CORE DRILLING MACHINES AND ACCESSORIES

PRINCIPLES OF DRILLING W.A.S.P. Water Anchor Speed Power

M-1 Drill Rig 2 ½" Square column with black oxidized finish 10" Bit capacity-14" with one spacer Complete Combination Angle Combo Anchor

M1AA-15 Core Rig M1AA-15 6 “ capacity Single Speed800 rpm 15A / 115V / 2.5HP Includes trap ring Vacuum plate option

M-2 Drill Rig Precision ground & chrome plated 2-7/8 square mast 10” Bit capacity - up to 36” with spacers Anchor Stands Complete Combo Combo Stands

M-3 Drill Rig Complete Combo Stand Anchor Stand Stair Rig Lightweight and Economical 360 degree swivel Complete Stair Rig Combo Stand Anchor Stand

M-4 Drill Rig 6” bit capacity Anchor Stand Swivel Stand Combo Stand Complete Combo

M-5 Drill Rig Anchor Stand Combo Stand Complete Combo

M-5 PRO

Ideal for Larger Diameter Core Drilling Jobs M-6 Drill Rig Equipped with chrome plated mast with 5-7/8” x 3-7/8” rectangular cross section that makes drilling with big bits much easier. 18-inch bit capacity with standard pillow block. Much larger bit capacity with optional spacers Heavier gear rack that can carry twice the load of our M-2 Drill Rig. Ideal for Larger Diameter Core Drilling Jobs

WEKA Drill Motors Model DK12 Hand Held 14 amp, 110V, 3-speed 580/1400/2900 rpm slip clutch Model DK22 23amp, 110V, 3-speed 300/640/960 rpm, slip clutch Model DK32 30 amp, 230V, 3-speed 380/800/1200 rpm slip clutch

WEKA Drill Motors Model DK42 Model DK52 6 amp 460V, 3 phase 3-speed Or 13 amp 230V, 3 phase 3-speed, 200/420/630 rpm, slip clutch Model DK52 8 amp, 460V, 3-phase Or 16 amp, 230V, 3-phase 160/310/470 rpm slip clutch

Weka DK13 14 amp Wet or dry 3 speed Also fits the M4 rig

Weka DK11 with Telescoping Trap Ring 120V/14A High speed - 6500 rpm M33/3 shaft for quick core removal at rear end of bit Available 1 3/8” telescopic trap ring For use on M33 bits

Weka DK16 Intellitronik™ inside! Slow Start Overload Warning (safer operation & low start-up current) Overload Warning Advanced Overload Protection Instant Restart 30% more nominal power than the DK12 same “practical” power as the DK12 with thermal overload protection Same weight and size as the DK12 (faster rotor, different gear box) / decal claiming DK16 advantages

CB500-HH Up to 3” bit capacity 2-speed 1100 and 2200 RPM Shoulder brace Fits the M-4 mount Part # 4244004

Drill Motors CB700 CB748 Milwaukee Pneumatic motors also available 20 amp, 2-speed 400/930 rpm Slip clutch CB748 20 amp, 2-speed 350/900 rpm Slip clutch Milwaukee Model 4004 – 20amp 300/600 rpm Model 4096 – 20 amp 450/900 rpm Model 4005 – 20 amp 600/1200 rpm Model 4092 – 15 amp 375/750 rpm Model 4097 – 15 amp 450/1200 rpm

Control Panels Single Switch/Amp Meter On/Off Switch Digital Dual Switch/Amp Meter Dual Switch/Amp Meter

ADAPTERS EXTENSIONS

HILTI COMPATIBLE ADAPTERS

A B C D E Hydraulic Motors Webster Motor B. Char-Lynn Motor C. White Motor D. Pillow Block & Spindle E. Flow Control Valve

Drill Rig Vacuum Bases Recommended for 8” diameter holes or less Turn machine on it back and insert vacuum seal under machine back Turn drilling machine upright and loosen the 4 leveling screws Plug cord into grounded outlet and turn pump switch on Make sure vacuum gasket is firmly in place under rig base

Vacuum Anchor Method-to-Floor Insert vacuum slot cap into anchor bolt slot and check hose connections Machine should now be vacuum anchored Adjust the 4 leveling screws to eliminate rocking After use, turn drill motor off, unplug and remove

Operating a Drill Rig Align rig for desired hole Securely anchor the rig Level the rig Select drill speed for specific size bit (never change speed while drill is spinning) Connect power and water Turn water valve on (1 to 2 gallons per minute) Turn drill on and begin to drill (full load after crown has penetrated surface) Even feed pressure

Core Retrieval Core Catcher Core Extractor

Pipe Mount Works on any core drill Easily and securely attaches rig to most pipe Comes complete with all attachments

Core Drilling Scrapbook 50” Bit on M-6 Rig

Core Drilling Scrapbook Inverted Drilling

36” diameter hole drilled at 23° angle - 8 feet deep Core Drilling Scrapbook 36” diameter hole drilled at 23° angle - 8 feet deep

Stitch Drilling (6” Diameter Holes) Core Drilling Scrapbook Stitch Drilling (6” Diameter Holes)

Small Diameter Holes With Extensions Core Drilling Scrapbook Small Diameter Holes With Extensions

Angle Drilling With Standard Stand Core Drilling Scrapbook Angle Drilling With Standard Stand

Core Drilling Scrapbook

Core Rig Team Questions T F 1. The M-1 Drill Rig has a maximum 14” bit capacity. T F 2. A combination drill stand can be anchored or vacuumed to the floor. T F 3. The M-2 Drill Rig has a capacity up to 36”. T F 4. The M-2 Drill Rig is the best model for stairs. T F 5. The M-3 Drill Rig has a 360 degree swivel mast. T F 6. The M-4 Drill Rig can be used with a 10” bit. T F 7. The M-4 Drill Rig converts to a hand held. T F 8. Our 24HG Vacuum Pump is used to pick up the water during drilling. T F 9. Our Dovetail Motor Q.D. option for the M-1 and M-2 Rigs makes motor removal fast and easy. T F 10. The vacuum plate with wheels accessory converts an anchor base to a vacuum base on the M-1, 2 & 3 rigs. T F 11. We have drilling systems available in electric, hydraulic and pneumatic. T F 12. You can stand on a drill rig base to hold it down while drilling.