Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

Slides:

Advertisements

Similar presentations

How to check close-to-the-line arrows F E D E R A T I O N I T N E R N A T I O N A L E D E T I R A L ' A R C a b TOP VIEW FRONT VIEW a b c d e c d e.

Advertisements

Technical Sketching and Drawing

Technical Drawing CHAPTER 1

Engineering Drawing ELEC 106 Fundamentals of Electrical Engineering

Using Drawings to Communicate Lecture 2 –How to create front, top, & right side views of a part.

Laboratory 2: Introduction to AutoCAD and Microsoft Project

Orthographic Projection Basics

Exercise Exercise3.1 8 Exercise3.1 9 Exercise

Exercise Exercise Exercise Exercise

Fundamentals of Engineering – Honors – ENGR H191 Lecture 8 - Cadkey1 Question of the Day The Ohio State University will be your ‘Alma Mater’ – What is.

Exercise Exercise Exercise Exercise

The Other Side Product Design Sketching Activity.

Exercise Exercise6.1 7 Exercise6.1 8 Exercise6.1 9.

GEOMETRY Eqao preparation day 5.

Ch 17 communicating solutions 1.Alphabet of lines- technical lines used in multi-view drawings.

Geometry Perspectives

Isometric Drawing. The following presentation will demonstrate how to draw isometric objects using the “box method”. Use an isometric template sheet to.

Using Drawings to Communicate. EML 2023 Computer Aided Design communicate design intent How can you sketch this angle bracket to convey its shape effectively?

1-1 Nets and Drawings for Visualizing Geometry

Solids and Views A solid is in 3D. But we can only draw in 2D.... So how can we draw a solid?

Agenda More practice with isometric drawings

Technical Design Isometric and Orthographic Drawings.

Lesson 12-1 Pages Drawing Three- Dimensional Figures.

Drawings, Nets, and Other Models Drawings, Nets, and Other Models

Career & Technical Education Sketching 2.00 Explain and demonstrate basic sketching skills and techniques.

Laboratory 2: Introduction to DesignCAD97 and SureTrak Project Manager General Engineering Polytechnic University.

Warm-Up What 3-d geometric shape will the following nets fold to create? 1) 2) 3)

Agenda Learn to create an isometric sketch

CHAPTER 3 REVIEW What are the 7 steps of Engineering Design Process ? 1. Define the problem 2. Research the problem 3. Develop possible solutions 4. Choose.

EML 2023 – Modeling, Drawings Lecture Auxiliary and Section Views.

Auxiliary and Section Views. EML 2023 Computer Aided Design auxiliary views A surface that appears as inclined in a principal view can be shown in true.

 sketch - preliminary drawing for later elaboration; "he made several studies before starting to paint"  sketch - a brief literary description  make.

Views of Solids Geometry D. Sketching the views of the solid. First, use blocks to construct a similar solid to the one shown at the left.

What’s The Next Step to Beginning a Drawing……. You already Know: Measurements Tools.

Stem Agenda Week 8 10/15 – 10/19. Agenda 10/15  Careers Day with Ms. Benson!

Isometric Drawings & Orthographic Drawings Tutorial 5d.

Chapter 3 : Communicating Ideas. Audio communication – messages that can be heard.

Isometric Drawing Exercise. The following presentation will demonstrate how to draw isometric objects using the “box method”.

3D Pictorials. Isometric PictorialOblique Pictorial.

1.2 Drawings, Nets, and Other Models

Nets and Drawings for Visualizing Geometry

Representations of Three-Dimensional Figures

Technical Drawing.

Review and more practice

CAD Jim Cline July 20-21, 2017.

Sketching the Derivative

Sketching Practice Gateway To Technology®

Technical Drawing Visual Communication of Technical Information

Isometric Projection -the term ‘isometric’ comes from the Greek for ‘equal measure’ reflecting the scale along each axis is the same - Isometric views.

I can make Orthographic drawings

Introduction to Engineering Multi-view Drawings - 1

ENGN103 Engineering Drawing

Starter ‘What is the difference between 2D and 3D?

Orthographic Sketch Solution

ENGN103 Engineering Drawing

Scaled Drawings 7.07 Execute Scaled Drawings

Are the buildings below three dimensional shapes?

Isometric Drawing Exercise

Multiview Drawing Orthographic Projection

Inclined Planes & Curved Surfaces

3-D Views of Solid Figures

S1 Orthographic Sketching

ENGN103 Engineering Drawing

Orthographic Projection:

Engineering Graphics I

Introduction to Engineering Review: Isometric Drawings

Introduction to Engineering Review: Multi-view Drawings

1.2: Drawings, Nets, and other models

Engineering Design Graphics

Presentation transcript:

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

EML 2023 Computer Aided Design three view sketch 2

EML 2023 Computer Aided Design three view sketch 3

4

5

EML 2023 Computer Aided Design isometric drawings 6

EML 2023 Computer Aided Design exercise 7

EML 2023 Computer Aided Design exercise Make an isometric drawing. 8

EML 2023 Computer Aided Design exercise Make an isometric drawing. 9

EML 2023 Computer Aided Design exercise Make an isometric drawing. 10

EML 2023 Computer Aided Design exercise Make an isometric drawing. 11

12