CMOS Fabrication nMOS pMOS.

Slides:

Advertisements

Similar presentations

Digital Integrated Circuits© Prentice Hall 1995 Design Rules Jan M. Rabaey Design Rules.

Advertisements

CMOS Fabrication EMT 251.

Lecture 0: Introduction

Simplified Example of a LOCOS Fabrication Process

EE141 © Digital Integrated Circuits 2nd Manufacturing 1 Digital Integrated Circuits A Design Perspective Manufacturing Process July 30, 2002.

CMOS Process at a Glance

Analog VLSI Design Nguyen Cao Qui.

VLSI Design Lecture 2: Basic Fabrication Steps and Layout

EE141 © Digital Integrated Circuits 2nd Manufacturing 1 CMOS Process Manufacturing Process.

CSCE 612: VLSI System Design Instructor: Jason D. Bakos.

Introduction to CMOS VLSI Design Lecture 0: Introduction

Modern VLSI Design 2e: Chapter 2 Copyright  1998 Prentice Hall PTR Topics n Basic fabrication steps n Transistor structures n Basic transistor behavior.

Elettronica D. AA Digital Integrated Circuits© Prentice Hall 1995 Manufacturing Process CMOS Manufacturing Process.

Lecture #51 Lecture #5 – VLSI Design Review zPhotolithography zPatterning Silicon zProcess steps used are: yStarts with Si wafer yThermal oxidation yPhotoresist.

CSCE 613: Fundamentals of VLSI Chip Design Instructor: Jason D. Bakos.

Design and Implementation of VLSI Systems (EN1600) lecture05 Sherief Reda Division of Engineering, Brown University Spring 2008 [sources: Weste/Addison.

CSE477 L05 IC Manufacturing.1Irwin&Vijay, PSU, 2002 CSE477 VLSI Digital Circuits Fall 2002 Lecture 05: IC Manufacturing Mary Jane Irwin (

Device Fabrication Example

Introduction Integrated circuits: many transistors on one chip.

CMOS Process Integration ECE/ChE 4752: Microelectronics Processing Laboratory Gary S. May March 25, 2004.

Z. Feng VLSI Design 1.1 VLSI Design MOSFET Zhuo Feng.

CMOS Fabrication Details

Module-3 (MOS designs,Stick Diagrams,Designrules)

２． Transistors and Layout Fabrication techniques Transistors and wires Design rule for layout Basic concepts and tools for Layout.

VLSI Design Lecture 2: Basic Fabrication Steps and Layout Mohammad Arjomand CE Department Sharif Univ. of Tech. Adapted with modifications from Harris’s.

VLSI, Lecture 1 A review of microelectronics and an introduction to MOS technology Department of Computer Engineering, Prince of Songkla.

Modern VLSI Design 4e: Chapter 2 Copyright  2009 Prentice Hall PTR Topics n Basic fabrication steps. n Transistor structures. n Basic transistor behavior.

Lecture 0: Introduction. CMOS VLSI Design 4th Ed. 0: Introduction2 Introduction  Integrated circuits: many transistors on one chip.  Very Large Scale.

EE141 © Digital Integrated Circuits 2nd Manufacturing 1 Chapter 2 Manufacturing Process March 7, 2003.

Modern VLSI Design 3e: Chapter 2 Copyright  1998, 2002 Prentice Hall PTR Topics n Design rules and fabrication. n SCMOS scalable design rules. n Stick.

Penn ESE370 Fall Townley & DeHon ESE370: Circuit-Level Modeling, Design, and Optimization for Digital Systems Day 14: October 1, 2014 Layout and.

ECE484: Digital VLSI Design Fall 2010 Lecture: IC Manufacturing

Modern VLSI Design 3e: Chapter 2 Partly from 2002 Prentice Hall PTR week2-1 Lecture 4 Transistor as Switch Jan

Penn ESE370 Fall Townley & DeHon ESE370: Circuit-Level Modeling, Design, and Optimization for Digital Systems Day 13: October 5, 2011 Layout and.

Introduction to CMOS VLSI Design CMOS Fabrication and Layout Harris, 2004 Updated by Li Chen, 2010.

Lecture 24a, Slide 1EECS40, Fall 2004Prof. White Lecture #24a OUTLINE Device isolation methods Electrical contacts to Si Mask layout conventions Process.

Introduction EE1411 Design Rules. EE1412 3D Perspective Polysilicon Aluminum.

STICK DIAGRAM EMT251. Schematic vs Layout In Out V DD GND Inverter circuit.

EE141 © Digital Integrated Circuits 2nd Manufacturing 1 Digital Integrated Circuits A Design Perspective Manufacturing Process Jan M. Rabaey Anantha Chandrakasan.

IC Fabrication/Process

NMOS FABRICATION 1. Processing is carried out on a thin wafer cut from a single crystal of silicon of high purity into which the required p-impurities.

CORPORATE INSTITUTE OF SCIENCE & TECHNOLOGY, BHOPAL DEPARTMENT OF ELECTRONICS & COMMUNICATIONS NMOS FABRICATION PROCESS - PROF. RAKESH K. JHA.

Purpose of design rules:

Modern VLSI Design 2e: Chapter 2 Copyright  1998 Prentice Hall PTR Topics n Basic fabrication steps n Transistor structures n Basic transistor behavior.

1 Overview of Fabrication Processes of MOSFETs and Layout Design Rules.

Dynamic Behavior of MOS Transistor. The Gate Capacitance t ox n + n + Cross section L Gate oxide x d x d L d Polysilicon gate Top view Gate-bulk overlap.

CMOS VLSI Design Introduction

CMOS VLSI Fabrication.

Silicon Design Page 1 The Creation of a New Computer Chip.

STICK DIAGRAM EMT251. Schematic vs Layout In Out V DD GND Inverter circuit.

CMOS FABRICATION.

Layout design rules. 2 Introduction  Layout rules is also referred as design rules.  It is considered as a prescription for preparing photomasks. 

EE141 Manufacturing 1 Chapter 2 Manufacturing Process and CMOS Circuit Layout 1 st rev. : March 7, nd rev. : April 10, 2003.

2007/11/20 Paul C.-P. Chao Optoelectronic System and Control Lab., EE, NCTU P1 Copyright 2015 by Paul Chao, NCTU VLSI Lecture 0: Introduction Paul C.–P.

UNIT II CIRCUIT DESIGN PROCESSES

EE141 © Digital Integrated Circuits 2nd Manufacturing 1 Manufacturing Process Dr. Shiyan Hu Office: EERC 731 Adapted and modified from Digital Integrated.

Out Line of Discussion on VLSI Design Basics

Patterning - Photolithography

CMOS Fabrication EMT 251.

CMOS VLSI Design Lecture 2: Fabrication & Layout

1. Introduction. Diseño de Circuitos Digitales para Comunicaciones Introduction Integrated circuits: many transistors on one chip. Very Large Scale Integration.

IC Manufactured Done by: Engineer Ahmad Haitham.

Topics Design rules and fabrication SCMOS scalable design rules

Subject Name: Fundamentals Of CMOS VLSI Subject Code: 10EC56

Chapter 1 & Chapter 3.

Design Rule EMT 251.

Introduction to Layout Inverter Layout Example Layout Design Rules

VLSI Design CMOS Layout

Presentation transcript:

CMOS Fabrication nMOS pMOS

The Fabrication Process The fabrication process consists of a series of steps in which layers of the chip are defined through the photolithography process. Inverter can be described as having six masks namely: n-well Polysilicon n+ diffusion p+ diffusion Contacts and metal The first processing step is that of oxidation (allows for protection of regions that need not be doped). Form an n-well using a Group V element (this changes substrate from p-type to n-type to accommodate the pMOS). Region devoid of the SiO2 get doped. Dopants can be introduced into the wafer by diffusion or ion implantation.

Layout Design Rules Layout design rules describe device dimensions and how close different and like layers can be brought to close proximity without creating shorts. The lambda based design rules made popular by Mead and Conway are based on the single parameter l and permit for ease of scaling. Industry used micron as a unit of measure and this makes scaling difficult since not all dimensions do not scale uniformly. Lambda (l) is generally half of the minimum drawn transistor channel length. The channel length describes the distance between the inside edges of the source and drain. It is set by the minimum poly width. We are begin to refer to the gate channel length in nanometers (nm) whereas for technologies 0.18 mm and above we used the micron.

Layout Design Rules Lambda rules allow for ease of migrating designs from one technology node to another. Our Cad Tools in the Lab measure in micron. Academia relies on MOSIS (fabrication house (foundry)) to fabricate their designs. MOSIS provides a comprehensive summary of scalable CMOS (SCMOS) rules at http://www.mosis.org These rules cover a wide range of manufacturing processes. The rules define minimum wire widths to avoid breaks, minimum spacing to avoid shorts between neighboring wires and minimum overlap to minimize parasitic capacitance. Contacts have traditionally been kept at 2l X 2l for different technology generations. Polysilicon has a minimum width of 2l and must overlap diffusion by 2l and must be 1l away from the next poly wire.

Gate Layout VDD To lesson the possibility of having layers of the same material creating short circuits, it is best to have same layers oriented in the same direction (metal1 placed horizontally while poly runs vertically). GND