1. © Erosion And Penetration Rates Of A Pipe Protruded In A Sudden Contraction Habib, MA; Ben-Mansour, R; Badr, HM; Kabir, ME PERGAMON-ELSEVIER SCIENCE LTD, COMPUTERS FLUIDS; pp: ; Vol: 37 King Fahd University of Petroleum & Minerals Summary Numerical investigation of erosion of a pipe protruded in a sudden contraction is presented. The presence of sand in the produced fluid provides many challenges for oil and gas producing companies. Moreover, sand presence causes loss of pipe wall thickness that can lead to pipe erosion, frequent failures and loss of valuable production time. In order to reduce the frequency of such pipe erosions, caps in the form of replaceable pipes are protruded in the sudden contraction regions which are exposed to most of the serious erosion rates. The importance of this problem is mainly due to many related engineering applications, viz. heat exchangers. In the present work, numerical investigation of the erosion of a pipe protruded in a sudden contraction is presented. The geometry is axi-symmetric abrupt contraction pipe with a pipe protrusion embedded in it. The flow is steady, 2D axi-symmetric and is considered turbulent. The Lagrangian approach including flow modeling, particle tracking and erosion calculation was utilized. The continuous flow field was solved by steady-state time averaged conservation equations of mass and momentum along with RNG-model for turbulence. Particles are tracked by using Lagrangian particle tracking. Finally, an erosion model was employed to investigate the erosion phenomena for the given geometry. The influence of the different parameters such as the inlet flow velocity, the particle diameter, the protruded pipe geometry, the pipe wall material and the pipe contraction ratio on the erosion and penetration of pipe protrusion was investigated. (c) 2007 Elsevier Ltd. All rights reserved. References: AHLERT KR, 1994, THESIS U TULSA Copyright: King Fahd University of Petroleum & Minerals;

© ASTARITA G, 1968, IND ENG CHEM FUND, V7, P27 BADR HM, 2002, 6 SAUD ENG C DHAHR K, V5 BADR HM, 2005, COMPUT FLUIDS, V34, P721, DOI /j.compfluid BENEDICT RP, 1966, T ASME A, V88, P73 BULLEN PR, 1996, P I MECH ENG, V210, P171 CLIFT R, 1978, BUBBLES DROPS PARTIC DURST F, 1984, APPL MATH MODEL, V8, P101 EDWARDS JK, 1998, ASME FLUIDS ENG DIV EDWARDS JK, 2000, P ASME FLUIDS ENG DI FOSSA M, 1998, INT J HEAT MASS TRAN, V41, P3807 HABIB MA, 2004, INT J NUMER METH FL, V46, P19, DOI /fld.744 JAYANTI S, 1991, 0099 AEA APS HARW LA KAYS WM, 1950, T ASME, V72, P1067 KHEZZAR L, 1986, P I MECH ENG C-J MEC, V200, P447 LU QQ, 1993, INT J MULTIPHAS FLOW, V19, P347 MCLAURY B, 1996, THESIS U TULSA MENG H, 1991, ASME FLUIDS ENG DIVI, V118, P183 MICHAELIDES EE, 1997, J FLUID ENG-T ASME, V119, P233 MORSI SA, 1972, J FLUID MECH, V55, P193 NEILSON JH, 1968, WEAR, V11, P111 ODAR F, 1964, J FLUID MECHANICS 2, V18, P302 PATANKAR SV, 1980, NUMERICAL HEAT TRANS PICART A, 1986, INT J MULTIPHAS FLOW, V12, P237 POSTLETHWAITE J, 1993, CORROSION, V49, P850 SAFFMAN PG, 1965, J FLUID MECH, V22, P385 SALAMA MM, 1983, OFFSH TECHN C TX MAY SHIH TH, 1995, COMPUT FLUIDS, V24, P227 SHIRAZI SA, 1995, J PRESS VESS-T ASME, V117, P45 TU JY, 1996, ASME FED, V236, P751 VERSTEEG HK, 1995, INTRO COMPUTATIONAL WALLACE MS, 2000, P 2000 ASME FLUIDS E WALLACE MS, 2004, WEAR, V256, P927 WILCOX DC, 2000, TURBULENCE MODELING WOOD RJK, 2004, WEAR, V256, P937 For pre-prints please write to: Copyright: King Fahd University of Petroleum & Minerals;