Working to scale. When something is drawn the same size as its actual size, it is said to be drawn to scale 1:1 Draw the plan view of your pencil sharpener.

Slides:

Advertisements

Similar presentations

Camera Shots and Angles for Television Production Instructor: Mrs. Hudgens.

Advertisements

Graphic Communication

Technical Sketching and Drawing

Scales Floor Plans Scaling drawings allow us to draw exceptionally large objects such as houses on any size of paper available to us. To enable this to.

Yolanda López ESO 1 - TECHNOLOGIES. WHAT IS IT? A scale drawing represents something that is:  too large to be drawn to actual size OR  too small to.

Isometric and Oblique Pictorials

Orthographic Projection

Gummy Bear Lab. Bell Ringer Draw a gummy bear that is approximately 3-5 lines tall on your notebook paper. Label the length of the bear Label the width.

Scaling. Scaling is a skill used by many people for a variety of jobs Today we will learn this skill by making a scale model of the Statue of Liberty.

Geometry Scale. Geometry Scale is used when something that is drawn on paper is too large to fit, or is too small to be seen. For now we are going to.

Unit 2.Drawing applied to technology. What are we going to see in this unit?  2.1 Drawing tools and how to use them  2.2 Drafts and sketches  2.3 Drafting.

Scale Drawings & Models

DIEDRIC SYSTEM.

Bisecting a Line Segment. You want to bisect line segment PQ.

Sketching and Drafting Orthographically - Theory

Sketching Practice “One picture is worth a thousand words.”

MECHANICAL DRAWING.

4-2(B) Scale Drawing.

Below the Belt Above The Belt Head Shots Extremities.

LEARNING PLAN FOR MONSTER PROJECT Social Studies Objective:Students will use the monster project to locate a place on a map. Motivation:Have you ever.

Key things to know!. Everyone your age or older should be able to draw a rough world map without looking at one. Your task: Take your humanities book.

Scale Drawings & Models

Scale drawings. Scale drawings are used when it is unrealistic to think about drawing an object in its actual size; so we need to “scale” them down Observe…

Scale Drawings Taking a close look at the Statue of Liberty.

Multiview Drawing A multiview drawing is one that shows two or more two-dimensional views of a three- dimensional object. Multiview drawings provide the.

Using Drawings to Communicate Lecture 3 –How to create an isometric drawing of a part when given front, top, & right side views.

Pre-Algebra T McDowell

Unit 2.Drawing applied to technology. What are we going to see in this unit?  2.1 Drawing tools and how to use them  2.2 Drafts and sketches  2.3 Drafting.

Residential Floor Plans

Orthographic Drawings

Circle Terminology. Circle The set of points in a plane that are a fixed distance from a given point called the center of the circle.

How to read an Architect’s Scale

On a floor plan of her room, the length of Hailey’s bed is 3 inches. If the scale of her floor plan is inch = 1 foot, what is the actual length of her.

Portraiture Basic proportion. The Proportions of a Head - 1 The proportions of a head will vary from person to person and change slightly with age, there.

Objective WRITE IN AGENDA EVERY DAY Learn the principles of design by creating a look book Materials Needed Pencil Eraser 4 sheets of printer paper Sketch.

Still Life Drawing Today you will be using your sketchbook.

Drawing to Scale Chris Wakefield HTHMA. Why Draw to Scale? To create a drawing which is proportionately the same To create a drawing which is proportionately.

Elevation- an artistic drawing of the set from the audience’s point of view.

What is Drafting?.

Making Finger Joints.

How to read an Architect’s Scale

How to read an Architect’s Scale

Lesson 7-4 Pages Scale Drawings.

How to Read an Architect’s Scale

What is architecture, and what do architects do?

Deans Community High School

Sketching the Derivative

Visual arts daily objectives

Explain terms and procedures utilized in technical drafting

Human Proportions The basic guide for body proportion is in head lengths. The figure of an average adult is 7 to 7.5 head lengths: First head length:

Technological Drawings

You will need a pencil and something to write on.

How to Measure & Draw a Floor Plan to Scale

ENGN103 Engineering Drawing

The distance on the map or drawing or the actual distance.

Orthographic Sketch Solution

Technical Drawings Sketch by Leonardo DaVinci. 500 years ago.

Eye great ear head hair mouth It’s an ear. neck.

Great! on in in front of under above next to behind between next.

ENGN103 Engineering Drawing

2 types of scale factor problems

Multiview Drawing Orthographic Projection

Graphic Communication

S1 Orthographic Sketching

ENGN103 Engineering Drawing

SPRING TIME LINE RUBRIC

Presentation transcript:

Working to scale

When something is drawn the same size as its actual size, it is said to be drawn to scale 1:1 Draw the plan view of your pencil sharpener (from above) actual size. – Measure it, do not draw around it!

Working to scale When something is drawn twice its actual size, it is said to be drawn to scale 2:1 Draw the plan view of your pencil sharpener (from above) scale 2:1.

Working to scale When something is drawn half its actual size, it is said to be drawn to scale 1:2 Draw the plan view of your pencil sharpener (from above) at scale 1:2.

Measure one of your classmates to get the following measurements: Floor to waist (use belly button as fixed point) Waist to shoulder Shoulder to top of head Width of head from front Width of shoulders from front Width of waist from front Width of ankles from front Draw a sketch of your classmate at scale 1:25 (divide all real measurements by 25 to get the measurements you should draw).