CLIQ unit Integration. General view: -Schroff rack 19’’ 25U (500mm x 600mm x 1120mm). -2 fixed wheels +2 castor wheels with brake ⦰100mm. Capacitors Capacitors.

Slides:

Advertisements

Similar presentations

Basic Circuits TEST YOUR BRAIN!.

Advertisements

4/22/ MAKING YOUR ROBOTS SEE Building and Testing Photosensitive eyes.

Ryan Roberts April 2, Background The tool I am building will be used by me on my dads stock car team. I have a tool already that I use to measure.

Engineer Training Rear Operation Unit TJ8300 / TJ8500 Rear Operation Unit.

Indian Institute of Technology Hyderabad Railway Level Crossing Lights By: Returaj Burnwal Kunal Raunak Dhananjay Kr. Gupta Krishna Kumar.

1 Electronics and Control Technology. 2 Electronics and Control The 555 timer is an 8-Pin D.I.L. Integrated Circuit or ‘chip’ What it looks like Notch.

ST/PRM3-EU | | © Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying.

SE207 Modeling and Simulation Lab # 3: Analog Simulation of a First Order System (RC circuit)

Chapter 4 AC to AC Converters

Lightning Detector Michael Bloem December 5, 2002 Engr 311.

TEST YOUR BRAIN! Components.

Presentation Topic 4 Way Traffic Lights.

CLIQ power supply Integration. General view: -Schroff rack 19’’ 25U (500mm x 600mm x 1120mm). -2 fixed wheels +2 castor wheels with brake ⦰100mm.

TE-MPE-EE, 02-Apr CLIQ Power supply design J. Mourao TE-MPE-EE.

 Salient characteristics / Approvals  Non-illuminated Switches  Illuminated Switches  Pilot Lights  Contact Elements Control & Signalling Devices.

1 Light OP 504 ex – Project Presentation Luca Invernizzi Design.

TE-MPE-EE, 16-Apr CLIQ Power supply design J. Mourao TE-MPE-EE.

Ch4 Electronic Components Circuit/Schematic Symbols.

1 Applied Control Systems Technology. 2 Pin configuration Applied Control Systems.

Segway Controller Notes. = connection on top layer of circuit board = connection on bottom layer of circuit board Ground Plane: Areas enclosed by the.

Electronics: Intro Quantities: Voltage Current Power Devices: Resistor Capacitor Inductor LED Transistor Op-Amp Laws: Ohm’s Law Kirchhoff’s Laws.

Control Angle via Button Pushes One button increases angle. Other decreases angle. Both light LED.

Measuring the Current and Voltage of a 820 Ω Resistor Setting for Multimeter = 200 mA DC Measure Voltage in 2 V increments up to 20 V.

KeypadFunctionDescription A Accelerator Accelerate Speed B Brake Decrease Speed C Cruise On Turn on cruise system * + Increase speed # -Decrease Speed.

The energy change in a thermocouple is : 1.E E to E H 2.E S to E E 3.E L to E E 4.E H to E E :20.

Electronic Components Circuit/Schematic Symbols. RESISTOR Resistors restrict the flow of electric current, for example a resistor is placed in series.

Electronic Parts.

MICE RF System Power Supplies, Control and Monitoring Status report February 2012 Chris White, STFC Daresbury Laboratory MICE Collaboration Meeting CM32,

ELECTRONICS An electronics system has 3 parts – input, process, output.

User Interface – Switch Panel 6 Gang Switch Panel Configuration guide RS485 Terminal Fixing hole Bayonet Front ViewBack View.

Main contacts closed – RED Colour with ON

The Basics Electronics. To familiarise yourself with electronics To have an understanding of how and why we test electronic circuits. To complete a test.

18240 Element two - Components INPUTS OUTPUTS PURPOSE TYPICAL USE.

7. Direct Current circuits. 11 Find the currents, which flow in all the wires of the circuit in this figure 12  9 V 6 V b a cd 18 

BLDC Motor Speed Control with RPM Display. Introduction BLDC Motor Speed Control with RPM Display  The main objective of this.

BPT SpA Via Roma 41, Cinto Caomaggiore Venezia, Italy 1 OPHERA NEW BPT VIDEO RECEIVER HANDS-FREE COLOUR VIDEO RECEIVER (RECESSED MOUNTED)

Controlling Home Appliances Using Voice. Controlling Home Appliances Using Voice Introductio n  Home automation has an important.

ARM CORTEX (STM32) BASED MOTOR SPEED CONTROL SUBMITTED BY EDGEFX TEAM.

CAPACITANCE METER Tests capacitors from 1p to 10u, in 6 ranges.

MAGNETIZING ELECTRICAL-ELECTRONIC EQUIPMENT 800V, 1200A

Circuit Simulation Training

Single Speed Technical features 5 Speed Wheel dimension: 700 C

MICE RF System Power Supplies, Control and Monitoring Status report

Cordless Electric Nailer

POWER AMPLIFIERS NLB 60E LAB.GRUPPEN NAME MODEL 제조사 Network connectors

Light Detection Circuit

Design of new generation CLIQ units (CLIQ2)

COMP211 Computer Logic Design Introduction to the DE2 Board

EPR = Electronic Products and Relays

Uninterrupted Power Supply

Transistor & Voltage Divider

Chapter 2 Push button and Potentiometer

The resistance of a thermistor changes from 30k to 12k when the temperature changes from 20C to 70 C Calculate the sensitivity if resistance is taken.

Lesson 14: Introduction To Sequential Control

4 channels, each as input or output

2 channels, each as input or output

ET 438B Sequential Control and Data Acquisition

Universal Interface, 12-fold, FM US/U 12.2

Universal I/O Concentrator UK/S 32.2

Raspberry Pi with Pibrella

What charge exists on a 30 μF capacitor (fully charged) with a 120 V potential difference between its plates and what is the energy stored? Ans: 3.6.

Basic Electronics Part Two: Electronic Components.

Lab 1. Introduction to the DE2 Board

CECOM LAR Tropo Operation Course

Electronics: Intro Quantities: Voltage Current Power Devices: Resistor

Lab 1 Components List.

Lecture 4. Introduction to the DE2 Board

6. USING THE TDR200 IN ANALOGUE MODE

Example Example 1: An electric lamp is rated 110 W, 200 V. When the lamp is operated at its rated power and voltage, calculate a) the current flowing through.

2019 Investing Now Summer Program

Presentation transcript:

CLIQ unit Integration

General view: -Schroff rack 19’’ 25U (500mm x 600mm x 1120mm). -2 fixed wheels +2 castor wheels with brake ⦰100mm. Capacitors Capacitors

Command: 3 Light Mains indicator Light Mains ON-OFF SDS Power supply with Green led “End of charge” Red led “Ucap>40Vdc LCD Current indicator LCD Voltage indicator Selector 0-500V SDS Power supply with Green led “End of charge” Red led “Ucap>40Vdc LCD Current indicator LCD Voltage indicator Selector 0-500V Push button Start charging Push button Start charging Equipment stop Light Mains indicator Light Mains ON-OFF Selector 40mf or 80mf

Rear panel: Mains input Trigger input Output voltage

Control crate:

6 Thyristors and pulse transformer:

7 Resistors bank:

8 Output voltage and selector capacitors: