Coal Bed Methane by Widodo W. Purwanto a Departemen Teknik Kimia b Pengkajian Energi Fakultas Teknik Universitas Indonesia

Content What is coal bed methane? CBM resources CBM production Water management CBM economics

What is CBM? Coal Bed Methane is naturally occurring methane (CH 4 ) with small amounts of other hydrocarbon and non- hydrocarbon gases contained in coal seams as a result of chemical and physical processes. It is often produced at shallow depths through a bore-hole that allows gas and large volumes of water with variable quality to be produced.

CBM vs. CMM Coalbed Methane is methane gas contained in coal. When this gas contains other constituents, it is sometimes referred to as coal seam gas. Coal Mine Methane is methane gas that is released from coal or surrounding rock strata during the process of coal mining

World CBM Resources Estimates for world coalbed methane range from 100 to 260 Tm 3. Collectively, Canada, Russia and China represent 80% of world resources. The largest coal producing countries are also endowed with coalbed methane resources, namely, Australia, the United States, Ukraine, Germany and Poland.

Indonesia’s CBM Resources

US CBM resources

What Controls CBM Production? The rate of CBM production is a product of several factors that vary from basin to basin fracture permeability development, gas migration, coal maturation, coal distribution, geologic structure, CBM completion options, and produced water management. In most basin areas, naturally developed fracture networks are the most sought after areas for CBM development. Areas where geologic structures and localized faulting have occurred tend to induce natural fracturing which increases the production pathways within the coal seam.

Geological aspect Unlike typical clastic and carbonate reservoirs, gases are not stored in the matrix porosity of a coal seam, but are adsorbed onto the surface of micropores This unusual storage system is much more efficient than conventional reservoirs, and a coal seam may hold up to twenty times the volume of gas found in a conventional reservoir of similar size, temperature, and pressure. The exact quantity of sorbed gas is controlled by the confining pressure and surface area of the micropore system. The macroporosity of coals is the cleat system. Cleating is a mining term that describes the naturally occurring fractures found in coal seams. Face cleats are more continuous, and control the flow of gas to a wellbore. Butt cleats, less continuous cleats that form perpendicular to face cleats, are associated with the diffusion of gas from the coal to the face cleats. Cleating is related to both the compaction of the coal and to any tectonic forces acting on it.

Typical production curves for a coal-bed methane well

Relative permeability of gas and water vs. water saturation within coal seams of the Warrior Basin, Alabama. As water saturation decreases, gas production improves as the relative permeability to gas improves substantially

Production of Gas – Coal bed vs. Conventional Reservoir

Life of well Conventional gas wells can produce from a few years to over 50 years. Well duration is affected by technology and as advances are made, reserves are recovered more quickly, which reduces the expected well life. Current estimates for the life of a CBM well vary from 5 to 15 years. CBM wells in the Wyoming portion of the Powder River Basin are estimated at only 7–10 years, while the Montana portion of the same basin was estimated at 10–20 years. Other basins have shown some longer production times, however it is generally feared by the public that basins may be relatively quickly pumped and then abandoned.

CBM Completion Methods CBM wells are completed in several ways, depending upon the type of coal in the basin and fluid content. Each type of coal (sub-bituminous to low-volatile bituminous) offer production options that are different due to the inherent natural fracturing and competency of the coal seams. The sub-bituminous coals are softer and less competent than the higher rank low-volatile bituminous coals and therefore are typically completed and produced using more conventional vertical well bores. The more competent higher rank coals lend themselves to completions using horizontal and vertical well bores.

Typical drilling activities

Drilling Method

Vertical and horizontal well bores

Production scheme of gas and water for a typical coalbed methane well

Enhanced production The CBM industry is exploring new methods of enhancing gas production from older fields that have produced for more than 10 years. Several companies are experimenting with the injection of nitrogen (N2) and carbon dioxide (CO2) into the coal bed to displace methane along the coal face cleats. Generally, the N and/or CO2 molecules replace the methane molecules within the cleats at a ratio of approximately 4 to 1. Coals can replace 25% to 50% of their methane storage capacity with nitrogen. This enhanced production method has a beneficial side effect—the sequestering of CO2. Carbon dioxide is a common by-product of many industrial processes and is considered a green house gas. There are some concerns, however, that injection of CO2 into mineable coals presents a safety hazard, as the mines are required to have a limit of 3% CO2 by volume in the mine air. One potential method for reducing CO2 levels in the mine air is to use a mixture of CO2 and other gases, such as nitrogen.

Difference in production rate by varying injected gas

Coal sorption isotherm

US CBM production

Gas compression & processing Gas produced from CBM wells requires dehydration to remove the water vapor in the gas, and is usually compressed 2 to 3 times before it reaches the sales line. CBM leaves the wellhead at relatively low pressures that range from 2 to 5 pounds per square inch/gauge (psig). The CBM first passes through a field compressor unit, typically a rotary screw compressor that will increase the gas to psig. At this pressure the gas flows through a gathering system on its way to the sales compressor. The sales compressor boosts the pressure to approximately 1200 psig. Following this stage the CBM in the sales line is transported locally or regionally to end-user sites, which are metered. As a CBM field matures, the CBM may contain increased levels of CO2 that needs to be removed prior to being transported to market. Gas processing plants installed on the pipelines typically in conjunction with sales compressors treat the natural gas and remove the CO2 and water vapor.

CBM surface facility

CBM to CNG, LNG, Electricity

Water Management

CBM Roadmap

Legal framework