OSHA 10 hr Training OSHA 10 hr Training Hand tools Hand tools Power tools Power tools.

Slides:

Advertisements

Similar presentations

FHM TRAINING TOOLS This training presentation is part of FHM’s commitment to creating and keeping safe workplaces. Be sure to check out all the training.

Advertisements

29 CFR 1910 SUBPART O Machine Guarding OSHAs Most Cited Serious Violations in General Industry : FY 2007.

OSHA Office of Training and Education

Safety : Power Tools Introduction to Industrial Technology Spring 2014 Mr. Shubert.

Tools - Hand and Power 29 CFR 1926 Subpart I

HAND and POWER TOOL SAFETY

Mechanical Engineering: Motion Transmission

MACHINE TOOL PRACTICES SECTION A - Introduction Shop Safety Machine Tool Practices, 8 th Edition Richard R. Kibbe, John E. Neely, Roland O. Meyer, Warren.

Copyright © by NCCER, Published by Pearson Education, Inc. Core Curriculum Module National Center for Construction Education and Research Slide.

Portable Tools.

Machine Guarding Slide Show Notes

Hand and Portable Power Tools Hazard Recognition.. Inspect tools daily Tool Fits Job.

Proprietary and Confidential HAND TOOL SAFETY Safety Leadership Training Series "Our loss control service is advisory only. We assume no responsibility.

Subpart P Gayle W. Fratto Manager, Safety Engineering Branch Georgia Tech’s OTI Education Center.

OSHAX.org - The Unofficial Guide To the OSHA

ACTUATOR. An actuator is a type of motor for moving or controlling a mechanism or system. It is operated by a source of energy, usually in the form of.

Power/Hand Tools Valley City State University | Facilities Services | OSHA Office of Training & Education.

Tools – Hand and Power 1926 Subpart I - Tools – Hand and Power

Tool Safety. Rule #1 – Do Not Fall On Your Drill.

School Safety Training

Tool Safety – Hand and Power 1. Safety Hazards Workers using hand and power tools may be exposed to these safety hazards:  objects that fall, fly, are.

OSHA Office of Training and Education

Machine Guarding.

POWER STEERING SYSTEM IN AUTOMOBILE

Striving For Safety Excellence HunterDouglas Corporate Environmental, Safety, Risk Management Machine Guarding April 2011.

OSHA Office of Training and Education

OSHAX.org - The Unofficial Guide To the OSHA1. Introduction 2OSHAX.org - The Unofficial Guide To the OSHA Crushed hands and arms, severed fingers, blindness.

ELEVATOR PARTS FOR THE CAR PARTS FOR THE CAR ANGLE IRON-4X3X3/8 QTY- WT.-8.5LBS/FT LENGTH-6.5 FEET ANGLE IRON-4X3X3/8 QTY- WT.-8.5LBS/FT LENGTH-6.5 FEET.

Tools – Hand and Power.

Annual Refresher Training Tools and Machine Guards.

1 Portable Powered Tools Use the Right Tool the Right Way.

Hand and Power Tool Safety Standards Training

Mechanisms from Simple Machines

Joe Bateman, ISRI Safety 1 Machine Guarding. ISRI Safety 2 Introduction Machine guards are essential for protecting workers from needless and preventable.

TOP 10 VIOLATED STANDARDS In Fiscal Year 2001, based on most serious citations according to OSHA As published in the National Safety Council’s Safety and.

OSHA Office of Training and Education - Revised by TEEX 12/05/07 1 Machine Guarding.

MACHINE GUARDING. contents  What is a Guard?  Why are guards used?  Where should machine guards be used?  Hazardous Machine Areas  Hazardous Actions.

Forging new generations of engineers. GEARS Presentation Objectives Identify parts of the gear trainer Identify gears Identify gear terminology Identify.

Hand and Portable Power Tools 29 CFR, Subpart P

EVD Apparatus Maintenance. EVD2 EVD Apparatus Maintenance  Basic Systems Battery Braking Coolant Electrical Fuel Ref. Unit 5 LP 1 (Lesson 10) Hydraulic.

Fischertechnik Mechanisms

PPT 10-hr. Construction – Tools v Created by OTIEC Outreach Resources Workgroup Tools – Hand and Power 10-Hour Construction Outreach.

Hand and Power Tools for construction. Basic tool safety  Keep in good condition  Right tool for job  Inspect tools  Operate tools correctly  PPE.

EVD Apparatus Maintenance. EVD2 EVD Apparatus Maintenance  Basic Systems Battery Braking Coolant Electrical Fuel Ref. Unit 5 LP 1 (Lesson 10) Hydraulic.

Mechanical drive mechanisms

OSHA Federal Standards October 1, 2011 – September 30, 2012.

Hand and Power Tool Safety. Hazards Workers using hand and power tools may be exposed to these hazards: –Sharp or abrasive objects –Objects that fall,

PART II Design of a Mechanical Drive 2-1 Objectives and content of Part II A mechanical drive is called sometimes a power transmission that serves.

Machine guarding.

fischertechnik Mechanisms

Chapter 20 Engineering Drawing and Design Engineering Drawing and Design Sixth Edition Belts, Chains, and Gears.

Tool Safety 1.  Maintain regularly  Use right tool for the job  Inspect before use  Operate according to manufacturers’ instructions  Use the right.

My Career Choices By Mikey. My 1 st Choices is Automobile Mechanic.

Topic 2: The Wheel and Axle, Gears, and Pulleys

Striving For Safety Excellence HunterDouglas Corporate Environmental, Safety, Risk Management Power and Hand Tool Safety.

Revision Topics – General areas Design Process – Analysing, Designing, Evaluating, (anything linked to completing a mini coursework project within the.

Pneumatic vs. Hydraulic Systems What are Pneumatics systems? What are Hydraulics systems? What is the difference between the two?

Tractor Safety, Operation, and Maintenance

This presentation was created by the N.C. Department of Labor for safety and health training. Machinery and Machine Guarding 29 CFR – CFR.

29 CFR – CFR –244. To enable students to understand the following:  Basic concepts of machine guarding  How to identify machine.

Machine Guarding OSHA 29 CFR

Tools Hand and Power.

Hand & Power Tool Safety

Automotive Service Modern Auto Tech Study Guide Chapter 53

Motion transmission systems

DAE by Norhafiza Samion

Machine Guarding MODULE 19

Hand and Power Tool Safety

Presentation transcript:

OSHA 10 hr Training OSHA 10 hr Training Hand tools Hand tools Power tools Power tools

General requirements General requirements Condition of tools Condition of tools Guarding Guarding PPE PPE Switches Switches

Electrical-operated tools Electrical-operated tools GFCI GFCI Cords Cords

Pneumatic power tools Pneumatic power tools Hose whips Hose whips Safety clips Safety clips Muzzles Muzzles

Fuel powered tools Fuel powered tools Fueling Fueling Enclosed spaces Enclosed spaces

Hydraulic power tools Hydraulic power tools Fluid Fluid Usage Usage

Power-actuated tools Power-actuated tools Training Training Tested Tested PPE PPE

Abrasive wheels and tools Abrasive wheels and tools Guards Guards Rests Rests Requirements Requirements

Hand tools Hand tools Wrenches Wrenches Impact tools Impact tools Wooden handle tools Wooden handle tools

Wood working tools Wood working tools Switches Switches Self-feed Self-feed Guards Guards PPE PPE

Mechanical power- transmission apparatus Mechanical power- transmission apparatus Prime-mover guards Prime-mover guards Shafts Shafts Pulleys Pulleys Belt, rope, and chain drives Belt, rope, and chain drives Gears, sprockets, and chains Gears, sprockets, and chains Key, setscrews, and projections Key, setscrews, and projections Bearing and facilities for oil Bearing and facilities for oil Ect. Ect.

Being Aware Being Aware Your surroundings Your surroundings Other surroundings Other surroundings