USING SPECIAL TOOLS l Chapter 6 l Lab Manual l Page 133 CBC AUTOMOTIVE RK.

Slides:

Advertisements

Similar presentations

Machine Descriptions etc. Machine Tool Paul Streff Clark High School.

Advertisements

Measurement Quiz Click here to start Scoring

Tools and Measuring Instruments

Model 12 Intek Horizontal OHV

Teknik Kendaraan Ringan Dasar Kompetensi Kejuruan

5/12/20151 Exp.3: Micrometers &Feeler, Pitch, Radius and Dial gauges Exp.3.

Lesson 3 Measuring Engine Components and Specifications.

New Mexico FFA Agricultural Mechanics Career Development Event Engine Power.

Model 12 Intek Horizontal OHV Crankcase Disassembly and Assembly Lab #7.

Math Standards-You’re Teaching Them- Does Anyone Know?

Engine Measuring Vernier (Dial) Caliper Useful because it can read inside and outside measurements. Use only as a “rough” guide. Add the reading on the.

Measuring Tools and Systems

T-DAP MAP 32 WPP.

REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.

VALVE STEM INSTALLED HEIGHT CBC AUTOMOTIVE TECHNOLOGY.

Measuring Tools and Systems

Masonry Tools Flip Book Instructions. Step 1: You need 5 pieces of paper. Lined or plain will work. You also need a pen and a ruler. Draw a line down.

Tool Identification Power Technology. Standard Screw Driver.

LAB TOOLS Identification and Function. POUNDING TOOLS HAMMERS- TO USE TO STRIKE AN OBJECT AND WILL LEAVE SURFACE MARRING AND DENTS ON THE OBJECT HAMMERS-

INTAKE and EXHAUST SYSTEMS Chapter7 Classroom Manual Page 199 CBC AUTOMOTIVE.

© 2011 Pearson Education, Inc. All Rights Reserved Automotive Technology, Fifth Edition James Halderman IN-VEHICLE ENGINE SERVICE 27.

BASIC TOOLS & PROCEDURES

COMPANY PROFILE H K Machine Tools, Gali No 14, Near Ganesh Shop Factory, Bhikam Colony Ballabgarh.

PRECISION MEASURMENT. Vocabulary 1.British imperial (U.S.) Systems 11.) Metric system 12.)inside micrometer 3.Psi 13.)dial caliper 4.Foot- pounds.

Precision Measurement

SEALING the ENGINE n Chapter 5 n Classroom Manual –Page95 n Lab Manual –Page 113 CBC AUTOMOTIVE RK.

Measuring Engine Components and Specifications

Tools Purchase tools of highest quality. Craftsman, snapon, Kobalt, S&K, etc.. Purchase only those that have lifetime warranty. Keep tools clean and organized.

Unit A 6-3 Mechanical Systems and Technology. Problem Area 6 Agricultural Power Systems.

Manual Transmissions.

Technology Engineering I & II. Hand Tool Identification.

Small Engine Tools. Categories Small engine tools can be divided into three categories. 1.Mechanics tools 2.Measuring tools 3.Special tools.

Measuring Engine Components and Specifications. Next Generation Science/Common Core Standards Addressed! CCSS.ELA Literacy.RST.9 ‐ 10.3 Follow precisely.

INDUSTRIAL TECHNOLOGY-METAL ASSOCIATED THEORY TOPICS

Measuring Systems and Tools 11 Introduction to Automotive Service James Halderman Darrell Deeter © 2013 Pearson Higher Education, Inc. Pearson Prentice.

GENERAL ENGINE DIAGNOSIS n Chapter 4 n Classroom Manual –Page 73 n Lab Manual –Page 77 n Tasks I-A-1 thru I-A-8 CBC AUTOMOTIVE RK.

Hand Tools and Shop Equipment

© 2011 Pearson Education, Inc. All Rights Reserved Automotive Technology, Fifth Edition James Halderman MEASURING SYSTEMS AND TOOLS 12.

ENGINE REASSEMBLY Chapter 12 Classroom Manual page 311

The English System of Measurement

CHAPTER 7 MEASUREING SYSTEMS AND TOOLS

Instructor: James Thornburgh

Your instructor: Phil Fournier, ASE certified Master Technician Automotive Engine Performance.

TCS CONFIDENTIAL EIS ILP Lab NPD Lab orientation.

Automotive Engines: Theory and Servicing, 7/e By James D. Halderman Copyright © 2011, 2009, 2005, 2001, 1997 Pearson Education, Inc., Upper Saddle River,

Home Small Gas Engines1 Tool Identification. Home Small Gas Engines2 Micrometer.

MIRACLE WORKERZ TRAINING COURSE Introduction to Hand tools.

MEASURING SYSTEMS AND TOOLS

Long Island P-Tech Manufacturing.

1 VERNIER CALIPERS 2. USING MEASURING INSTRUMENTS PROPERLY

Chapter 4 Shop Tools.

Automotive Engines Theory and Servicing

Small Engine Tool ID Part 1.

Exp.3: Micrometers &Feeler, Pitch, and Radius gauges

Your Sourcing partner For Fasteners & machined Components

FIGURE 7-2 A plastic rule that has both inches and centimeters

Introduction To Engineering Bike Lab 1 – 2 Procedure

Mach 112 Cutting Tools & Measurement

Exp.3: Micrometers &Feeler, Pitch, and Radius gauges

Dimensions and Tolerances

Dimensions and Tolerances

Automotive Technology Principles, Diagnosis, and Service

Automotive Engines Theory and Servicing

Measuring Systems and Tools

Chapter 6 Measuring.

Turn to page 30 in the Airframe & Power plant Mechanics general handbook.

Presentation transcript:

USING SPECIAL TOOLS l Chapter 6 l Lab Manual l Page 133 CBC AUTOMOTIVE RK

Due this week l How the Engine Works l Chap 2 Questions l Micrometer Training on Computer l Engines Reassembled and returned to “Z” building l Engine Spec Sheet turned in. l Tool boxes and special tools.

OBJECTIVES l Demonstrate proper procedure using a feeler gauge. l Demonstrate proper use of a vernier or dial caliper. l Demonstrate the proper use of micrometers. l Demonstrate the proper use of dial indicators. CBC AUTOMOTIVE RK

OBJECTIVES l Demonstrate the proper use of cylinder bore dial gauge. l Describe the use of special hand tools. l Demonstrate the proper use of service manuals. CBC AUTOMOTIVE RK

ENGINE MEASURING TOOLS l Using feeler gauges l Reading the Vernier Caliper l Reading the Dial Caliper l Reading a Micrometer - page 135 l Using a Dial Indicator - page 138 CBC AUTOMOTIVE RK

USING A CYLINDER DIAL BORE GAUGE l Page 140 CBC AUTOMOTIVE RK

SPECIAL HAND TOOLS l Using a torque wrench l Torque-to-yield- page 141

SERVICE MANUALS l VIN - See handout l page 142