1 General Safety Rules Mr. Lombardi. 2 Safety These rules are in place to help you keep from hurting yourself and others.

Slides:

Advertisements

Similar presentations

Automotive Shop Safety

Advertisements

AG Mech Safety Skills. Objectives To understand the safety skills used in AG Mech. To understand the safety skills used in AG Mech. To understand the.

1 Lathe Safety By: Phil Brooks February 10, 2009 Chicago Woodturners.

Machine Shop Hazards, Machine Tool Safety

STEM Room 305 Mrs. Barbour.

1 Part 1 Directions: As your instructor goes the safety rules for the lab, write down the missing word or words in the blank spaces on your study guide.

WOODSHOP SAFETY By James MacCabe Modified by Julie Doucette.

GENERAL SAFETY RULES JEOPARDY!

Stationary Power Tool Safety

Lab Safety Rules Chemistry.

General Classroom Rules Be in class on time and prepared to work Get your journal and sit in assigned seat No talking while instructor is talking Raise.

2 3 4 One of the most common type of workplace injuries is those incurred from manual handling. To prevent manual handling injuries an employer needs.

Safety. An unplanned event that may or may not result in an injury What is an Accident?

Band Saw Safety Rules. Safety Rule #1 Keep all guards in place. Keep all guards in place.

2.1. INTRODUCTION Safety should be uppermost in the minds of all machine technology workers. It should become a state of mind so that reactions become.

Manufacturing Technology Safety: Band Saw. Safety Rule #1  Keep all guards in place.

 Diagnose, adjust, repair, or overhaul small engines used to power lawn mowers, chain saws, recreational sporting equipment and related equipment. 

Shop Safety and Conduct By: Mr. Beese. Safety In The Work Area Keep Work Area Clean Tools Put Away Fire Hazards can be avoided Shop Floor.

Engineering & Technology General Safety Rules

Lab and Tool Safety.

General SHOP SAFETY In technology education, SAFETY is regarded as essential for at least two reasons. #1 – The natural concern for people’s welfare.

JEOPARDY! HAND TOOLS $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100 $200 $300 $400 $500 $100.

Always wear SAFETY GOGGLES in the shop. Do not operate any machine unless authorized to do so and properly trained on it. Use the proper tool for the.

Chapter 1 Safety page 13.

SAFETY RULES Follow all directions the first time they are given. Be courteous in language and actions. Be on time and prepared to participate. Respect.

Copyright © Texas Education Agency, All rights reserved. Flexible Manufacturing Basic Safety 1.

Power Tool Safety Guidelines for Construction Trades Students.

Finishing Safety. When using stains, paints and other finishes Wear eye protection. Wear old clothing or cover your clothes Wear a respirator when spraying.

Miter Saw IMPORTANT SAFETY INSTRUCTIONSWARNING: Read all instructions before operating product. Failure to follow all instructions listed below may result.

Safety on Call ACCIDENT PREVENTION. Safety on Call WHY DO ACCIDENTS HAPPEN? Accidents happen for one or both of the following: – Unsafe acts – Unsafe.

General Shop Safety. When does complacency …

Shop Safety General Safety Procedures for Shop Objectives u Understand basic safety for the shop u Take quiz on safety procedures.

Matt H, 2010 Safety Captain, The Green Machine Team 1816.

Shop Safety Safety is everyone's business and responsibility.

Engineering Lab Landstown High School Safety Dance

Chop Saw. May not cause death but can cause severe injuries. May not cause death but can cause severe injuries. Loss of fingers or arms can occur Loss.

Safety Emily Condiff “Safety rules are your best tools”

SAFETY Or the many ways you can avoid hurting/killing yourself or someone else in this wonderful class.

Ms. Vallejo’s Technical Theater Safety Rules and Regulations

Ms. Wilson WOODSHOP SAFETY LESSONS & VIDEOS. BASIC SAFETY 1. Eye protection must be worn while using power equipment and bladed hand tools 2. No loose.

Bronson Hulbert. 1. Never alter a guard or use the tool with a guard missing. Be sure all guards are in place and working properly before each use. 4.

Write down three safety rules we talked about in the past few days. Talk with someone near you and see how many ways are out there to lift a car for service.

© Y. Cochrane What is a hazard?What is a hazard?  A hazard is any risk you may take that may endanger the health and safety of a person © Y. Cochrane.

Welding Safety What’s Wrong In this Picture?. © Business & Legal Reports, Inc. Session Objectives You will refresh your knowledge on how to: Protect yourself.

Power Tool Safety Don’t operate a machine until: A) receiving proper instruction B) you fully understand how to use it C) you have permission Always wear.

General Agricultural Mechanics Laboratory Safety Highlighted Notes.

Gracious Professionalism Personal Protective Equipment Safety in the Shop Tools and Their Uses Robot Safety What Do I Do If...?

SAFETY RULES AND PROCEDURES FOR POWER TOOLS INDEPENDENCE MIDDLE SCHOOL TECHNOLOGY EDUCATION DR. HURD 2010.

By James MacCabe Modified by Julie Doucette And Mr. Zajac.

General Personal and Lab Safety Practices

Safety at SM FIRST Lab.

Prepared by: Gp Capt Dr. Hamid Ullah Khan Niazi

Thaddeus Stevens College of Technology

Power Tool Safety Original Power Point Created by Jay Williams

Safety A top priority!.

Power Tool Safety Don’t operate a machine until:

Safety- Safety -Safety

Compressed Air Safety.

Kevin Kruemp. (Safety Captain)

PORTABLE POWER TOOLS and EQUIPMENT

Kitchen Safety.

2.0 – Shop Safety.

General Safety Procedures for Shop

General Safety Rules.

What You Don’t Know Can Hurt You.

Power Tool Safety.

Power Tool Safety Don’t operate a machine until:

General Shop Safety Thinking Safe… Prevents Injury!

Presentation transcript:

1 General Safety Rules Mr. Lombardi

2 Safety These rules are in place to help you keep from hurting yourself and others.

3 Safety State of Mind: No drugs/alcohol

4 Safety Wear proper clothing for the type of work being done

5 Protect your eyes, face, head, scalp, and ears. No Contact lenses!

6 Safety Avoid distractions & pay attention

7 Safety Keep the work area clean

8 Safety Use the correct tools for the job

9 Safety Work only at operating speed

10 Safety Keep tools clean and in good repair

11 Safety Repairing and cleaning power tools, power must be Off or Unplugged!

12 Safety Compressed Air Used for Cleaning Only machines and work surfaces Never bodies

13 Safety Keep guards in place

14 Safety Do not leave a machine running unattended

15 Safety Use safe blades and bits

16 Safety Misc: Ventilation Rags Storage Personal Tools

17 Safety Everyone gets a “Clean-Up” job

18 The End