IPC-2221 8.3.1.7 RADIAL- COMPONENTS Angularity is required for clearance in the next higher assembly; or That edge of the body nearest the surface of the.

Slides:



Advertisements
Similar presentations
Geometry Point Line Line segment Ray Plane Parallel lines
Advertisements

Chapter 7 Dimensioning.
Chapter 7 Dimensioning.
IPC COMPONENT PLACEMENT
Test Chamber Assembly, 1.5M Long (59.00”) Vacuum Tube, 4.00 OD x 3.50 ID Vacuum Tube, 3.75 OD x 3.51 ID 3.375” CFF, Non-Rotatable Feedthrough, Ceramtec.
> >
Dimensioning Chapter 9.
P247. Figure 9-1 p248 Figure 9-2 p251 p251 Figure 9-3 p253.
One Way Circuits Limited
Warm-up Review Take Home Quizzes. There will be a 3 question In Class Quiz based on them.
Basic Assembly Constraints and Concepts
1 EECS 373 Design of Microprocessor-Based Systems Prabal Dutta University of Michigan Lecture 13: PCB Design Oct 12, 2010 Some material from Mark Brehob.
Prisms Fun with by D. Fisher
Dimensioning (WEEK 2).
Vertex – A point at which two or more edges meet Edge – A line segment at which two faces intersect Face – A flat surface Vertices, Edges, Faces.
IPC-SM Board Size & Panel Construction In order to fully utilize the automation technology associated with surface mount components, a designer.
Lesson 9 2D Sketches Angular dimensions Sketch Dimensions Offset.
IPC Datum Features Datum features indicate the origin of a dimensional relationship between a toleranced feature and a designated feature or.
Orthographic Multiview Projection Multiview Projection.
IPC-SM-782 Soldermask vs. Lands Only
IPC Stress Relief Lands and terminals shall be located by design so that components can be mounted or provided with stress relief bends in.
Workbench project schematic Place the new component on its source.
IPC Thermal Transfer Components, which for thermal reasons require extensive surface contact with the board or with a heatsink mounted on the.
IPC Bus Bar Bus bars are usually in the form of preformed components that are part of the printed board assembly and serve the function of.
Warm-Up 1) Draw a polygon that is not convex. 2) Find the measure of an exterior angle of a regular decagon. 3) Find the circumference and area of a circle.
New design With fewer parts and easier manufacture degrees 20mm 245.
Space Figures & Nets, Surface Areas of Prisms & Cylinders Unit 5, Lesson 1 chapter%20ten.ppt.
IPC Conductor Width and Thickness The width and thickness of conductors on the finished printed board shall be determined on the basis of the.
12.3 Surface Areas of Prisms. Objectives: Find lateral areas of prisms Find surface areas of prisms.
IPC-SM Soldermask Issues Rework of Surface Mount Assemblies due to soldermask related defects is cited as a major cause of problems by assembly.
IPC In-Circuit Test Fixtures In-circuit test fixtures are commonly called bed-of-nails fixtures. A bed-of- nails fixture is a device with.
I go on and on in both directions What am I?. A line.
Polyhedra & Surface Area. Polyhedra Polyhedron – Solid with all flat surfaces that enclose a single region of space. Basically, just a 3D figure whose.
IPC Mounting Over Conductive Areas Metal-cased components shall be mounted insulated from adjacent electrically conductive elements. Insulation.
POINTS, LINES, & PLANES 9-1. BASIC GEOMETRIC FIGURES NAMESAMPLESYMBOLDESCRIPTION Point Point ALocation in space Line AB Series of points that extends.
How to make a PCB.
IPC Part Support All parts weighing 5.0 gm, or more, per lead shall be supported by specified means, which will help ensure that their soldered.
The Lego Man Basic 3D Modelling. The Head Use the Revolve Tool to get the sketch from 2D to 3D.
Learning Objectives • Create sweep features. • Create lofted features.
Basic Assembly © 2012 Project Lead The Way, Inc.Introduction to Engineering Design.
IPC Standard Surface Mount Requirements Automatic assembly considerations for surface mounted components are driven by pick-and- place machines.
11-1 Space Figures and Cross Sections Objectives To recognize polyhedra and their parts To visualize cross sections of space figures.
IPC Conductive Material Requirements The minimum width and thickness of conductors on the finished board shall be determined primarily on the.
Geometry 10-1 Space Figures and Nets. Vocabulary Polyhedron – A solid formed by polygons that enclose a single region of space Face – Flat polygon surfaces.
Computer – Aided Design Terminology You must have a generic understanding of commands and techniques which are used in a number of packages (YOU CANNOT.
The reading is 7.38 mm. The reading is 7.72 mm.
3D CAD What you need to know…. Main areas of CAD Modelling Techniques Modelling Edits Assembly Materials &Environment Use of Models File Types Basic Terms.
11-3 Surface Areas of Pyramids and Cones
Kursus “electronic assemblies & SOLDERING Technique”
ELECTRONIC ASSEMBLIES AND SOLDERING TECHNIQUE –PART II
conventional rear wheel drive, a beam axle assembly
Signing Plan Design - At Grade Intersections TEM Chapter 6-8
IPC-A-610E SOLDERING.
Geometry Point Line Line segment Ray Plane Parallel lines
Lesson Geometric Solids -- Prisms and Cylinders
Space Figures and Nets Geometry 10-1.
Wicking: Requirements
WARNINGS Side Description COMPONENTS SIDE (TOP) EXPRESSIONS BOARD 1/2
Geometry Point Line Line segment Ray Plane Parallel lines
Geometry Point Line Line segment Ray Plane Parallel lines
DIMENSIONING WORKING DRAWINGS
Space Figures & Nets, Surface Areas of Prisms & Cylinders
Grade 6 Measurement Unit
CHAPTER 3 Dimensioning.
Geometry Point Line Line segment Ray Plane Parallel lines
Geometry Point Line Line segment Ray Plane Parallel lines
Miniature Train Wheels.
DIMENSIONING WORKING DRAWINGS
Geometry Point Line Line segment Ray Plane Parallel lines
Geometry Point Line Line segment Ray Plane Parallel lines
Presentation transcript:

IPC RADIAL- COMPONENTS Angularity is required for clearance in the next higher assembly; or That edge of the body nearest the surface of the board parallels the board surface within 10 degrees and is no less than 1.0 mm and no more than 2.3 mm from the surface. Components of configurations F through J of Figure 8-22 are not included under the angularity exception. Figure 8-23 Radial two lead component mounting, mm

IPC RADIAL- COMPONENTS Radial-leaded components with coating meniscus on one or more leads should be mounted such that there is visible clearance between the meniscus and the solder fillet. Trimming of the meniscus is prohibited. Figure 8-24 Meniscus clearance, mm

IPC RADIAL- COMPONENTS Radial-Leaded Components (3 or more Leads) - Radial-leaded components with three or more leads vary in lead spacing. The design lead spacing is generally a function of the spacing at which the leads exit from the body of the component (see Figure 8-25) and the nearest pattern of grid intersections that provides for suitable conductor routing. Figure 8-25 "TO" can radial-leaded component, mm

Feedback: Privacy Policy Feedback
Do Not Sell My Personal Information
About project: SlidePlayer Terms of Service

© 2025 SlidePlayer.com. Inc. All rights reserved.