Redox in Magmatic Systems Activities in Non-Ideal Solutions Lecture 10

Line 5 has a slope of -1 and an intercept of log K. We can also use pe-pH diagrams to illustrate stability of solid phases in presence of solution. In this case, we must choose concentration.

More about pe-pH diagrams pe-pH diagrams are a kind of stability or predominance diagram. They differ from phase diagrams because lines indicate not phase boundaries, but equal concentrations. o There is only 1 phase in this this diagram – an aqueous solution. Regions are regions of predominance. o The aqueous species continue to exist beyond their fields, but their concentrations drop off exponentially.

Environmental Interpretation of pe-pH

Redox in Magmas

Oxygen Fugacity Igneous geochemists use oxygen fugacity ƒ O 2 to represent the redox state of the system. Hence, the oxidation of ferrous to ferric iron would be written as: 2FeO + O 2(g) = Fe 2 O 3 For example, oxidation of magnetite to hematite: 2Fe 3 O 4 + ½O 2(g) = 3Fe 2 O 3 (Actually, there isn’t much O 2 gas in magmas. Reaction more likely mediated by water and hydrogen).

Redox in Magmatic Systems For magnetite-hematite 2Fe 3 O 4 + ½O 2(g) = 3Fe 2 O 3 assuming the two are pure solids At a temperature such as 1000K

Oxygen Fugacity Buffers The log ƒ O 2 – T diagram is a phase diagram illustrating boundaries of phase stability. The two phases coexist only at the line. Reactions such as magnetite-hematite (or iron- wüstite or fayalite- magnetite-quartz) are buffers. For example, if we bleed O 2 into a magma containing magnetite, the ƒ O 2 cannot rise above the line until all magnetite is converted to hematite (assuming equilibrium!)

Real Solutions: Minerals and Magmas Chapter 4

We will cover Chapter 4 only through section 4.6 (page 144). You will not be responsible for the remaining material in the chapter.

Power of Solutions Our thermodynamics would be so much simpler if all solutions behaved ideally! Even simpler if there were no solutions at all! But, once we learn how to handle them, we’ll see that we can use solution behavior to do some real geochemistry and learn things about the Earth. o Because the distribution of Mg and Fe between olivine and a magma depends on temperature, we can use the observed distribution to determine magma temperatures. o We can predict the temperature at which K- and Na-feldspar will exsolve and use this to determine metamorphic temperatures. o We can actually predict the plagioclase-spinel peridotite phase transition o We can determine equilibration temperatures of garnet peridotites.

In This Chapter We’ll learn how to handle non-ideal solutions Learn how to construct phase diagrams from thermodynamic data Learn how thermodynamics is used for geothermometry and geobarometry See how thermodynamics can be used to predict the sequence of minerals precipitating from magma.

Non-Ideality We found a useful approach to non-ideality in electrolyte solutions (Debye-Hückel), but there are many other kinds of non-ideal solutions, including solids, liquid silicates, etc. Some substances undergo spontaneous exsolution (oil and water; K- and Na-feldspar; clino- and ortho- pyroxene; silicate and sulfide magmas). When that happens, we know the solution is quite non-ideal (ideal solutions should always be more stable than corresponding physical mixtures).

Margules Equations When you need to fit an empirical function to an observation and don’t fully understand the underlying phenomena, a power series is a good approach because it of its versatility. So, for example, we can express the excess volume of a solution (e.g., alcohol and water) as: where X 2 is the mole fraction of component 2 and A, B, C, … are constants, Margules parameters, to be determined empirically (e.g., by curve fitting).

Symmetric Solutions Let’s first look at some simple cases. One such case would be where we need only the first and second order terms. The excess volume (and other excesses) should be entirely functions of mole fraction, so for a binary solution where X 1 = 1 - X 2, A= 0 and our equation should reduce to: The simplest such case would be symmetric about the midpoint X 1 = X 2. In that case, Substituting X 1 = 1 – X 2, we find that B = -C

Interaction Parameters Let W V = B W is known as an interaction parameter (volume interaction parameter in this case) because non- ideal behavior results from interactions between dissimilar species. The interaction parameter is a function of T, P, and the nature of the solution, but not of X. We can define similar interaction parameters for free energy, enthalpy, and entropy. or

Regular Solutions Since ∆G = ∆H-T∆S The free energy interaction parameter is: W G = W H – TW S Regular solutions are the special case where W S = 0 and therefore W G = W H and W G is independent of T. o what does this imply about ∆S excess ?

Interaction Parameters and Activity Coefficients For a binary symmetric solution, λ 1 must equal λ 2 at X 1 = X 2. From this we can derive: For X 2 ≈ 1 (very dilute solution of X 1 ), then andW G = RT ln h What happens when X 1 ≈ 1?

Asymmetric Solutions More complex situation where expansion carried out to third order. Excess free energy given by: Activity coefficient: Calculated Free Energy at 600˚C in the Orthoclase-Albite System as a function of Albite mole fraction.

Albite-Orthoclase Free Energy at various TA 3-D version

G-bar–X and Exsolution We can use G-bar–X diagrams to predict when exsolution will occur. Our rule is the stable configuration is the one with the lowest free energy. A solution is stable so long as its free energy is lower than that of a physical mixture. Gets tricky because the phases in the mixture can be solutions themselves.

Inflection Points At 800˚C, ∆G real defines a continuously concave upward path, while at lower temperatures, such as 600˚C (Figure 4.1), inflections occur and there is a region where ∆G real is concave downward. All this suggests we can use calculus to predict exsolution. Inflection points occur when curves go from convex to concave (and visa versa). What property does a function have at these points? Second derivative is 0. Albite-Orthoclase

Inflection Points Second derivative is: First term on r.h.s. is always positive (concave up). Inflection will occur when

Spinodal Actual solubility gap can be less than predicted because an increase is free energy is required to begin the exsolution process.