INAlA TECHNOLOGIEs Installation Training: ECS (Equipment Communications System) ECS-L2 Commissioning Version 1.0

Commissioning: ECS-L Procedure ECS-L2 Commissioning Commissioning: ECS-L Procedure

ECS-L2 - commissioning SAM Training ECS-L2 Communication Cable: A “USB Printer cable” must be used between the ECS-L2 and the computer. Once Connected open the “ECS2 ECT” software. Click on USB and Login Port Settings SAM2 & Access Control = Physical port 1 – Virtual Port 301, Baud rate 9600 L&G = Physical port 2 – Virtual Port 309, Baud rate 19200 SAM1.5 = Physical port 3 – Virtual Port 310, Baud rate 19200. Rectifier = Physical port 4 – Virtual port 302, Baud rate depends on type of Rectifier. Generator = Physical port 5 – Vittual port 304, Baud rate depends on type of Generator. LED Indications LED 1 on = GSM Network found and Logged onto GPRS Setting up of the unit: Power unit on Connect using the “ECS2” ECT Set-up the communication ports for the devices you are connecting to it Set-up the Sever IP address and APN – Customer Dependent Click on “update unit” after making a change to save the configuration to the unit. Check that LED1 is on to indicate that it is logged onto GPRS and the APN – Customer Dependent. Call to commission site with representative. *Note – Check following slide for detail information of above procedure SAM Training

ECS-L2 – Physical Port Numbers * The physical port that is connected to the SAM must be selected as the “Event PORT” PORT 1 - RS485 PORT 2 – Isolated RS485 PORT 3 - RS232 USB PORT – ECS2 ECT Port GND +12vdc 12VDC Power PORT 4 – RS232 PORT 5 - RS232 SAM Training

Software for ECS-L2 (Equipment Communication Controller-light) Communication Controller Software (ECS2 ECT): ECT Version is viewed on the top left corner as indicated with the yellow circle EG: “ECS2 ECT V 1.4” Firmware Version is viewed on the bottom as indicated with the Red circle EG: “Build: 1.4” IP address is automatically allocated to sim card and is displayed. Enable: GPRS Modem Input APN name – Customer Dependent Input Server IP for applicable operator and UDP - Customer Dependent Set Port configuration Click on Update unit Wait for unit to complete updating SAM Training

Equipment Communication Controller – Port & server allocations Virtual Port Allocations 301 SAM2 or SAM3 and Access Control 302 Rectifier A 303 Rectifier B 304 Generator 305 AVR 306 BMON 307 Fuel Cell 1 308 Fuel Cell 2 309 Energy Meter / Fire System 310 SAM 1.5 REC Vodacom Server Name Vodacom UDP Server IP UDP Server Port ZABLV06101 - CEN 10.121.5.165 299 ZABLV06102 - EAS 10.121.5.153 ZABLV06103 - LIM 10.121.5.154 ZABLV06104 - MPU 10.121.5.155 ZABLV06105 - SGC 10.121.5.156 ZABLV06106 - SGS 10.121.5.157 ZABLV06107 - WES 10.121.5.158 NGA Existing Server 10.102.242.202 Telkom Server Name Telkom UDP Server IP UDP Server Port 10.149.104.56 2999 Operator Name APN Name Vodacom Vodameter Neotel internet Neotel Server Name Neotel UDP Server IP UDP Server Port 172.24.146.4 299 SAM Training

Equipment Communication Controller – Coms wiring Communication Cable Consumables ECS (Eth/E1), ECS-L 1. 10 way Ribbon Cable 2. 10 way IDC connector for 10 way ribbon cable 3. DB9 IDC, male and female for 10 way ribbon cable ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L 1. DB9, male and female, solder type 2. Milar cable used with point 1 above (Same as SAM2 Coms cross over cable) 1. RJ9 – small 4 way 2. RJ11 – large 4 way 3. RJ12 - 6 way 4. RJ45 – 8way 5. Cable for each above 6. CAT5 cable Possible Communication Cables needed 1. SAM1.5 2. SAM2, SAM3 & Access Control 3. Energy Meter (Landis & Gyrr) Rectifier 4. Rectifier (Battery Tech, Grintek, ASM, etc) 5. Generator (Lovato, Deep Sea, Intellilite, etc) 6. Fuel Cell (Idatech, Gencore, etc) SAM Training

ECS-L2 Communication wiring SAM2 & Access Control SAM Training

ECS-L2 Communication wiring SAM1.5 SAM Training

ECS-L2 Communication wiring landis & Gyrr SAM Training

ECS-L2 Communication wiring battery tech SM65 SAM Training

ECS-L2 Communication wiring battery tech SC200 Rear View SC200 RS232 Connection Front View SAM Training

ECS-L2 Communication wiring battery tech SM50 SAM Training

ECS-L2 Communication wiring Grintek gt500 SAM Training

ECS-L2 Communication wiring Deep Sea SAM Training

ECS-L2 Communication wiring Lovato SAM Training

Thank you