CENTRIFUGAL PUMP Module 3.2 Vertical Pump Construction

Slides:

Advertisements

Similar presentations

50Hz Stainless steel Vertical multistage centrifugal pumps

Advertisements

Automotive A/C systems

Service Delivery 3 Pumps.

Range name: alifter Range code: TMA T Magnetic M Close-coupled A Self-priming (Alifter range) Name of the model: nominal Capacity (m 3 /h) 16.

ADX 150 – Engine Repair ADX 170 – Climate Controls

TYPES OF MECHANICAL SYSTEMS

Basic Refrigeration Cycle

CENTRIFUGAL PUMP Module 3.2 MCP Construction

Thermal Power Station Plant. Introduction 150 MW Thermal power station plant, produce 450t/hr steam at full load The max steam pressure is 150 bar with.

ZEEMS II Modular Fuel Systems.

Labyrinth seal into two halves

What is a centrifugal pump?

DEWATERING PUMP.

ENERGY CONVERSION ES 832a Eric Savory Lecture 11 – A small-scale power plant worked example Department of Mechanical.

Section 5: Commercial Refrigeration

HVACR 317 – Refrigeration Core

Introduction to FLUID COPLING.

HCS Series Screw Compressor Packages. 2 HCS Series.

MICE Hydrogen System Implementation Tom Bradshaw Elwyn Baynham Iouri Ivaniouchenkov Jim Rochford.

2 July Turbine Condensate System

2 July Air & Draft system

Goulds ISO Series ISO End Suction Centrifugal Pump

COMMERCIAL REFRIGERATION

HEATING AND AIR-CONDITIONING

PUMP TYPES The centrifugal pump has several characteristics:

Hydronic Mechanical Controls

Air Compressors.

TURBINE & COOLING SYSTEM Presented By – AVIJEET PRATAP 07ME12 IET AGRA

Pacific school of Engineering , surat A Presentation on

 Install new air cooled high efficiency screw chiller (variable speed)  Install new fan coils with ECM motors and low temperature heating coils and proper.

Week 1 Unit Conversions Mass and Volume Flow Ideal Gas Newtonian Fluids, Reynolds No. Week 2 Pressure Loss in Pipe Flow Pressure Loss Examples Flow Measurement.

ELECTRONIC FUEL INJECTION COMPONENTS

A Trane Air Conditioning Clinic Centrifugal Water Chillers Air Conditioning Clinic TRG-TRC010-EN © American Standard Inc

Components of Centrifugal pumps

HVAC523 Circulator Pumps.

Plan 2 – Dead-end Seal Chamber Optional Jacket

ESS Cryogenic Distribution System for the Elliptical Linac MBL/HBL - CDS requirements Preliminary Design Review Meeting, 20 May 2015, ESS, Lund, Sweden.

PLUMBING Presentation on Central Heating – Pump Position.

C.R.ENGINEERING COLLEGE

Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation Driving the worldUIG / mlr / Basic Product Training 2003 Only for Internal.

Pumps Unit 10. Learning Objectives TLW be able to describe the following about pumps used in the process industry: –Types –Uses –Operation –Monitoring.

Centrifugal Compressor LEI ZHOU MMAE UCF. Spec. of top cycle compressor Pr=2.42 Working fluid: Neon Mass flow rate: 0.51 kg/s Inlet pressure: 2 atm Inlet.

Analysis of Axial & Centrifugal Compressors To be Selected as per Specific Speed of Applications…. P M V Subbarao Professor Mechanical Engineering Department.

WILO MVI Vertical Multi-Stage Pumps Multi-Stage Pumps for Commercial, Municipal and Industrial Applications Presentation Date – Revised Sept 2006.

CHILLED WATER AIR-CONDITIONING SYSTEMS

Week 1 Unit Conversions Conservation of Mass Ideal Gas Newtonian Fluids, Reynolds No. Pressure Loss in Pipe Flow Week 2 Pressure Loss Examples Flow Measurement.

HEAT PUMPS Efficiency and Technology By: Aakash Harpalani.

1 Small Coolers for MICE Michael A. Green University of Oxford Department of Physics Oxford OX1 3RH, UK MICE Collaboration Meeting RAL.

1.8 K cycle and specificities CC: - 3D wheels - Bearings (300K) HX: - Very Low Pressure “Mixed” Compression P ratio ≈ 80 HX Stainless Steel Plate Axial-centrifugal.

Chapter 5 Light vehicle engine systems © Pearson Education Ltd Copying permitted for purchasing institution only. This material is not copyright.

Refrigeration What's Refrigerated? What makes up a system?

A two-stage system for the future cooling system.

Prepared By Rohit G. Sorte M.Tech

Fluid Mechanics for Chemical Engineers Arif Hussain (Lecturer)

Advantages of Rotating Machines Less balancing problems Low lubricating oil consumption Higher reliability.

Sorbent Handling Plant by NHI-Design & Equipment Specifications

M1M3 Fan Coil Unit Status Gary Muller & Brian Johnson LSST 2017 Project & Community Workshop 8/17/2017.

Endsuction Pumps Model LS

PNEUMATICS Chapter 3 ROTARY COMPRESSORS

Auxiliary Engines Pumps Winches Steering engine Boilers Generators

System One Pumps S1-101 Construction and Features

Air Distribution Control

How Do Hot Tubs Work?.

Course PEF3006 Process Control Fall 2017 Actuators By Finn Haugen

EXECUTIVES & NON-EXECUTIVES

Axial Booster Fans System

Axial Booster Fan System

ENERGY CONVERSION ES 832a Eric Savory

Presentation transcript:

CENTRIFUGAL PUMP Module 3.2 Vertical Pump Construction www.cryostar.com contact@cryostar.com

Various applications: Main Uses are: Air separation Liquefaction plants. Various applications: Internal compression Crude argon recycling Re-injection Back-up

VP 8/145/4L-3,0 C/0 Reminders Labyrinth Impeller Material diameter 8 stages Speed*100 Impeller tipwidth Vertical

Principles Vertical pumps divided in Three parts: Cold End Warm box or Intermediate piece Motor Side Single and Multi stage pumps Cold box installation with thermal barrier All seal types available Cold end with direct coupled motor. Synchronous speed (50/60Hz) or variable speed

VP construction Drive shaft with coupling Shaft seals : Labyrinth Mechanical Gas seal Dual Gas seal Total mass supported by mounting flange

Construction: Warm box (Intermediate piece on VP) Outlet of the labyrinth heating coil grease retainer chamber coupling leak detector Le serpentin sert à vaporiser le mélange N2 et fluide qui pourrait encore être sous forme liquide

Construction: Warm box (cont’d)

Construction: Warm box (cont’d) Heater on motor side

Construction: Cold end inducer diffusor impeller outlet vent inlet

Construction: Cold end (cont’d)

Construction: Cold end (cont’d)