GE Interlogix Kalatel Division Product Update KTD-405 Programming & Standard Operations

KTD-405 Keypad Programming

KTD-405 keypad (Supervisor Programming) Boot-Up Screen KEYPAD ADDRESS: 99 KEYPAD 99

KTD-405 keypad (Supervisor Programming) Default display after applying power CAMERA --- MONITOR 1

KTD-405 keypad (Programming) Navigating the menus Key Function Displays the next menu Displays the previous menu Scrolls up when indicated by  in the menus Scrolls down when indicated by  in the menus Scrolls right when indicated by  in the menus Scrolls left when indicated by  in the menus Scrolls up, down, left or right when indicated by , , ,  in the menus Advances menus; exits menus if held for 3 seconds

KTD-405 keypad (Programming) Menus that were not available in the first releases of software are indicated by two beeps and the following display: NOT IMPLEMENTED

Supervisor Programming

KTD-405 keypad (Supervisor Programming) To Access Programming: Press and hold the key The unit will beep and show the following display Remote device programming must be accessed separately. Supervisor programming password is 1,4,7,6, Also includes All user programming ENTER PROGRAMMING CODE:

KTD-405 keypad (Supervisor Programming) Resetting the Factory Defaults The first menu to display will be this one. Press to advance to the next menu and to return to the previous menu at any time without changing any existing parameters RESET TO DEFAULTS? NO <+>=YES <->=NO NEXT

KTD-405 keypad (Supervisor Programming) If you pressed “+” (yes): The next display will show: Followed by: The keypad will advance to the next menu automatically 1=RESET ALL BUT TITLES 2=RESET ALL ARE YOU SURE? <+>=YES <->=NO NEXT INITIALIZING DEFAULTS PLEASE WAIT

KTD-405 keypad (Supervisor Programming) Setting The Keypad Address The address is a “user defined” two-digit number The address must be from 10 to 99 Each device on the RS-485 network must have a unique address Address 99 is automatically assigned when the keypad is first connected and will remain unless changed by the user Entering an address that is already used temporarily displays: Select  or  to skip over this menu KEYPAD ADDRESS: 99 (01-99) NEXT ADDRESS NOT AVAILABLE

KTD-405 keypad (Supervisor Programming) Backward Compatibility? If the KTD-405 is being used in a system with: Existing ProBridges Existing CBR-KB3 or CBR-KB3/J keypads Select YES to allow the KTD-405 to communicate properly with these devices. Select  or  to skip over this menu KB3 PTZ PROTOCOL? NO <+>=YES <->=NO NEXT

KTD-405 keypad (Supervisor Programming) Allow Remote Programming by user? If the KTD-405 is being used in a system with: Matrix Switchers or Multiplexers Alarm Monitoring Equipment Programmable Dome Cameras or Receivers Select YES to allow the user to enter the 9,5,1, password and program these devices Select  or  to skip over this menu ENABLE REMOTE PRGMG? YES <+>=YES <->=NO NEXT

KTD-405 keypad (Supervisor Programming) Programming Keypad Titles A keypad title can be up to 14 characters including: A – Z and 0 - 9 Keypads with titles can use the “Seize Control” option Supervisors can seize camera sites, multiplexers, VCRs, etc. Supervisors can seize an entire zone in the ZONE mode Use the joystick or these buttons to program the title Select  or  to skip over this menu KEYPAD TITLE: <> NEXT = , = , = , = ,

KTD-405 keypad (Supervisor Programming) Changing the SEIZE CONTROL code Use the number keys to enter the new code The keypad will advance to the next menu when the last digit is entered Select  or  to skip over this menu SEIZE CONTROL CODE: 8642 USE NUMBER KEYS NEXT

KTD-405 keypad (Supervisor Programming) Changing the SEIZE CONTROL time Use the number keys to enter the new time This is the number of minutes of inactivity before the keypad will exit the seize control mode Select  or  to skip over this menu SEIZE CONTROL TIME: 5 (1-10) MINUTES NEXT

KTD-405 keypad (Supervisor Programming) Restricting access to presets Use the number keys to enter the new limit This is the lowest preset number a user may change Select  or  to skip over this menu LOWEST USER PRGMD PRESET (01-64) 58 NEXT

KTD-405 keypad (Supervisor Programming) Programming the SOFT keys This feature is not yet implemented Select -,  or  to skip over this menu Pressing + displays the following message: PROGRAM SOFT KEYS? <+>=YES <->=NO NEXT NOT IMPLEMENTED

KTD-405 keypad (Supervisor Programming) Programming the ACCESS codes This feature is not yet implemented Select -,  or  to skip over this menu Pressing + displays the following message: CHANGE ACCESS CODES? <+>=YES <->=NO NEXT NOT IMPLEMENTED

User Programming

KTD-405 keypad (User Programming) To Access User Programming: Press and hold the key The unit will beep and show the following display User programming password is 5,7,9, ENTER PROGRAMMING CODE:

KTD-405 keypad (User Programming) Changing the Operating Mode Two choices are available: Digiplex Zone Use the joystick or these buttons to select the mode Select  or  to skip over this menu OPERATING MODE: DIGIPLEX <,>=SELECT NEXT = , = 

KTD-405 keypad (User Programming) DigiPlex mode Menus Setting the system size Enter the highest camera number in your system Select  or  to skip over this menu SYSTEM SIZE: <CAMERAS> 511 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Setting the system size Enter the highest monitor number in your system Select  or  to skip over this menu SYSTEM SIZE: <MONITORS> 64 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Setting the system size Enter the highest multiplexer number in your system Select  or  to skip over this menu SYSTEM SIZE: <MPLXS> 32 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Setting the system size Enter the highest VCR number in your system Select  or  to skip over this menu SYSTEM SIZE: <DSR/VCR> 32 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Setting the system size Enter the highest preset number in your system Select  or  to skip over this menu SYSTEM SIZE: <PRESETS> 63 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Restricting system access This menu restricts access to specified cameras Use the joystick or these buttons to select the camera Select  or  to skip over this menu CAMERA 000 ACCESS? YES <+>=YES <->=NO NEXT = , = 

KTD-405 keypad (User Programming) DigiPlex mode Menus Restricting system access This menu restricts access to specified cameras Use the joystick or these buttons to select the camera Select  or  to skip over this menu CAMERA 000 ACCESS? YES <+>=YES <->=NO NEXT = , = 

KTD-405 keypad (User Programming) DigiPlex mode Menus Restricting system access This menu restricts access to specified monitors Use the joystick or these buttons to select the monitor Select  or  to skip over this menu MONITOR 01 ACCESS? YES <+>=YES <->=NO NEXT = , = 

KTD-405 keypad (User Programming) DigiPlex mode Menus Restricting system access This menu restricts access to specified recorder Use the joystick or these buttons to select the recorder Select  or  to skip over this menu Pressing “+” displays this menu: Enter a number from 0 to 511, or 0 for NONE or DSR/VCR 01 ACCESS? YES <+>=YES <->=NO NEXT = , =  VCR 01 MATRIX INPUT: 000 <0=NONE> NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Restricting system access This menu restricts access to specified multiplexer Use the joystick or these buttons to select the multiplexer Select  or  to skip over this menu MPLX 01 ACCESS? YES <+>=YES <->=NO NEXT = , = 

KTD-405 keypad (User Programming) DigiPlex mode Menus If you pressed “+” (yes): The next display will show: Followed by: The keypad will advance to the next multiplexer menu automatically MPLX01 BRAND CBR DVMRe <,>=SELECT NEXT MPLX 01 MATRIX INPUT? 000 <0=NONE NEXT SELECT MAX OUTPUTS: 02 <,>=SELECT NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Programming the monitor offset Enter a number for the offset needed in your system Select  or  to skip over this menu MONITOR OFFSET NUMBER: 0 NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus Queuing and announcing call-ins If you select “+” in this display: You need to select either SINGLE or MULTIPLE tone here: Also specify a monitor to display the queued calls: Select  or  to skip over this menu ANNUNCIATION? NO <+>=YES <->=NO NEXT CALL TONE TYPE? MULTIPLE <,>=SELECT NEXT SPOT MONITOR NUMBER: 0 <0=UNASSIGNED> NEXT

KTD-405 keypad (User Programming) DigiPlex mode Menus End of menus notification Pressing  from the previous menu will cause the keypad to display this message: Select  or press and hold for 3 seconds to exit the menus PRESS <SEQ> FOR 3 SECONDS TO EXIT

KTD-405 keypad (User Programming) Changing the Operating Mode Two choices are available: DigiPlex Zone Use the joystick or these buttons to select the mode Select  or  to skip over this menu OPERATING MODE: ZONE <,>=SELECT NEXT = , = 

KTD-405 keypad (User Programming) Zone mode Menus Programming the Mode label This menu allows you to select one of several labels for the LCD display during normal operations Selections Include: ZONE, MPLX, DVMR, TERR, BLDG FLR, DEPT, STA, SITE, AREA Select  or  to skip over this menu LCD DISPLAY LABEL: ZONE <,>=SELECT NEXT

KTD-405 keypad (User Programming) Zone mode Menus Programming the zone titles This menu allows you to select a title to display when the specified zone is being accessed. Select  or  to skip over this menu Enter a two-digit code and the keypad will advance to the following menu automatically Program the label characters the same way as keypad titles ENTER ZONE ADDRESS: 01 (01-16) NEXT ZONE 01 TITLE: <> (01-16) NEXT

KTD-405 keypad (User Programming) Zone mode Menus Programming the Zone type This menu allows you to identify the specific device that makes up a zone: Selections Include: CALIBUR MMX, CBR DVMRe, CBR TRIPLEX, CBR DUPLEX, CBR SIMPLEX, MATRIX SWCH, Select  or  to skip over this menu ZONE 01 HUB: CBR DVMRe <,>=SELECT NEXT

KTD-405 keypad (User Programming) Zone mode Menus Setting the zone size (monitors) This menu restricts access only to available zone monitors Use the number buttons to set the number of monitors Select  or  to skip over this menu Setting the zone size (cameras) This menu restricts access only to available zone cameras Choices include 4, 9, 10, 16 and 32 Use the joystick or these buttons to select the mode ZONE 01 MON. OUTPUTS? 01 TO 02 NEXT ZONE 01 CAM. INPUTS? 16 <,>=SELECT NEXT = , = 

KTD-405 keypad (User Programming) Zone mode Menus Programming zone access privileges Program the cameras that this keypad can access: Program the monitors that this keypad can access: Program user access to the zone’s recorder : You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros. ZONE 1 CAM 01 ACC? YES <+>=YES <->=NO NEXT ZONE 1 MON 01 ACC? YES <+>=YES <->=NO NEXT ZONE 1 RECORDER ACC? YES <+>=YES <->=NO NEXT

KTD-405 keypad (User Programming) Zone mode Menus If the Zone type is set to MATRIX SWCH: The zone size and access menus displays are slightly different ZONE 02 HUB: MATRIX SWCH <,>=SELECT NEXT

KTD-405 keypad (User Programming) Zone mode Menus Programming zone size Program the first camera input number for this zone: Program the number of monitors for this zone: Program the number of camera inputs on this zone: Choices include 4, 9, 10, 16 and 32 SELECT START INPUT: 032 <,>=SELECT NEXT ZONE 02 MON. OUTPUTS: 01 TO 16 NEXT ZONE 02 CAM. INPUTS: 64 <,>=SELECT NEXT

KTD-405 keypad (User Programming) Zone mode Menus Programming zone access privileges Program the cameras that this keypad can access: Program the monitors that this keypad can access: Program user access to the zone’s recorder : You should deny access unless you have a Triplex or MMX connected to a VCR using sub-macros. ZONE 02 CAM 01 ACC? YES <+>=YES <->=NO NEXT ZONE 02 MON 01 ACC? YES <+>=YES <->=NO NEXT ZONE 02 RECORD ACC? YES <+>=YES <->=NO NEXT

KTD-405 keypad (User Programming) Zone mode Menus Queuing and announcing call-ins If you select “+” in this display: You need to select either SINGLE or MULTIPLE tone here: Also specify a monitor to display the queued calls: Select  or  to skip over this menu ANNUNCIATION? NO <+>=YES <->=NO NEXT CALL TONE TYPE? MULTIPLE <,>=SELECT NEXT SPOT MONITOR NUMBER: 0 <0=UNASSIGNED> NEXT

KTD-405 keypad (User Programming) Zone mode Menus End of menus notification Pressing  from the previous menu will cause the keypad to display this message: Select  or press and hold for 3 seconds to exit the menus PRESS <SEQ> FOR 3 SECONDS TO EXIT

Remote Programming

KTD-405 keypad (Remote Programming) To Access Remote Programming: Press and hold the key The unit will beep and show the following display User programming password is 9,5,1, Correct password entry will cause the following display: Each selection generates a different set of menus ENTER PROGRAMMING CODE: 1=SWITCHER/MPLX 2=ALARMS 3=CAMERA/RCVR EXIT

KTD-405 keypad (User Programming) Switcher/Mux Menus Switcher/Multiplexer Programming Identify the device to be programmed If you select “1” (440) enter the monitor number to use for programming the switcher The keypad will display this message 1=440 2=CALIBUR 3=340/348 BACK ENTER MONITOR NUMBER: (1-64) BACK SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

KTD-405 keypad (User Programming) Switcher/Mux Menus Identify the device to be programmed If you select “2” (CALIBUR) enter the RS-485 address of the unit to be programmed The keypad will display this message 1=440 2=CALIBUR 3=340/348 BACK ENTER CALIBUR ADDRESS: (1-32) BACK SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

KTD-405 keypad (User Programming) Switcher/Mux Menus Identify the device to be programmed If you select “3” (340/348) enter the monitor number to use for programming the switcher The keypad will display this message 1=440 2=CALIBUR 3=340/348 BACK ENTER MONITOR NUMBER: (1-64) BACK SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

KTD-405 keypad (User Programming) Alarm Menu Alarm Programming The keypad will display this message SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

Camera/Receiver Menus KTD-405 keypad (User Programming) Camera/Receiver Menus Camera/Receiver Programming (DigiPlex) Identify the device to be programmed If you select “1” (CYBERDOME) enter the camera address to be programmed The keypad will display this message 1=CYBERDOME 2=PTZ 3=AUXILIARY BACK ENTER CYBERDOME SITE NUMBER BACK SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

Camera/Receiver Menus KTD-405 keypad (User Programming) Camera/Receiver Menus Camera/Receiver Programming (Zone) Identify the device to be programmed, AND Make sure you have selected the Zone before you enter programming If you select “1” (CYBERDOME) enter the camera address to be programmed (address must be within the zone) The keypad will display this message 1=CYBERDOME 2=PTZ 3=AUXILIARY BACK ENTER ZONE 1 CAMERA NUMBER__ BACK SEE MONITOR FOR MENUS HOLD SEQ <3 SEC> TO EXIT

KTD-405 keypad (User Programming) PTZ/Auxiliary Menus PTZ OR Auxiliary Programming If you select “2” or “3” from this menu The keypad will display this message 1=CYBERDOME 2=PTZ 3=AUXILIARY BACK NOT IMPLEMENTED

Standard Operation

KTD-405 keypad (Standard Operation) Default display after applying power DigiPlex mode Zone Mode CAMERA --- MONITOR 1 ZONE – ZONE TITLE CAMERA -- MONITOR -

KTD-405 keypad (Standard Operation) Accessing System Information: Press and hold the key to display the system information The keypad will display Use  or  to move between these additional system information displays KEYPAD ADDRESS: 99 KEYPAD 99 NEXT VERSION 0.1.07 Dec 20 2001 09:32:44 CAM MN MX RC PS QS MO AT 511 64 32 32 63 58 00 W

KTD-405 keypad (Standard Operation) Accessing Help displays: Press + to display the Help menu In the help menus: Pressing any key displays that key’s function + “key” displays that key’s shifted function The help display will cease display after 10 seconds of inactivity

KTD-405 keypad (Standard Operation) Selecting a monitor: There are two ways: Enter the monitor number with any preceding zeroes Example: 1 (systems with less than 10 cameras) Example: 01 (systems with more than 9 cameras) Enter the monitor number, then press Example: 1 + CAMERA --- MONITOR 1

KTD-405 keypad (Standard Operation) Selecting a camera: There are two ways: Enter the camera number with any preceding zeroes Example: 3 (systems with less than 10 cameras) Example: 03 (systems with less than 100 cameras) Example: 003 (systems with more than 99 cameras) Enter the camera number, then press Example: 3 + CAMERA --- MONITOR 1

KTD-405 keypad (Standard Operation) Controlling a camera: Select the camera to be controlled Pan, Tilt and Zoom can be controlled by the joystick  Up/Down for Tilt control  Left/Right for Pan control  Twist the joystick for Zoom or use the key Use the and keys for these functions CAMERA 003 MONITOR 1

KTD-405 keypad (Standard Operation) Setting a preset: Position the camera Press the Store key Enter the preset number in one of three ways: Enter the two-digit number (Ex. 05 or 16) Use the AUX-1, AUX-2, AUX-3 or AUX-4 keys for 58-61 Use and for presets 62 and 63 (left and right Auto-Pan limits. Presets 62 and 63 can not be set by entering the two-digit numbers. On with these two keys and .

KTD-405 keypad (Standard Operation) Programming a Groups (salvos) and Tours: Requires a RS-485 connection and zone selected Requires Switcher monitor groups to be previously programmed Press Store + Sequence This menu will display: Enter a number from 1 to 64 calls that group of cameras on the monitors If you press the Tour key the following menu is displayed: Enter a number from 1 to 12 TO START that group sequence on the monitors DigiPlex Mode ENTER MONITOR GROUP (1-64)-- OR <TOUR> ENTER GROUP SEQUENCE (1-12)--

KTD-405 keypad (Standard Operation) Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232) Digiplex Mode Key Function DSR/VCR Function DVMRe  Starts recording  Stops record or playback Starts playback Pauses playback Pauses playback or live mode Fast Forward Fast Reverse (rewind) Frame advance Depends on device (DSR/VCR) Play forward (from reverse play) Frame advance (in pause mode) Frame reverse Play reverse (from forward play) Frame reverse (in pause mode n/a 2X digital zoom toggle Activates play and displays search menu

KTD-405 keypad (Standard Operation) Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232) Digiplex Mode Key Function DSR/VCR Function DVMRe Joystick functions ↻ Twist right = variable rate forward ↺ Twist left = variable rate reverse In Play or Pause modes:  Skip forward 2MB (about 15 sec.)  Skip backward 2MB (about 15 sec.)  Fast Forward  Fast Reverse (rewind)  Return to center position resumes pause mode In 2X Zoom mode:  Tilt up  Tile down  Pan right  Pan left

KTD-405 keypad (Standard Operation) Controlling a multiplexer: Requires RS-485 connection Zone Mode Key Function Multiplexer Function VCR/DSR   Starts recording  Stops record or playback Starts playback Pauses playback Pauses playback or live mode Fast Forward Fast Reverse (rewind) Frame advance Frame advance (in pause mode) Frame reverse Frame reverse (in pause mode 2X digital zoom toggle n/a Activates play and displays search menu  Multiplexer must support sub-macro VCR interface

KTD-405 keypad (Standard Operation) Controlling a multiplexer: Requires a RS-485 connection Zone Mode Key Function Multiplexer Function DSR/VCR  Joystick functions n/a In Play or Pause modes: ↻ Twist right = variable rate forward ↺ Twist left = variable rate reverse In 2X Zoom mode:  Tilt up  Tile down  Pan right  Pan left  Multiplexer must support sub-macro VCR interface

KTD-405 keypad (Standard Operation) Programming a multiplexer AutoList sequence: Requires a RS-485 connection and zone selected Press Store Press Sequence This menu will display: Enter the first camera number in the sequence Wait the desire amount of time you want this camera displayed Enter the next camera number in the sequence Repeat procedure until all cameras have been entered in the sequence Press  to cancel or  to exit and save the sequence and exit Zone Mode ENTER SEQUENCE CAMERA CANCEL DONE

KTD-405 keypad (Standard Operation) Controlling a recording device: Requires a KTD-93 interface (RS-422 to RS-232) Zone Mode Key Function DSR/VCR  Starts recording  Stops record or playback Starts playback Pauses playback Fast Forward Fast Reverse (rewind) Frame advance Depends on device (DSR/VCR) Frame reverse Joystick ↻ Twist right = variable rate forward ↺ Twist left = variable rate reverse

KTD-405 keypad (Standard Operation) Programming a Calibur™ multiplexer: Requires RS-485 connection Enter programming via the Remote Programming code 9,5,1, Select 1 for switcher/multiplexer Select 2 for Calibur Enter the Calibur RS-485 address Press (ENTER) Enter the Calibur password for the device Zone Mode

KTD-405 keypad (Standard Operation) Programming a Calibur™ multiplexer: Navigate the Calibur multiplexer menus with these keys: Zone Mode Key Function  Joystick moves left, right, up, down in menus Makes selections Backspaces out of selections or exits programming from the main menu  Move up in menus  Move down in menus  Move right in menus  Move left in menus Same as

KTD-405 keypad (Standard Operation) Keys with special functions: These keys have some special applications: Key Function Programmable two ways: Use with number keys to display mult-image views (if supported) Used to sequence through multi-display image views (if supported) OPEN or Preset 58 CLOSE or Preset 59 STOP or Preset 60 TALK or Preset 61 Used for activating tours or Auto-Pan mode Used to send the selected camera to a preset (if camera is capable) Clears numerical menu entries (future function clears alarms) Places selected CyberDome in auto-focus Addresses remote recording device

KTD-405 keypad (Standard Operation) Keys with special functions: These keys have not been implemented yet: Key Function Alarm key 1st (First) key

? PYTANIA