boost/Jump Starting SC3B Jump Starting a Vehicle With Jumper Cables By Vance Bloom.
We save should energy We should save energy.
WARM UP 1. What happens when you create a circuit with a battery, a wire and no resistor? 2. What are domains and how do they relate to magnetism? 3. When.
Lab 2. Do now Answers Improperly grounded outlets can cause errors in a computer system that may not be immediately apparent from internal diagnostics.
Classroom and Laboratory Safety
Effective Way to Test the Battery of your Car
USING A DIGITAL VOLT- OHM - METER
Testing Alternator Output Vance Bloom & Florante Boac
Classroom and Laboratory Safety
Waveforms & Timing Diagrams
DC motor.
STARTER DRAW TEST SC8 By Vance Bloom.
BATTERY State of Charge SC1 By Vance Bloom.
Removal, Installation and Testing Operation CTE Automotive Technology
Charging a Battery SC2 By Vance Bloom.
Series Circuits Makeup Lab
P2 - Physics Mains Electricity.
Transmitted by the expert from the India
USING A DIGITAL VOLT- OHM - METER
THROTTLE POSITION (TP) SENSORS
Presentation transcript:

Testing Alternator Output By Vance Bloom & Florante Boac SC6

Materials Required

Safety Glasses Digital Volt-Ohm-Meter

Vehicle

STEP 1 WEAR EYE PROTECTION!

STEP 2 Put Volt-Ohm-Meter on 20Volt DC Scale

STEP 3 Test Battery Voltage with vehicle OFF Write Down Reading on Skill Sheet

STEP 4 Start Vehicle

STEP 5 Test Battery Voltage with vehicle Idling Write Down Reading on Skill Sheet

STEP 6 Increase Idle to 1800 RPM Write Down Voltage Reading

STEP 7 Turn On Headlamps Record Voltage Reading

If All Readings Are Above OFF Voltage Alternator PASSES Test

If Any Readings Are Below OFF Voltage Alternator FAILS Test

Clean Up Your Mess! Put Away All Tools

QUESTIONS ? CONTACT Vance Bloom

THE END

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.