Telephone Network & Signaling System

8.2 Telephone Network Major Components LATAs Making a Connection Analog Services Digital Services A Brief History

Figure 8.11 A telephone system

Intra-LATA services are provided by local exchange carriers. Since 1996, there are two types of LECs: incumbent local exchange carriers and competitive local exchange carriers. Note:

Figure 8.12 Switching offices in a LATA

Figure 8.13 POPs

Figure 8.14 Rotary and touch-tone dialing

Voice communication used analog signals in the past, but is now moving to digital signals. On the other hand, dialing started with digital signals (rotary) and is now moving to analog signals (touch-tone). Note:

T1 Channel Bank TDM Analog Voice Lines Channel Bank for 24 Analog Lines with Analog to Digital Conversion F Each analog voice line (Channel) is sampled 8,000/s (resolution is 8 bits) 24 Digital Channels with Framing bit F. DS0 = 8,000x8=64 kb/s DS1 = 24 DS0 + 8 kb/s DS1 = 1,536+8 = kb/s TDM … Time Division Multiplexing 125 micro sec. Local Loop

Digital Switching T1 or DS-1 Transmission Frame (US) Bit 193 (F) is framing bit, used for synchronization Voice channels: 7-bit PCM, bit 8 is a signaling bit Data channels: bit 8 of Ch 24 is used for control (8 kb/s) reducing capacity to 56 kb/s F Channel 1Channel 2Channel micro seconds 193 bits

Digital Hierarchy (US, EU) CarrierChannelsData Rate DS Mb/s DS-1T Mb/s DS-2T Mb/s DS-3T Mb/s E Mb/s E Mb/s E Mb/s

Optical Hierarchy OpticalElectricalRate OC-1STS-151 Mb/s OC-33 x STS-13 x 51 Mb/s OC-3cSTS-3155 Mb/s OC-12STS Mb/s OC-24STS Gb/s OC-48STS Gb/s OC-192STS Gb/s Note: OC and STS circuits are usually used with SONET (Synchronous Optical NETwork )

Signaling Signaling is a technical term used by the telephone industry. Signaling is a set of protocols and associated data exchange for managing the telephone network: –A signal to indicate Off- and On-Hook condition of the telephone set –Transmission of dial tones, busy tones, ringing signal, Caller ID service, etc. –Transmission of inter-exchange data for rerouting calls, diagnostics information, etc. –Transmission business information for billing and accounting.

Control Signaling Functions Audible communication with subscriber Transmission of dialed number Call can not be completed indication Call ended indication Signal to ring phone Billing info Equipment and trunk status info Diagnostic info Control of specialist equipment

Control Signal Sequence Both phones on hook Subscriber lifts receiver (off hook) End office switch signaled Switch responds with dial tone Caller dials number If target not busy, send ringer signal to target subscriber Feedback to caller –Ringing tone, engaged tone, unobtainable Target accepts call by lifting receiver Switch terminates ringing signal and ringing tone Switch establishes connection Connection release when Source subscriber hangs up

Switch to Switch Signaling Subscribers connected to different switches Originating switch seizes interswitch trunk Send off hook signal on trunk, requesting digit register at target switch (for address) Terminating switch sends off hook followed by on hook (wink) to show register ready Originating switch sends address

Location of Signaling Subscriber to network –Depends on subscriber device and switch Within network –Management of subscriber calls and network –More complex

Inband Signaling Inband (or inchannel) signaling transmits control signals in the same channel used by the customer voice (or data) signals Simple but exposed to fraud Office A Office B Sig

Inband Signaling Call Set Up 20 seconds set-up time Less efficient trunk occupancy More vulnerable to fraud on the network Call Processing Overhead Fixed Routing Patterns

Out-of-Band Signaling Transmits control signals using the same facilities as the voice but a different part of the frequency band Provides for continuous supervision (less fraud) Office A Office B Sig

Out-of-Band Signaling Call Set Up 1-3 seconds set-up time Maximize trunk utilization Highly secure Minimal switch overhead Flexible design

Common Channel Signaling Transmits control signals over dedicated signaling links that are common to a number of voice channels. Signaling System 7 (SS7) is a standard that provides internal control and network intelligence for circuit switched networks. SS7 Office A Office B SP Trunks for Voice Signal Point SP STP Signal Transfer Points

Signaling System 7 Specified in 1980, updated in 1984 and 1988 Supports circuit switching and packet switching (e.g., X.25 and Frame Relay) A very complex piece of software that manages all the switches in the telephone network (over 10 million lines of code) Installed in the Signal Point (SP) computer network to control the Signal Transfer Point (STP) switches which carry all voice and data traffic

Signaling System 7 l Enhanced services requested by users require bidirectional signaling capabilities, flexibility of call setup and remote database access l With SS7, a signaling channel conveys, by means of labeled messages, signaling information relating to call processing and to network management l SS7 is the most important signaling system in the world: it supervises the PSTN, the cellular networks (GSM), and the Intelligent Network

SS7 in the PSTN Circuit Switching Network Switch NNI CPE CPE: Customer Premises Equipment UNI: User-Network Interface NNI: Network-Network Interface ISDN: Integrated Services Digital Network UNI AnalogSS7 ISDNSS7 Analog ISDN

Interface between the circuit switching network and the signaling network Voice Circuits Signaling Links Control Unit Signaling Network (SS7) Signaling Point Signaling Point Control Unit

Signaling and Switching Planes Switching Plane Signaling Plane Signaling link Voice circuits SP STP SP SP: Signaling Point STP: Signaling Transfer Point

Example of Signaling Network Network 1 Network 2 STP SP... SP STP

SP STP

1.Switch A analyzes the dialed digits and determines that it needs to send the call to switch B. 2. Switch A selects an idle trunk between itself and switch B and formulates an initial address message (IAM), the basic message necessary to initiate a call. The IAM is addressed to switch B. It identifies the initiating switch (switch A), the destination switch (switch B), the trunk selected, the calling and called numbers, as well as other information. 3. Switch A picks one of its a link (e.g., AW) and transmits the message over the link for routing to switch B.

4. STP W receives a message, inspects its routing label, and determines that it is to be routed to switch B. It transmits the message on link BW. 5. Switch B receives the message. On analyzing the message, it determines that it serves the called number and that the called number is idle. 6. Switch B formulates an address complete message (ACM), which indicates that the IAM has reached its proper destination. The message identifies the recipient switch (A), the sending switch (B), and the selected trunk.

7. Switch B picks one of the links (e.g., BX) and transmits the ACM over the link for routing to switch A. At the same time, it completes the call path in the backwards direction (towards switch A), sends a ringing tone over that trunk towards switch A, and rings the line of the called subscriber. 8. STP X receives the message, inspects its routing label, and determines that it is to be routed to switch A. It transmits the message on link AX. 9. On receiving the ACM, switch A connects the calling subscriber line to the selected trunk in the backwards direction (so that the caller can hear the ringing sent by switch B). 10. When the called subscriber picks up the phone, switch B formulates an answer message (ANM), identifying the intended recipient switch (A), the sending switch (B), and the selected trunk.

11. Switch B selects the same A link it used to transmit the ACM (link BX) and sends the ANM. By this time, the trunk also must be connected to the called line in both directions (to allow conversation). 12. STP X recognizes that the ANM is addressed to switch A and forwards it over link AX. 13. Switch A ensures that the calling subscriber is connected to the outgoing trunk (in both directions) and that conversation can take place. 14. If the calling subscriber hangs off first (following the conversation), switch A will generate a release message (REL) addressed to switch B, identifying the trunk associated with the call. It sends the message on link AW.

15. STP W receives the REL, determines that it is addressed to switch B, and forwards it using link WB. 16. Switch B receives the REL, disconnects the trunk from the subscriber line, returns the trunk to idle status, generates a release complete message (RLC) addressed back to switch A, and transmits it on link BX. 17. STP X receives the RLC, determines that it is addressed to switch A, and forwards it over link AX. 18. On receiving the RLC, switch A idles the identified trunk.

STPSCP

1.A subscriber served by switch A wants to reserve a rental car at a company’s nearest location. She dials the company’s advertised 800 number. 2. When the subscriber has finished dialing, switch A recognizes that this is an 800 call and that it requires assistance to handle it properly. 3. Switch A formulates an 800 query message including the calling and called number and forwards it to either of its STPs (e.g., X) over a link to that STP (AX). 4. STP X determines that the received query is an 800 query and selects a database suitable to respond to the query (e.g., M).

5. STP X forwards the query to SCP M over the appropriate link (MX). SCP M receives the query, extracts the passed information, and (based on its stored records) selects either a real telephone number or a network (or both) to which the call should be routed. 6. SCP M formulates a response message with the information necessary to properly process the call, addresses it to switch A, picks an STP using a link (e.g., MW), and routes the response. 7. STP W receives the response message, recognizes that it is addressed to switch A, and routes it to A over AW. 8. Switch A receives the response and uses the information to determine where the call should be routed. It then picks a trunk to that destination, generates an IAM, and proceeds (as it did in the previous example) to set up the call.