Procedure Editor

:17 This SOP describes the Setting procedure and order folders. How to load procedures in order files for sources and destinations. The definition of dilutor solvents used. The differences between “Bruker” and “Custom” procedures. How to add and edit procedures and sub-procedures. Introduction

Procedure Editor :17 This button is used to change the procedure export directory path. Check the correct procedure export path. The directory contains all procedures for the “Create order dialog“ window. Edit Settings

Procedure Editor :17 Open the procedure editor dialog The procedures can be defined here and will be used later to set up orders within the following applications: PrepGilsonST “Create order dialog“ SampleTrack Procedure Editor Dialogue

Procedure Editor :17 Procedures defined and saved here… … can be selected later in the “Create order dialog“. 1a. Using Procedure in Order files

Procedure Editor :17 Placeholder variables for SOURCE Samples defined here… … can be selected later when setting up orders in the “Create order dialog“. 1b. Using Procedure in Order files: Source

Procedure Editor :17 Dispenses defined here… (the DESTINATION position variable in the Order file will be used!) … can be selected later when setting up orders in the “Create order dialog“. 1c. Using Procedure in Order files: Destination

Procedure Editor :17 Placeholder variable for a Dilutor/ValveMate solvent defined here… (selection „##$SOLVENT Variable in Order “) … can be selected later in the “Create order dialog“. 1d. Using Procedure in Order files: Dilutor Solvent

Procedure Editor :17 Procedures of the type “Bruker“ cannot be saved. The “Save“ button is gray. Save the procedure with the button “Save As“ and use a different personalised name like “my procedure“. Open the “Saved as“ procedure. It has the custom symbol and can be modified and saved. 2. Procedure Difference: “Bruker“ / “Custom“

Procedure Editor :17 After opening the new procedure it will be displayed as a “Custom“ procedure. 2a. View a “Custom“ Procedure

Procedure Editor :17 Use this button to load procedures (only for procedures of type “ADD“) 2b. Open Procedure

Procedure Editor :17 Click on the “Source Type“ of any line to select it and show all values in the line edit area. 3. Show Procedure Values

Procedure Editor :17 2. Press the button “Update“ to set the new values in the selected line. 1.Enter the parameters for the solvent at the Dilutor / ValveMate. 4a. Edit the Source Type “Solvent at Dilutor“

Procedure Editor :17 4a. Edit the Source Type “Solvent at Dilutor“ Select the solvent name from the list. Tip: For each solvent name in the list the position on the ValveMate is predefined in the configuration.

Procedure Editor :17 2. Press the “Update“ button to set the new values in the selected line. 1. Enter the gas gap parameters. 4b. Edit the Source Type „Gas Gap“

Procedure Editor :17 2. Press the “Update“ button to set the new values in the selected line. 1.Enter the sample parameters ( = Source in the order file). 4c. Edit the Source Type “Sample“

Procedure Editor :17 2. Press the “Update“ button to set the new values in the selected line. 1.Enter the parameters for the tray solvent. 4d. Edit the Source Type “Solvent in Tray“

Procedure Editor :17 Select the solvent name from the list. Tip: For each solvent name in the list the position in the tray is predefined in the configuration. 4d. Edit the Source Type “Solvent in Tray“

Procedure Editor :17 1. Check the type of subprocedure. 2.Select the name of the subprocedure (all files of subdirectory...\Disp\ are listed ). 5. Adding Subprocedures to a Line

Procedure Editor :17 A procedure with the type “Dispense“ will be opened. 5a. Editing a Subprocedure Type “Disp“

Procedure Editor :17 A procedure with the type “Mix“ is opened. 5b. Editing a Subprocedure Type “Mix“

Procedure Editor :17 A procedure with the type “Clean“ is opened (Save as a Custom procedure to edit). 5c. Editing a Subprocedure Type “Clean“

Procedure Editor :17 1. Select a line from the list. 2. Modify the values as required. 3. Use the “Add below“ button to insert a copy of the current line. 6. Adding Lines

Procedure Editor :17 5. Press the “Paste below“ button. 1. Select a source line from the list. 2. Modify the values as required. 3. Use the “Copy“ button to copy the current value area. 4. Select a location to paste the new data. 7. Copying and Pasting Lines

Procedure Editor :17 Use the “Delete“ button to remove the selected line from the list. 8. Deleting Lines

Procedure Editor :17