Measurement and Sizing. Definitions Rough sawn timber Timber which is straight from the saw Used for fence palings, construction, pallets, packing cases.

Slides:



Advertisements
Similar presentations
Objective Use agricultural mechanics tools properly and safely.
Advertisements

Woodwork Joints 2.
Characteristics of Wood and Squaring stock
Lumber Grading.
PLANNING FACE GRAIN JOINTING EDGES STRAIGHT AND SMOOTH CUTTING RABBIT JOINTS CUTTING CHAMPFERS AND BEVELS.
Clay Wind Chimes Slab Pottery with Incised Fossil Designs.
S3 Standard Grade C & D Woodwork Machine Tools. Next Slide >< Previous Slide Mr A. Atkinson Circular Saw Machine 1Machine 2 Bandsaw.
THE EFFECTS ON THE MANUFACTURING OF COFFINS AND CASKETS.
Chapter 2 Lumber Carpentry First Canadian Edition
Match the number and the pattern from the coded table below with the letters from the table to reveal the class topic. Example 3
Timber - the Material Timber grows on Trees Properties of Timber Grading sawn timber Durability of timber Specifying and handling timber Application of.
Wood Products Lumber Measurements Calculations
Woodwork Planes. Plane Parts Smoothing Plane The Smoothing Plane is generally used for fine finishing and planning wide flat boards (like table tops)
Chapter 21 Processes Used to Separate Wood Materials.
 Key Learning ◦ There are many important factors to take into consideration when choosing the type of lumber.  Unit Essential Question ◦ What considerations.
How to prepared the cross halving joint with basic hand tools
 Hardwood (Deciduous) - Reproduce by encased nuts and seeds  Softwood (Coniferous) - First trees - Reproduce by seed on their cone  Misleading?
Chapter 2 Lumber.
Suzanne Chludzinski ILS The Basic Elements of Geometry
Building a clock PART 1: The Body. Gathering materials  The wood that you will be using is called Maple. You can identify it by knowing that it is: Heavy.
Surface Area of Prisms Unit 5, Lesson 2. What is a Prism? Definition: –A three dimensional figure with 2 congruent polygon bases and rectangular sides.
BE PREPARED TO TAKE A FEW NOTES TODAY… Pick up the pink sheet at the front.
Building the Footstool P R O J E C T O V E R V I E W.
Selecting, Cutting, and Shaping Wood
Product Design AQA GCSE
► A point is the place where two lines intersect. ► We identify this point with a number or a CAPITAL letter. ► A point has no length or width, it just.
Selecting Wood and Lumber Mr. Rodriguez Ag Mechanics.
Stock Preperation Warm-Up. Explain the difference between the USE of the JOINTER and the SURFACE PLANER.
Table Saw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.
RABBET JOINT The Rabbet Joint is: an L-shaped cut along the end or edge of a board. a wood joint that can be built with hand or power tools. formed by.
Warm-Up Explain when you would use the Belt/Disc sander versus the Oscillating Spindle Sander.
Surfacing Rough Lumber Woodworking 2,3,4. Materials Surfacing Rough Lumber Worksheet Tape Measure Square –Combination –Tri-Square Scrap Lumber.
Woodwork Joints Introduction This unit will introduce various woodworking joints. You will be asked to manufacture some commonly used joints. Assessment.
Section 9.1 Arc Length. FINDING THE LENGTH OF A PLANE CURVE Divide the interval [a, b] into n equal subintervals. Find the length of the straight line.
Homework: Use the information that you gathered this week to draw out your plan view working drawing, 1:1 scale. Use sheet 6. Hand in next week. Start.
Wood.
Agriculture Mechanics I.  Linear ◦ Comes from the word line.  Linear Measure ◦ The measurement of lines ◦ A line is the distance between two points.
TAKE NOTE ON THE ORDER OF PROCEDURE FOR CONSTRUCTION OF THE LAMINATE COUNTERTOP. Countertop Procedures.
The cutting list should contain the following data: 1. PART No. I.e. 1, 2, 3, etc. 2. NAME a description of the part, eg. top 3. QUANTITY required, e.g.
Square Plant Stand. TOOL: Radial Arm Saw NEXT STEP: Surface Planer RESULTS: Rough size pieces for 4 Legs. 33” long PROJECT Square Plant Stand PART Legs.
Lesson 5.  The carpentry trade covers many items. That is, it is not confined to a few specific items such a reinforcing steel, painting etc.  Common.
Cones.  Cones are shapes that have a circular base and come to one point at the top.
Recognition and use of hand tools. Can you name and state typical uses for this marking-out tool? 1 This is a try square. It can be used to mark lines.
Cutting and shaping wood BDHS Plain-sawed or Plain sawn Lumber – most economical and least wasteful.
Recognise basic woodworking joints. 1 Can you name and state a use for these joints? These are angled butt joints, which can be used for the simple jointing.
Cones. Cones are shapes that have a circular base and come to one point at the top.
Bandsaw. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in the.
Wood is a hard, compact, fibrous, material It is made up of the material that carries food and nutrients in the tree. Xylem carries material up from the.
State Practice Exam Wood Characteristics.
Common Types of Wood AG Mech I Standard 6:1-3.
BASIC DESIGN AND TECHNOLOGY
Wood Products Lumber Measurements Calculations
Rip vs. Cross-Cut Rip – cuts along the wood grain
Table Saw.
Selecting, Cutting, and Shaping Wood
Timber processing and assembly
BAND SAW CHAPTER 24.
Selecting, Cutting, and Shaping Wood
Timber Conversion J.Byrne 2012.
Racial Determination using Skull
5 Construction 2 Perpendicular Bisector of a Segment, Using Only Compass and Straight Edge Draw a line segment [CD]. Place the compass needle point on.
Vocational school Jean De Berry
Oblique Sketches (Material developed by Project Lead the Way)
Understanding Lumber & Identifying Materials
How to Pin and Tack Fabric
AQA GCSE 2 Working with timber based materials and fixings
Points, Lines, Planes and Segments
“Cutting Parts to Size Vocabulary”
PAULOWNIA PRIMED WOOD TRIM & PATTERN
WOOD SUPPLY Seasoning wood
Presentation transcript:

Measurement and Sizing

Definitions Rough sawn timber Timber which is straight from the saw Used for fence palings, construction, pallets, packing cases

Definitions Dressed timber Timber which has been machine- planed smooth from rough sawn. DAR Dressed all round Timber that has been dressed on all sides and edges. Cabinet timbers, mouldings, architraves D2S Timber dressed on 2 sides only

Timber Sizing Timber comes in a range of sizes So that people understand what is going on there is a standard for stating timber sizes Timber sizes is given by WIDTH x THICKNESS x LENGTH Width: Thickness: measured across the grain on the face measured across the grain on the edge Length:measured along the grain

Available Sizes Radiata Pine Kiln Dried Dressed All Round Finish Sizes Thickness Width x     19x    35x   42x  45x   70x  90x 