 Introduction  Objectives  Mechanical & Electrical components  Control system  Future work  Conclusion.

Slides:

Advertisements

Similar presentations

Unit 7 Discrete Controllers

Advertisements

HYDRAULICS & PNEUMATICS

Dr. HABEEB HATTAB HABEEB Dr. HABEEB HATTAB HABEEB Office: BN-Block, Level-3, Room Ext. No.: 7292 UNITEN.

1 The University of Jordan Mechatronics Engineering Department PLC: Programmable Logical Controller.

SOLAR TRACKER PROJECT. INTRODUCTION: Solar tracker is a system that is used to track sun light to increase the efficiency of electricity gained from solar.

Introduction To Programmable Logic Controllers

FOLLOWER SENSORS AND ACTUATORS EE 552 INTSTRUCTOR :Dr MOHAN KRISNAN BY MOHAMMED KASHIF IQBAL ANESH BODDAPATTI UNIVERSITY OF DETROIT MERCY.

PLC Fundamentals Module 2: Hardware and Terminology.

GCSE Electronic Products

Timers - PAGE 1/20 - Timer Products. Timers - PAGE 2/20 - Multitechnology PROCESSING ACTUATING SENSING COMMUNICATING PROCESSING SOLUTIONS.

Module 2: Hardware and Terminology

PLC: Programmable Logical Controller

PROGRAMMABLE LOGIC CONTROLLER (PLC) AND AUTOMATION

Introduction to Robotics Principles of Robotics. What is a robot? The word robot comes from the Czech word for forced labor, or serf. It was introduced.

PLC introduction1 Discrete Event Control Concept Representation DEC controller design DEC controller implementation.

PLC: Programmable Logical Controller

Magnetic Contactor For handling large current and voltage.

SMART SOLAR TRACKING SYSTEM FOR OPTIMAL POWER GENERATION

MOTION CONTROL ISAT 303 Typically involves accurate control of distance, speed (angular velocity or both.

Use of a Programmable Logic Controller (PLC) for Automating the Vertical Movement of Weather Station Sensors Javier Chaparro 1 and Eric Harmsen 2, Dept.

Sensors are mostly electronic devices used to monitor or capture something.

PH4705 & ET4305: Digital Sensors

Introduction to Robo Pro

Module 1: Introduction to PLC

Question ONE What is the name of this component?.

Smart Plant Robot Prepared by Haya De’bas Jumanah Salhab Supervisor Dr. Ra’ed Al-Qadi.

Self Parking Lara Sabah Yaqeen Salatneh Dr.Ashraf Armoush

©2008 Pearson Education, Inc., Upper Saddle River, NJ. All rights reserved. This material is protected under all copyright laws as they currently exist.

Electrical Control Components

PROGRAMMABLE LOGIC CONTROLLER (PLC) AND AUTOMATION

Beath High School - Int 1 Physics1 Intermediate 1 Physics Electronics Glossary AND gate to device digital signals to inverter LDR to logic circuit logic.

Programmable Logic Controller (PLC)

Basic Electronics for Arduino -basic electronics -arduino related stuff -tips and tricks Rob Zimmermann 2015.

CAMLESS ELECTRONIC REGULATORY MODULE FOR A 4-S SINGLE CYLINDER I C ENGINE.

Copier Jam Detector Design Problem

18240 Element two - Components INPUTS OUTPUTS PURPOSE TYPICAL USE.

 Introduction.  Block Diagram.  Sensors.  Arduino.  Advantages.  Limitations.  Applications.  Conclusion. Contents.

Actuators and Control, Part 5 Grant Agreement No LLP UK-LEONARDO-LMP Project acronym: CLEM Project title: Cloud services for E-Learning.

BLDC Motor Speed Control with RPM Display. Introduction BLDC Motor Speed Control with RPM Display  The main objective of this.

Team work : Sherief Gameel el sayed Mohamed Ahmed abd elsalam Omar Medhat ezzat el kordy Presented to : Prof.Yehia Hendawy Eng.

AGROFARM WEATHER MONITOR USING LabVIEW. INTRODUCTION Innovation in agriculture field Implementing instrumentation tech. in agricultural field The quantity.

Stepper Motor – Types, Advantages And Applications

Characteristics of Instrumentation An instrument is a device that transforms a physical variable of interest (the measurand) into a form that is suitable.

WATER LEVEL INDICATOR AND AUTOMATIC MOTOR SWITCHING SYSTEM

Components of Mechatronic Systems AUE 425 Week 2 Kerem ALTUN October 3, 2016.

Lesson 1 PLC BASICS. PLC Definition  Programmable Logic Controllers are industrial computers that control machine and other applications.  PLC have.

Obstacle avoiding robot { pixel }

LG PLC COURSE Beginner Prepared by : -Hossam Mohammed -Ramdan said

Module 1: Introduction to PLC

SCADA for Remote Industrial Plant

Sensors For Robotics Robotics Academy All Rights Reserved.

Electronic Components

Arduino Development for Beginners

PLC: Programmable Logical Controller

fischertechnik® RoboPro Software for Gateway To Technology® RoboPro

Project Members: M.Premraj ( ) G.Rakesh ( ) J.Rameshwaran ( )

‘SONAR’ using Arduino & ultrasonic distance sensor

Outlines : Introduction . Construction . Control .

Objectives 1 – introduction 2 – mechanical design

PLC based automated coal crushing and conveyor system

IENG 475: Computer-Controlled Manufacturing Systems

Systems and Control.

ACOE347 – Data Acquisition and Automation Systems

IENG 475: Computer-Controlled Manufacturing Systems

Systems and Control.

Presentation transcript:

 Introduction  Objectives  Mechanical & Electrical components  Control system  Future work  Conclusion

 In our project the counter is used to count the hanged pieces on the conveyor.  If hanger or piece is absent,there is no count.

count the number of items passes a production line using two different methods get the reading from two different applications Increasing the accuracy of counting system..

sprocket gear

Solid bearing pin chain suitable for more arduous conveyor applications.

Limit Switch  the limit switch here is the first counter.  A count will be given when there is signal resulted from mechanically contact with a hanger and a hanged piece.

The total length of the chain = 264 cm The radius of the sprocket = 3.75 cm The total time for one revolution = 17.8 seconds. The linear velocity of the chain =V =L/T= 264/17.8=14.831cm/s The angular velocity of the motor =ω = V/R=14.831/3.75 = 3.9 rad/s....

DC Motor A DC motor is any of a class of electrical machines that converts direct current electrical power into mechanical power

LDRS SENSORS A Light Dependent Resistor (LDR) or a photo resistor is a device whose resistivity is a function of the incident electromagnetic radiationresistor

Laser pointer The laser pointer laser beam is used to control the resistance of the sensors.

CONTROLLING DEVICES

Connection of LDRs to UNO?

Connection of Limit Switches to UNO?

Why Aurduino UNO?  It is an open-source project, both in terms of hardware and software.  It is flexible, offers a variety of digital and analog inputs.  It is simple and easy to use.  It is more suitable for controlling models.

LCD Connection

 Programmable logical controller PLC will be used instead of the aurduino because its more suitable to control industries and production lines.  Ultra sonic sensor will be used instead of LDRs. It can Resist moisture, water, blood and dirt.

 use of double counters counting system could make it easy to discover whether there was a mistake in the count.  especially in large production lines because it can be difficult to count the hanged pieces manually.  if one of them is broken down the other will give a value.