Introduction Produced by Ron Markum, Team 1750 Ed Latimer, Team 476 Ken York, Team 476 2012.

Slides:



Advertisements
Similar presentations
CRIMPING Introduction
Advertisements

Build Your Own Future RC2 Serviceability. Build Your Own Future Safety and Ground Rules Before servicing, always remove A/C power from the unit and disconnect.
CORDLESS DRILL WHAT IS IT ? WHAT IS IT USED FOR ? click here
Drills & Drilling Drills & Drilling.
Robot Quick Build Session Transmission Assembly Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to.
Frame Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Presented by Team 3350 (T-BOTS).  Students should lead their teams in the building, design, and all other aspects of the robot.  Knowledge of the Kit.
Introduction To Frc electronics
C-Base Transmission Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Robot Quick Build Session Frame Assembly Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma.
Electrical Wiring Circuit Board Project. STEP 1 - Identify all Parts of the Project Saw Drill Driver w/ bits Drill w/bits (not pictured) #2 Phillips Screwdriver.
Tray Tools, Materials & Processes. The Pillar Drill can be used to drill wood, metal, and plastic. As a general rule the larger the hole you are trying.
Wiring the new control system MVRT 2010 – 2011 Season.
Applied Control Systems
FIRST Robotics Kit of Parts - KOP
How to Construct a Robot Part 7: Wiring and Controller Installation Copyright © Texas Education Agency, All rights reserved. 1.
Vex 1.0 © 2006 Carnegie Mellon Robotics Academy Inc. Test Bed Assembly.
FIRST Training Resource Pit Setup, Inspection and Judging Evan Morrison Mentor, Teams 190 and 971.
Robot Build IT Girls Allowed 2014 Updated 14 th August.
SANUS SYSTEMS THE UNION OF FORM AND FUNCTION Sanus Systems 2221 Hwy 36 West. St. Paul, MN
Technical Topics for Teams August BEST GAME RULES.
Wiring MVRT 2010 – 2011 Season. Table of Contents Wire stripping Crimping Soldering.
Electrical Workshop Session One 9/22/2014. FIRST Power Distribution Diagram.
Embedded Programming and Robotics Lesson 6 Mechanical Assembly 1.
Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.
Tray Tools, Materials & Processes. The Pillar Drill can be used to drill wood, metal, and plastic. As a general rule the larger the hole you are trying.
SpectraSonde Assembly. What is the SpectraSonde? Reads temperature, pressure, and humidity data from the atmosphere. The SpectraSonde doesn’t fly like.
1. A guide to wiring your robot. Jerry Skene Past mentor – Chantilly Robotics
Robot Quick Build Session RQBS Intro - Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma.
SeaPerch Design Challenge and Construction Overview.
Robot Quick Build Session Pre-Kickoff Preparations Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma.
Vex 1.0 © 2005 Carnegie Mellon Robotics Academy Inc. Electromechanical Relays.
Introduction to Robotics
SRA Lab Safety & Proposal PowerPoint Project This is a Partnered/Group Assignment Tech Ed - 9 Lab Safety & SRA Proposal Report Mr. Saunders Remember: This.
Control System and Electrical Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
AnaSonde-3M Assembly. What is the AnaSonde-3M? The AnaSonde-3M reads temperature, pressure and humidity data from the atmosphere. After the AnaSonde is.
Electronics and Robotics Merit Badges
Electricity By: Mr. Brock. Electrical Safety 1) Always disconnect the circuit to be worked on before anything else and lock the cover to the SEP when.
Hand Tools. 1. Adjustable Wrench Adjustable Wrench Turning various size nuts and bolts.
Building a Robot Exploring Computer Science Lesson 6-4.
Quick Build - Mechanical The University of Memphis.
P:\ISO \Work Instructions\Assembly\Options\ARMADILLO SWEEPER OPTIONS\10X ARMADILLO SWEEPER OPTIONS MODEL: KIT-MFG-ENG SHDN DSL M&FS SWA.
Build a Simple Electric Motor Uses a stator made of windings, an armature with two coils, and a commutator.
INTRODUCTION TO ROBOTICS Part 2: Structural System Robotics and Automation Copyright © Texas Education Agency, All rights reserved.
Connecting the cRIO to the 12 V power source and your computer
Tool Identification 1. Adjustable Wrench 2. Allen Wrench.
Do Now Heading: Electrical Safety Pick up 3 worksheets from the front table Open up your journals.
Robot Quick Build Session Programming Session Produced by Ken York, Team 476 Ed Latimer, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma State.
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
1 SPIRIT Silicon Prairie Initiative on Robotics in Information Technology Curriculum Overview.
Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.
MIND CONTROLLED ROBOT BY ADITHYA KUMAR EIGHTH GRADE.
Introduction Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Project Overview  Introduction  Clawbot Build  Design Modification  Design Development  Programming  Sensors  Advanced Sensors  Open design challenges.
 cRIO with all modules & connectors and cables for each module.  Digital sidecar with all connectors and cables.  Panel signal light indicator & connector.
Build A Motor You must follow the directions step-by-step!
Identifying and Maintaining Electrical Tools
PostBase Automatic Feeder Component Removal Service Training
Unit 1 - Introduction to VEX Robotics
25th Annual 7th and 8th Grade Battery Car Challenge
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Electrical Wiring Circuit Board Project
What’s in your kit?.
installing electrical system
Robotics Engineering Challenge 5
CAUTION GENERAL TOOLS REQUIRED ASSEMBLY AND INSTALLATION
Instructor Resources.
Pair work – Do you want to change seats??
Pair work – Do you want to change seats??
Presentation transcript:

Introduction Produced by Ron Markum, Team 1750 Ed Latimer, Team 476 Ken York, Team

Goal: A running kitbot in 4 hours! Note: The 2011 kitbot frame is shown below, not 2012.

Getting Started Break into 3 sub-teams: –Programming –Electronics –Transmission/Frame Get parts and go to rooms Expected time: 0:00-0:30 Introduction, pull parts from kit 0:30-3:00 Electronics team assembly & programming 0:30-2:30 Chassis (frame & transmission) assembly 3:00-4:00 Mount electronics board and test 4:00-5:00 Run robot or troubleshoot; clean-up NOTE: Getting the robot to run in wireless mode may be too challenging in a short amount of time. You may want to pick a deadline – say, 3:30 hours – to give up on wireless for the day and operate in tethered mode.

Rules 1. Wear safety glasses! Put them on now. 4. Start practicing ‘Gracious Professionalism’ today. 2. You are responsible for your own kit of parts. 3. Do not drill into any tables!

The Plan Get each team their parts and dismiss them in this order: 1.Programming team 2.Electronics team 3.Chassis team

Programming Team Pull the software CD from the Control Systems box and go to the programming room with your team’s laptop.

Parts to Pull from Plastic Bins Circuit Breaker Terminal lugs: Both crimp and screw-type lugs for the thick 6 AWG battery wire are in the kit Battery Charger Electronics Team Quick-disconnect Battery connectors Tie wraps, 4” and 8” Wire-6AWG Black Red

Control System Box No picture available Also take: 17”x37” electronics board 8”x24” driver station board ‘Goody’ bag of nuts/bolts/velcro/etc. 1 Battery Box (separate box – not in bins) Veteran Teams - Take reusable control system components from last year’s robot that you did not get in this year’s kit (cRio, etc.)

Wire strippers Wire cutters Wire crimpers Phillips screwdriver - #2 Flat Screwdriver Supplied Wago flat screwdriver 3/8” and 10mm combination wrenches Tape measure 1/4” and 3/8” Drills * Cordless drill * Return this to the Chassis Team after the holes are drilled in the electronics base plate. Tools for the Electronics Team Once the Electronics Team has all the parts and tools, go to the Electronics Room

Parts for Chassis Team 1.The Chassis ‘kit box’from AndyMark. That’s it! The two CIM drive motors are included in the kit this year. Note: There are two extra motors packed in the chassis kit this year. They are not used in the chassis construction, but keep them with the FIRST kit of parts for use in the coming weeks for other robot component systems you build.

1.The instructions for both the frame and the transmission are in one booklet in the AndyMark kit box. Online instructions are also available at 2.The AndyMark instructions cover both a 37”x27” ‘narrow’ robot and 27”x37” ‘wide’ robot. Most of the teams use the narrow style, but you can build the wide one if you prefer. 3.You will have to cut two of the frame pieces - see the instructions for details. For this we recommend a separate frame cutting area for with a power tool operated by an adult. Frame & Transmission Team