New N1913A and N1914A EPM Series Power Meters High speed multi-channel measurement made possible! Agilent Restricted

Why should you consider migrating your existing E4418/19B to the new Agilent N1913/4A? Existing platform: E4418/9B Higher cost of ownership: More expensive at purchase. Higher running cost: calibration on a yearly basis Higher support cost Longer operation time, higher operation cost: Older platform with older user interface which make it harder to use. Lower number of reading/s System integration limitation Does not support new interfaces such as LAN and USB. Usage and application limitations: Only supports a limited set of power sensors. Only offer a maximum of 2 channels. Will no longer be orderable starting 1 Nov 2010. Agilent Restricted

What are the migration benefits? New platform: N1913/4A Low cost of ownership: Cheaper at purchase. Lower running cost: calibration only once every 2 years. Lower support cost: up to 30% on up front support (3 year and 5 years) promotion 1.056. Shorter operation time, lower operation cost: New intuitive easier to use user interface. 2 x Faster measurement speed System ready platform Full support of GPIB, LAN/LXI, USB interfaces offering full integration flexibility. Versatile platform: Support of a maximum number of power sensors. Up to 4 available channels to be used in various applications. Migration made easy Backward code compatibility with the E4418/9B 20% trade discount when replacing the E4418/9B with the N1913/4A Leverage of all your previous power sensors investments: E93xx, 848x, N848x… Financial solution to get easy and fast access to the new units: Easy Buy, Easy Rent, Easy Lease… www.microlease.com/agilent Already available for purchase Agilent Restricted

USB Host (U2000 sensor channel) See the improvements for yourself! N1913A/14A and E4418B/19B Outlook Comparison USB Host (U2000 sensor channel) Numerical keypad FRONT Color display REAR VGA Out Here is a outlook comparison on the new and old EPM. On the front panel, new EPM comes with high resolution color LCD display, USB host that support U2000 Series power sensor and numerical keypad for ease of value inputs to the power meter. On the rear panel, you can see a row of USB, LAN and GPIB connectivity, an optional VGA output for customer who needs to display result on a monitor. There is also pair of optional input/output trigger, and USB host for U2000 sensor. Trigger in/out USB, LAN and GPIB N1913A/14A EPM series E4418B/19B EPM series Agilent Restricted

New N1913A/14A EPM Series Power Meters New N1913A/14A EPM Series Power Meters Replacing the Popular E4418B/19B Power Meter High speed multi-channel measurement made possible! New N1913A/14A provide: Faster measurement speed, up to 400 readings/sec1 Up to 4 channels power measurements Support all Agilent average and CW sensors Code compatible with E4418B/19B and legacy 436A/7B/8A power meter2 USB master, to work with U2000 series USB sensor GPIB, LAN LXI & USB connectivity Smart Battery option – one push indicator function VGA output option Fast External Triggering option for power/frequency sweep function Software drivers for Labview (IVI-COM), Agilent VEE 2 years calibration interval The new N1913A/14A EPM power meters offer 400 readings per second measurement speed which is 2X faster than old EPM E4418B/19B. It is good news for customer who needs more than 2 channel measurement, new EPM offers the optional USB hosts that support U2000 Series sensors. For peace of mind for migration, new EPM supports all Agilent average and CW sensors, what is more, it is backward code compatible with E4418B/19B and the legacy 436A/7B/8A power meter. New EPM supports the popular U2000 Series sensors, just plug in the U2000 Series, new EPM will recognize and communicate with U2000 Series sensor, measure results can be displayed on new EPM. Besides GPIB, new EPM come with standard LAN and USB connectivity which is not available in old EPM. You will be able to know the battery level by just one touch on the battery, you no longer need to turn on the power meter to check the battery level. Does your customer need to show result on a monitor? The VGA output will fit the purpose. Lastly power and frequency sweep make easier and faster using the external input and output trigger. 1. Comparing to E4418B/19B using E-Series power sensors, 2. Need to purchase optional emulator software for 436A/7B/8A Agilent Restricted

Product Briefing for N1913A/14A and E4418B/19B Specifications & Features Measurement Channel 1 or 2-channel (additional 2-channel via USB sensor ports, optional) 1 or 2-channel Measurement speed 400 readings/s 200 readings/s Instrumentation Accuracy +/-0.5% 1mW ref accuracy +/-0.4% Calibration interval 2 years 1 year External Connectivity GPIB, LAN (LXI), USB GPIB, RS232 Sensor support E-9300, E4410, 8480, N8480 series and U2000 USB sensors E-9300, E4410, 8480, N8480 series Display Color Mono Data Input Device Numeric keypad Conventional 4-key (up, down, left, right) Battery Life (optional) 7.4hrs (backlight off), 6hrs (backlight off) Fully charged in 2.2hrs from empty stage 5.5hrs (backlight off), 3.5hrs (backlight on) Fully charged in 2hrs from empty stage VGA, External Trigger In/Out (optional) Yes N/A Physical Dimension 212.6mm W x 88.5mm H x 348.3 D (8.5 in x 3.5 in x 13.7 in) Weight N1913A: 3.6kg (8.2lb) N1914A: 3.7kg (8.4lb) E4418B: 4.0kg (8.8lb) E4419B: 4.1kg (9.0lb) This table compares the performance and features between new N1913A/14A EPM and old E4418B/19B EPM. The key improvements are circled in red, and will be further discussed later. Agilent Restricted

N1913A/14A Product Support Strategy Support Warranty Standard 1 year warranty Optional R-51B-001-3C extended 3 years Optional R-51B-001-3C extended 5 years Repair & Calibration 2 years calibration interval (E4418B/19B has 1 year calibration interval) Repair & Calibration offered at WCSS centre, ready 8 weeks after SHIP Upfront 1.056 Full Service promotion Support Parts at SPO Support Parts setup in SPO system for replacement and repair Migrate from E4418B/19B Check out the migration guide : http://cp.literature.agilent.com/litweb/pdf/5990-4016EN.pdf New EPM offer up to 5 years warranty and 2 years calibration interval. Customers wish to migrate from old E4418B/19B to N1913A/14A can refer to the migration guide. Agilent Restricted

Protect your investment with the widest range of power sensors support.

Key benefits. Perform 3-port or 4-port measurement on a single power meter Test case: Scalar Network Measurement on a power meter Improve test time up to 60% when stepping power, and 22% when stepping frequencies. Test case: Faster Power and Frequency Sweep Measurement Remotely control power measurement. Test case: Remote Power Monitoring Agilent Restricted

SCPI Commands Available in N1913A/14A, Not in E4418B/19B Migration guide : http://cp.literature.agilent.com/litweb/pdf/5990-4016EN.pdf. N1913/14A E4418/19B Comments CALCulate[1]|2|3|4:HOLD:STAT <character_data> Not available This command sets the hold value to be either minimum or maximum of the power measured. This is new feauture requirement to hold the CW/average power. CALCulate[1]|2|3|4:FEED[1]|2 This command sets the input measurement mode to be fed to the specified input on the CALC block. It is applied to the measurement after the CALC:MATH:EXPR command has been used to specify which channel the feed is taken from. Reserve for time gating function in future (USB sensor) CALibration 3|4:ZERO:TYPE EXTernal|INTernal This command is used to configure the U2000 series power sensor either for external zeroing or internal zeroing. OUTPut:RECorder[1]|2:FEED <data_handle> This command specifies which measurement is sent to the recorder output specified by the numeric value following RECorder. New feature for N1913/14A. Any channels can be assigned to become recorder A or B OUTPut:TRIGger[:STATe] <boolean> This command enables or disables the trigger output signal. E4418/19B does not have the Trigger output [SENSe[1]]|SENSe2:BUFFer:COUNt This command sets the buffer size for average trigger measurement. It must be used in conjunction with external trigger. [SENSe[1]]|2|3|4:CORRection:FDOFfset:UNIT This command allows command and query access to the Frequency Dependency Offset (FDO) unit New feature allow user to change the unit dB or %. E4418/19B only allow in % [SENSe[1]]|SENSe2:FREQuency[:CW|:FIXed]:STARt This command sets the start frequency of frequency sweep. It must be used in conjunction with external trigger. Not available on E4418/19B [SENSe[1]]|SENSe2:FREQuency[:CW|:FIXEd]:STEP This command sets the number of steps in frequency sweep. It must be used in conjunction with external trigger. Not available on E4418/19B [SENSe[1]]|SENSe2:FREQuency[:CW|:FIXed]:STOP This command sets the stop frequency of frequency sweep. It must be used in conjunction with external trigger. Not available on E4418/19B New EPM offer up to 5 years warranty and 2 years calibration interval. Customers wish to migrate from old E4418B/19B to N1913A/14A can refer to the migration guide. Agilent Restricted

SCPI Commands Available in N1913A/14A, Not in E4418B/19B Comments SYSTem:COMMunicate:LAN commands Not available These control the settings for the LAN interface which is not available in E4418/19B SYSTem:DISPlay:BMP This command returns the display image in bitmap format. Not available in E4418/19B. This command is limited to a maximum of five image returns per second. SYSTem:HELP:HEADers? This query returns a list of all SCPI commands supported by the instrument. SYSTem:LICense:INSTall This command will install the valid licensed option according to the license string. Not available in E4418/19B. SYSTem:LICense:LIST? This query will return all the installed license string (for the options). Not available in E4418/19B. SYSTem:LICense:REMove This command will remove the valid installed option according to the license string. INITiate:CONTinuous:ALL Sets all trigger sequences to be continuously initiated INITiate[:IMMediate]:ALL This command initiates all trigger sequences This new added feature in N1913/14A TRIGger[:SEQuence[1]|2|3|4]:SLOPe This command specifies whether a trigger event is recognized on the rising or falling edge of a signal (only on the etxernal trigger source). TRIGger[:SEQuence[1]|2|3|4]:COUNt This command controls the path of the trigger subsystem in the upward traverse of the wait for trigger state. COUNt loops through the event detection/measurement cycle are performed. That is, COUNt measurements are performed in response to COUNt trigger events Applicable in FAST mode only. TRIGger[:SEQuence[1]|2|3|4]:DELay:AUTO This command is used to determine whether or not there is a settling- time delay before a measurement is made. TRIGger[:SEQuence[1]|2|3|4]:IMMediate This command provides a one time over- ride of the normal process of the downward path through the wait for trigger state. Trigger source on bus or hold only SERVice:BACKlight:BRIGhtness This command sets the intensity of front panel’s backlight. E4418/19B does not have this feature on the LCD control. SERVice:BACKlight:MODE This command sets the mode of front panel’s backlight to ON, OFF or TIMED. When TIMED mode is selected, the backlight will turn off within 10 minutes after the last keypress. Press any keys on the front panel to turn the backlight on again. New EPM offer up to 5 years warranty and 2 years calibration interval. Customers wish to migrate from old E4418B/19B to N1913A/14A can refer to the migration guide. Agilent Restricted

SCPI Commands Available in N1913A/14A, Not in E4418B/19B Comments SERVice:BIST:commands Not available These command enables/disables the Built In Self Test (BIST) for calibrator, linearity and zero set tests. This is new added feature in N1913/14A. E4418/19 runs the builtin test during power up SERVice:CALibrator:ADJ: commands These command adjust the 1 mW calibrator output in coarse scale or fine scale SERVice:DISPlay:VGA This command enables or disables the state of VGA output This is new added feature in N1913/14A for the VGA option. SERVice:DISPlay:BSCReen commands This command enables or disables the Blank Screen and Secure Blank Screen features of the front panel display. SERVice:FAN:FULL This command set the fan controller to run at full speed. At the first power- up, the default state is ON. If the user sets the state to OFF and power cycle, the state will be saved. On the next power cycle, the state will be set to OFF. SERVice:LAN:PHOStname This command preset the LAN hostname to its default value. It requires the serial number to be set- up. SERVice:SECure:ERASe This command erases the EPM Series power meter’s memory, for example, before you return it to Agilent Technologies for repair or calibration, of all data stored in it. SERVice:SENSor[1]|2:CALFactor <cal_factor_data> This command writes calibration factor data to, or reads calibration factor data from, the currently connected sensor. The whole calibration factor block must be written at once as a checksum is generated. The new block must not be larger than the existing block. This command applies to the following sensors: • E4410 Series • N8480 Series (excluding Option CFT) • E9300 Series SERVice:SENSor[1]|2|3|4:FREQuency commands These query returns the maximum/minimum frequency that can be measured by the currently connected sensor. It is applicable to E- Series sensors only. Maximum frequency information is stored in the sensor’s EEPROM SERVice:SENSor[1]|2|3|4:POWer:AVERage:MAXimum? This query returns the maximum average power that can be measured by the currently connected sensor. It is applicable to E- Series sensors only SERVice:SENSor[1]|2|3|4:POWer:USABle commands returns the maximum/minimum power that can be accurately measured by the currently connected sensor. SERVice:SENSor[1]|2|3|4:RADC? This query returns a new raw uncorrected measurement in volts, as a 32 bit signed integer SERVice:SENSor[1]|2|3|4:TNUMber? This query returns the tracking number for U2000 Series and E- Series sensors. Tracking number information is stored in the sensor’s EEPROM SERVice:STATe <boolean> This command enables or disables the warm start feature New EPM offer up to 5 years warranty and 2 years calibration interval. Customers wish to migrate from old E4418B/19B to N1913A/14A can refer to the migration guide. Agilent Restricted

SCPI Commands Available in E4418B/19B, Not in N1913A/14A Comments Not available CALibration[1|2]:ECONtrol:STATe <Boolean> This command is used to enable and disable the rear panel TTL zero/cal inputs. The TTL inputs provide an external means to initiate ZERO and CAL cycles. N1913/14A does not have the remote TTL I/O DISPlay:CONTrast <numeric_value> This command is used to control the display contrast. N1913/14A Color LCD does not contrast control, only backlight control OUTPut:TTL[1|2]:OUTPut:TTL[1|2]:FEED <string> This command controls whether a window limits fail drives the rear panel TTL Output HIGH or LOW. N1913/14A does not have the TTL out limit function OUTPut:TTL[1|2]:FEED <string> This command controls whether an asserted rear panel TTL Output indicates a failure in the upper, lower or either limit for the chosen window. OUTPut:TTL[1|2]:STATe <Boolean> This command is used to enable and disable the rear panel Upper and Lower window TTL Outputs. [SENSe[1]]|SENSe2:LIMit:CLEar commands used to clear any limit failures in E4418/19B. Not supported in N1913/14A Other [SENSe[1]]|SENSe2:LIMit commands This feature is not supported in N1913/14A SYStem:COMMunicate:Serial commands These control the settings for the RS232/RS422 serial interface which is not available in N1913/14A SYSTem:RINTerface GPIB|RS232|RS422 This command allows the remote control interface to be selected from GPIB, RS232, and RS422. N1913/14A does not need to select the interfaces , will auto detect & configure which interface to use SERVice:OPTion <string> This command loads the power meter memory with the options fitted. The query form of the command can be used to determine which options are fitted to the unit. For N1913/14A, user can use the *opt? query SERVice:SNUMber <alpha_numeric> This command is used to load the power meter with a serial number in the form GB12345678 or US12345678. For N1913/14A, user can only query the serial number: SERVice:SENSor[1]|2|3|4:SNUMber? New EPM offer up to 5 years warranty and 2 years calibration interval. Customers wish to migrate from old E4418B/19B to N1913A/14A can refer to the migration guide. Agilent Restricted

Resources for N1913A/14A Where to Find the Details? For support: QFS: http://field-bid.marketing.agilent.com/file_library/N1913_4A%20QFS_direct.pdf PMPS Brochure: http://cp.literature.agilent.com/litweb/pdf/5989-6240EN.pdf PMPS DM: http://cp.literature.agilent.com/litweb/pdf/5989-7837EN.pdf Data sheet: http://cp.literature.agilent.com/litweb/pdf/5990-4019EN.pdf User’s guide: http://cp.literature.agilent.com/litweb/pdf/N1913-90001.pdf Programmer’s guide: http://cp.literature.agilent.com/litweb/pdf/N1913-90008.pdf Installation guide: http://cp.literature.agilent.com/litweb/pdf/N1913-90010.pdf Service guide: http://cp.literature.agilent.com/litweb/pdf/N1913-90009.pdf Migration guide : http://cp.literature.agilent.com/litweb/pdf/5990-4016EN.pdf. Where to Find the Details? Website: www.agilent.com/find/epm For support: Contact your local Agilent office http://www.home.agilent.com/agilent/contactInformation.jspx?cc=US&lc=eng&nid=-11143.0&pageMode=HB&tmprop=TM The top sales tools that you can bring along when visit customer are quick fact sheet, brochure and direct mail. These sales tools have the necessary key points needed to promote N1913A/14A and the power meter and sensors products. For customer who wants to know more details of the N1913A/14A performances and usability they can refer to the data sheet and user’s guide. The installation guide, programming guide and service guide will be most useful after customer has purchased the N1913A/14A. You can also visit our internal web site to obtain more details of the N1913A/14A. For external customer, the jumpstation is the one step link to the N1913A/14A product collection page. Agilent Restricted

Product Options Model / Option Description N1913A/N1914A Single/dual channel average power meter N1913A/14A-102 Single/dual channel average power meter, battery N1913A/14A-103 Single/dual channel average power meter, battery, 2 rears USB ports N1913A/14A-104 Single/dual channel average power meter, VGA N1913A/14A-105 Single/dual channel average power meter, battery, 1 front 1 rear USB ports, VGA N1913A/14A-106 Single/dual channel average power meter, 1 front 1 rear USB ports N1913A/14A-107 Single/dual channel average power meter, external trigger in/out N1913A/14A-108 Parallel rear panel sensor input connectors and front panel reference calibrator connector, 2 rear USB ports N1913A/14A-109 Parallel rear panel sensor input connectors and rear panel reference calibrator connector, 2 rear USB ports N1913A/14A-200 436A & 437B code compatibility Agilent Restricted

E4418B and E4419B Discontinue Plan E4418B/19B Disco Start 2 Aug 2010 E4418B/19B Last Order Date 1 Nov 2010 E4418B/19B Last Ship Date 1 Feb 2011 E4418B/19B Obsolete 2 Nov 2015 MAY 2009 JUN 2009 JUL … AUG 2010 SEP OCT NOV DEC JAN 2011 FEB DEC 2011 2012 2013 2014 2015 2016 2017 Launch N1913A/14A (9 Jun 09) 5 Years Support Life The old EPM E4418B/19B will be officially discount starting 2-August-2010, providing customers especially from the aerospace and defence sector sufficient time to switch to the new EPM N1913A/14A. The last order date for old EPM is 1-Nov-2010, with last ship date falls on 1-Feb-2009. Old EPM will be completely obsolete on 2-Nov-2015 which is more than 6 years from now. Agilent Restricted

Why Choose the New N1913A/14A? High speed multi-channel measurement made possible! Protect your long term investment: Backward compatible with E4418B/19B, 436A, 437B and 438A power meters Widest power sensors support (compatible with all Agilent CW and E-Series power sensors) Reduce time to market: 2 times faster than E4418B/19B. Calibrate only once every 2 years. Reduce cost of ownership Versatile platform. Can be used for many different applications. Trade in your old E4418B, E4419B, 435B, 436A, 437B, 438A, 8990A and 8991A power meters and receive 20% discount on your N1913A and N1914A purchase. Find out more: www.agilent.com/find/pmpromo. Upfront 1.056 Full Service promotion Financial solutions: Easy Buy, Easy Rent, Easy Lease… www.microlease.com/agilent Agilent Restricted

Q and A Session THANK YOU Agilent Restricted