INSPECTION AND ACCEPTANCE CRITERIA. PRODUCT CONFORMANCE Dimensional conformance - within tolerances as defined on product drawing Dimensional conformance.

Slides:

Advertisements

Similar presentations

IND 205 Auditing a Contractors Property Management System TLO #9 Auditing a Contractors Property Management System.

Advertisements

Definition of the KPI Return rate. Purpose This document defines the KPI return rate for suppliers of direct material. The purpose is to measure our supplier.

Sampling Inspection.

Quality Assurance System

Acceptance Sampling for Attributes Statistical Quality Control

©© 2013 SAP AG. All rights reserved. Quality Assurance (Unplanned Inspections) Scenario Overview Initiating Inspections Processing Inspections Scenario.

Quality Management System

Overview Lesson 10,11 - Software Quality Assurance

Quality Management Dr. S.W. Poon. Quality Management Introduction Meaning of quality Quality Control (QC) Quality Assurance (QA) Differences between QC.

Project Management Quality Management* Dr. Khalid S. Husain * 07/16/96

Quality Control/Quality Assurance Quality Assurance……. ….encompasses both quality engineering and quality control Quality Assurance is……. …..the application.

Statistical Process Control

GLAST LAT ProjectTEM &TEM-PS Manufacturing Readiness Review – September 16, 2004 GLAST Large Area Telescope: Performance & Safety Assurance Pat Lujan TEM.

Quality control of raw materials In-process control

Chapter 11 Quality Control.

External Defibrillators: Recalls, Inspections, and the Quality System Regulation Melissa Torres Office of Compliance December 15, 2010.

© 2009 Michigan State University licensed under CC-BY-SA, original at Corrective Action.

Ships in Service Training Material A-M CHAUVEL QMS Terms & Definitions 2009.

Six Sigma Green Belt Project

Inspection Issues in the Analytical Laboratory: An FDA Perspective Yvonne McKnight Chemist US Food and Drug AdministrationPhone: x

9/17/2015IENG 486 Statistical Quality & Process Control 1 IENG Lecture 18 Introduction to Acceptance Sampling, Mil Std 105E.

Quality Cost Quality Cost- those cost associate with the non achievement of product or service quality. Types Prevention Cost –Planning, Document, Control,

COMPANYWIDE ASSESSMENT OF QUALITY

Lecture #9 Project Quality Management Quality Processes- Quality Assurance and Quality Control Ghazala Amin.

Project Management Gaafar 2006 / 1 * This Presentation is uses information from PMBOK Guide 2000 Project Management Quality Management* Dr. Lotfi Gaafar.

Specification of niobium sheets 031/05/2010 O. Capatina G. Arnau Izquierdo W. Weingarten S. Atieh.

Quality and Operations Management

FACULTY OF ENGINEERING DEPARTMENT OF CIVIL ENGINEERING FALL SEMESTER ASSOC.PROF.DR. İBRAHİM YİTMEN CIVL 493 CONSTRUCTION MANAGEMENT.

1 LHC-DFBX Fabrication Oversight Plan Joseph Rasson LBNL Presented at the DFBX Production Readiness Review October 2002, LBNL Brookhaven - Fermilab.

Presented by Dr. Joan Burtner Certified Quality Engineer Associate Professor and Chair, Department of Industrial Engineering and Industrial Management.

ASSOC.PROF.DR. İBRAHİM YİTMEN

RBSP Radiation Belt Storm Probes RBSP Radiation Belt Storm Probes RBSP/EFW CDR /30-10/1 100 EFW DFB Systems Assurance Trent Taylor LASP.

Project Quality Management Ghazala Amin. 2 Project Quality Management Reference study materials –A guide to the Project Management Body of Knowledge (PMBOK.

The Cost of Quality Presented by Dr. Joan Burtner Certified Quality Engineer Associate Professor of Industrial Engineering and Industrial Management Mercer.

GLAST LAT ProjectFebruary 10, 2004 R. Johnson Tracker MCM Production Readiness Review 1 LAT QA has hired a full-time on-site representative (Donald Knaepple)

DIMENSIONS OF MANUFACTURING AND SERVICE QUALITY. The various dimensions of product and service quality are Performance Features Conformance Reliability.

PowerPoint Authors: Susan Coomer Galbreath, Ph.D., CPA Charles W. Caldwell, D.B.A., CMA Jon A. Booker, Ph.D., CPA, CIA Cynthia J. Rooney, Ph.D., CPA Copyright.

Section 5 Control Charts. 4 Control Chart Applications Establish state of statistical control Monitor a process and signal when it goes out of control.

Corrective and Preventive Action

9.0 Nonconforming Product Lifecycle Anyone Problem Identification Step-1 InitiateOpenClosed Quality Reporting – Across Process MRB Case MRB Analysis &

Key Performance Indicators will: Provide performance measurements for all core processes. Add value for our customers and the company. Support company.

INGAA Quality Management Systems White Paper Supporting Pipeline Construction.

WORKSHOP ON ACCREDITATION OF BODIES CERTIFYING MEDICAL DEVICES INT MARKET TOPIC 9 CH 8 ISO MEASUREMENT, ANALYSIS AND IMPROVEMENT INTERNAL AUDITS.

S. Barbanotti - DESY Requirements Conformance for SRF Cryomodules Workshop 16/10/2014 – ESS, Lund XFEL cryostat main components: Quality Assurance and.

11T Quality Assurance O. Housiaux, R. Berthet, S. Menu, R. Principe 3rd International Review on the 11T dipoles at collimator Section for the HL-LHC 6-8.

LESSON 2 Statistical Sampling

Project Quality Management

AND AFTER INSTALLATION Technical Director, NASSCO

Quality assurance for Manufacturing Dressed Cavities for SPS prototype cryomodule C. Parente (HL-LHC Technical Quality Officer) Date:

9.0 Nonconforming Product Lifecycle

Cost of Quality APPENDIX 1A.

Missing data General : Dutch Inspection checked report twice

Cost of Quality Appendix 2B.

Quality Assurance (Unplanned Inspections) Scenario Overview

ارائه كننده : محمودرضا طاهري

Appearance Approval Report (AAR)

First Article Inspection Report (FAIR) Training

Responding to a Ford Service Quality Rejection

Quality Control training

GLAST Large Area Telescope:

Chapter 11 Production.

ارائه كننده : مهدي كريمي

GLAST Large Area Telescope:

Project Quality Management

Chapter 11 Quality Control.

ESSI CHANGE AND nonconformity control SYSTEM

Fiber Reinforced Polymer Systems

Presentation transcript:

INSPECTION AND ACCEPTANCE CRITERIA

PRODUCT CONFORMANCE Dimensional conformance - within tolerances as defined on product drawing Dimensional conformance - within tolerances as defined on product drawing Structural conformance - defined by "Acceptance Criteria" Structural conformance - defined by "Acceptance Criteria"

PROCESS SPECIFICATION FOR VISUAL INSPECTION OF COMPOSITE PARTS link to document link to document link to document link to document

NONCONFORMING (REJECT) PART Quality Assurance applies acceptance criteria during in-process inspection, final inspection, and/or field inspection → part may be discrepant (defective) and rejected Quality Assurance applies acceptance criteria during in-process inspection, final inspection, and/or field inspection → part may be discrepant (defective) and rejected Discrepancy report (DR) written Discrepancy report (DR) written Requires disposition (in accordance with standard repair procedure or by MRB/Engineering) Requires disposition (in accordance with standard repair procedure or by MRB/Engineering) Part to be Part to be –reworked –repaired –scrapped