Design Review RSXS - EndStation Review on Vacuum Chamber Stand and Supports Location Beamline 8.0.1 Roll-up Endstation.

Slides:

Advertisements

Similar presentations

Tagger and Vacuum Chamber Assembly Procedure. Outline. Assembly procedure for tagger and vacuum chamber. Support stands. Alignment.

Advertisements

General Information Dimensions · Structure Width: ~ 197in. (16.4’), 99in. (8.2’)/car · Slope Angle: 5 degree · Structure Height (Front): 100in. + base.

Assembly Instructions DucoSlide Luxframe Controllable TOP BOTTOM L.H. R.H. Control side FRONT SIDE in open position REAR SIDE in open position 1.

TIGERBOT MECHANICAL DESIGN Kyle Backer (EE), Jeremy Jensen (ME), Matthew DeCapua (EE), Eric Walkama (ME), Mike Thomas (EE), Jonathan Cormier (CE), John.

BARTOSZEK ENGINEERING 1 The Design of the Booster Collimators Larry Bartoszek BARTOSZEK ENGINEERING 3/10/03.

HFA 2230 Series Horizontal to Incline Conveyor The 2230 Incline Conveyor features a a low profile yet extremely rigid anodized extruded aluminum frame.

Mechanical Engineering Design Review BL ARPES Endstation Derek Yegian, Jonathan Denlinger, Keith Franck 4/18/2008.

Test Chamber Assembly, 1.5M Long (59.00”) Vacuum Tube, 4.00 OD x 3.50 ID Vacuum Tube, 3.75 OD x 3.51 ID 3.375” CFF, Non-Rotatable Feedthrough, Ceramtec.

Structural Collapse Technician Training

Rolling element bearings A. Lozzi 2012

Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD.

1 TCS Lab Motors-2 (10/20/03) Design Changes since Version-1 1)Changed Encoder: now using R135S-03600Q-5L16C18TP-04EN 2)Eliminate Outriggers: Retain bolts.

Tagger and Vacuum Chamber Design. Outline. Design considerations. Stresses and deformations. Mechanical assembly.

TAGGER MAGNET DESIGN Presented by Tim Whitlatch Hall D Tagger Magnet Design Review July 10,

1 Status of infrastructure MICE Video Conference, August 17, 2005 Yury Ivanyushenkov Applied Science Division, Engineering and Instrumentation Department.

Mounting arrangement for the Solid Absorber. This contains mounting arrangement for:- 1. Handling and lifting from manufacturer’s place to RAL; 2. For.

Vbine Energy Generator Assembly Pictures and Info Slide Show.

Rolling element bearings A. Lozzi 09

How to support a shaft? The motor just turns the shaft. It doesn’t provide any support.

Tagger and Vacuum Chamber Design. Outline. Design considerations. Stresses and deformations. Mechanical assembly.

APPENDIX A (RFI) FOR THE FABRICATION OF MULTIPLE STEEL REACTION STRUCTURES FOR NASA-MSFC STRUCTURAL TESTING Mike Roberts 12/2/09.

DELTA Quadrant Tuning Y. Levashov, E. Reese. 2 Tolerances for prototype quadrant tuning Magnet center deviations from a nominal center line < ± 50  m.

Front Suspension Greg Habiak, Nicole Simon, Joe Vuto.

SOL-GEL COATING FACILITY CONCEPTUAL DESIGN REVIEW October 19, 2005.

dsdfsa Zoomed in view… Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD.

Merlin EPU Support and Drive System Design Review Steve Marks Mark Coleman 4/26/06.

Robotics – 8. Plates (2-sizes) Plate with holes on 0.500" increments and 1/8" diamonds in between. Can be cut on 0.500" increments. Available in two sizes.

NCSX Modular Coil Turning Fixture FDR. Background Modular Coil winding forms are cast structures which provide the foundation on which the coils are constructed.

MERLIN BEAMLINE RIXS refocusing mirror system D. Yegian

Perry Lapper Progress. Frame With Actuators Outside Frame.

Suspension D.J. Conroy.

CLIC Permanent Magnet Quadrupole update 1 st December 2010 Mechanical Engineering status N. Collomb1.

Mechanics of Materials. To determine the loading on a body Draw a free body diagram indicating – external loads and moments – reaction loads and moments.

1 COMPTON POLARIMETER PRELIMINARY MAGNET DESIGN 06/03/08 Christopher Vidal, Senior Mechanical Designer Ernie Ihloff, P.E., Engineering Group Leader EE.

ZDC Remote Handling Tool Structure and Force Analysis P. Debbins University of Iowa December 10, 2009.

XLP–6 Low Profile Car Carrier New Product Presentation.

MERLIN RIXS Endstation Design Review

FETS meeting Beam Profile Measurement Tank By P. Savage 13th June 2007.

CLIC Permanent Magnet Quadrupole Engineering Development of second family member Norbert Collomb, STFC Daresbury Laboratory 1N. Collomb 07/11/2012.

Oct 17, 2001SALT PFIS Preliminary Design Review1 Southern African Large Telescope Prime Focus Imaging Spectrograph Mechanical Mechanism Design Michael.

GlueX Two Magnet Tagger G. Yang University of Glasgow Part 1, 3 D Tosca analysis. Part 2, Preliminary Drawings. Part 3, Proposed Assembly Procedures (i)

1 Polarimeter build up and details Robert Lee. 2 View 1 Material (Removable plate, leg supports and rail guide spacer): Aluminum Leg supports attached.

Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.

Engineering Division 1 HHMI 8.2.X Endstation Modification Review Allan DeMello 12/13/2006.

Shear Test Assembly update

Exit slit toroid, with horizontal steering servo-loop to slits monochromator, with mirror and grating scanning Beamline Mono residual steering effects.

Systems Level Demo P15010: Arc Wheelchair Swing. Maggie Bates BS/ME Industrial & Systems Engineering Owen Breese BS Mechanical Engineering Elizabeth Cutolo.

LAUNCH X improvements. LAUNCH ©Auto Testing Division Content Sensor headProgrammeTarget dataClampsCabinetTurn table, Side slip.

The Hyatt Regency Walkway Collapse Presented By: Jonathan Foster 4/9/02.

WeldingRod’s Exactly Constrained 3D Printer Plate Identification and Stuffing.

Mu2e Protection Collimator, PC Andy Stefanik January 19, 2016.

HQ02a Magnet Interfaces at FNAL D.W. Cheng 3/6/2013.

The HiLumi LHC Design Study is included in the High Luminosity LHC project and is partly funded by the European Commission within the Framework Programme.

Tagger and Vacuum Chamber Design Jim Kellie Glasgow University.

ROLLING Rolling is a process of reduction of the cross-sectional area or shaping a metal piece through the deformation caused by a pair of metal rolls.

STEP 1: ASSEMBLE INSERT PLATES 1.Assemble insert plates by press fitting roller bearing and adapter plate into assembly 1.1 Prep all mating surfaces to.

VIEW SERIES with Sliding Door

Macromizer Wheelbase Design EJL

Rolling element bearings A. Lozzi 2012

Solenoid Yoke Door-Barrel Connection

Present status of the flux return yoke design

IR Detector - Test cryostat : Machining

iSHELL Design Review Cryostat & Optics Bench

SHMS Downstream Beamline Large SHMS/HMS Angles (Config-1)

Beam Finder Wire Assembly Undulator System

McMaster linear bearing #6709K180 with guide rail suppressed

Mechanical System P09045: Membrane Characterization Test Stand

Senad Kudumovic Design engineer

SNS PPU Cryomodule Space Frame

Transverse Shear Objective:

Presentation transcript:

Design Review RSXS - EndStation Review on Vacuum Chamber Stand and Supports Location Beamline Roll-up Endstation

All critical points coordinates shown on this drawing come from “ Jonathan Denlinger” spreadsheet with No. H22 and No. V11 updated: 11/19/ Critical Points Assy. Dwg. No. 26E828

RSXS Endstation Assy. Beam left to right Height 92”- from casters to top of cryostat. Cryostat fully extended in 150mm Width with swivel casters - in beam direction 69” x 54”

Beam is red Beam enter chamber at 5 degree

Chamber H = 28.5” 26” O.D ” I.D..188” wall Width: flange to flange = 30” max. Weight: (335 lbs)

Chamber Entrance Flange 6” cf Exit Flange 12” cf Top Flange 8” cf Bottom Flange Rect. Opening 17” x 14”

Chamber Support Plate Support Height = 5.0” Plate Thickness = 1.25” Width = 38” x 38” Through I.D. = 23” x 19.5” Weight = 345 lbs. Strut Tap = ¾-10 unc Lifting Eye Tap = ¾-10 unc Material = Steel

Stand: H = 28” Width: In beam direction 53”x47” Material: Steel Weight: (345 lbs)

Moving & Support Overall Estimated Weight: 2,450 lbs. Moving Low Profile Swivel Leveling Casters Recommended Load Capacity with 4 Casters 7,920 lbs Support Swivel Leveling Pads ¾-10 unc Threaded Rod with Flange Nut and Spacer Washer Pad Load=7,400 lbs ea.

6 Struts Support 3/4” – Turnbuckle 4 struts – 11” long 2 struts – 18” long Radial static load capacity: Rod End = 10,000 lbs.

All 6 Struts are Motorize

Vertical Slide Modified version of Tom Miller’s, slide on Beamline 4.0.3, from (ALM) American Linear Manufacturers Some of the new spec.: -2” of stroke -47mm O.D. angle contact bearing = load 3150 lbs. max. -1” O.D. roller ballscrew.250 lead = load 3250 lbs. max. -custom steel motor end plate for larger dia. Bearings and screw. -new strut mounting plate with two new tapper holes for screws to be used as hard stop.

Horizontal Slide The same slide used on BL M301 mirror system from (ALM) American Linear Manufacturers ALM part: # SPA Some of the spec.: -2” of stroke series crossed roller bearing -Precision rolled leadscrew with anti-backlash leadscrew nut -Nema 23 series frame motor mount and flex coupling -Photo optical limit switches

Horizontal Slide Assembly