1 © 3M 2011. All Rights Reserved. Confidential Information for the use of Network Rail 3M™ Peltor™ DECT-Com II Light-Weight Headset (MT701-H03) Fitting.

Slides:

Advertisements

Similar presentations

Checking your bike Checking your bike is quick and easy to do (you dont need to be a cycle mechanic). With practice it should only take a few minutes if.

Advertisements

Build Your Own Future RC2 Serviceability. Build Your Own Future Safety and Ground Rules Before servicing, always remove A/C power from the unit and disconnect.

Zebra® 105SL™ * Removing and Installing Printhead

Intercom Products RTS TW - unbalanced two wire party line System.

Step-by-step assembly instructions

AnaSonde Assembly. What is the AnaSonde? *Reads temperature, pressure, and humidity data from the atmosphere *After it is sent into the atmosphere, it.

Expand Media Wall & Podium Case Training Video’s & Instructions.

Properly Securing the SCBA in Stowage Bracket Clips 1. Insert SCBA into walk-away bracket clips, ensuring the stowage strap is not trapped within the bracket.

BWST Lecture KIN 436B Spring Transfer Place chair at angle to table Secure Chair Transfer Client Provide assistance as necessary.

MVP-502 MVP-502 Wheelchairs Abound Store To Order Call:

The Training Room, Inc. Presents: Fitting the S.O.M.I. Cervical Collar.

Frame Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team

Engineer Training XL1200 Mechanics. Engineer Training XL1200 Mechanics Confidential 2 The XL1200 is both a Roll to Roll and a Roll to Sheet Printing Machine.

Optical Manufacturing Solutions 1 Probe Assembly.

Lifter Step-by-step assembly instructions (c) 2010 National Fluid Power Association.

Digital StarLab Set-Up, Operation, Maintenance, and Teacher Manual for the Digital StarLab are in the links below or on the training tab in the BlackBoard.

Print Head Removal, Replacement and Alignment. Page 2 CONFIDENTIAL Print Head Assembly Removal  Turn off printer A.C. power  Unplug the printer from.

Step 12 Here is the issue…..the mount for the throttle arm is pushed up against the side of the housing. The problem with this is it allows (due to alignment)

Typical Walk-in Closet with elfa® décor

How to Use the Microphone System It’s as Simple as 0, 1, 2, 3!

Pulleys Vanderbilt Student Volunteers for Science Fall, 2010 Training Refresher.

CricketSat LP (Transmitter) Assembly Instructions This is the instruction slides for the assembly of a transmitter board. This is the board that will fly.

A Division of Health Care Service Corporation, a Mutual Legal Reserve Company, an Independent Licensee of the Blue Cross and Blue Shield Association

Mini Reel Hand Tools. JST Mini Reel Hand Tool JST is proud to introduce the JST Mini Reel hand tool and explain the features, benefits and basic operation.

Pneumatic Arm Assembly Instructions

Hoop Tech Clamp Assembly and Attachment. Contents of package.

Pneumatic Arm Assembly Instructions. Contents of Pneumatic Arm Kit Wooden pieces (⅜” cross-section): 1 X 24”; 1 X 21⅛”; 8 X 7½”; 4 X 7⅛”; 4 X 7”; 2 X.

1 © 3M All Rights Reserved. 3M™Peltor ™ Communications © M Company. All Rights Reserved.

The Mind Body Connection Curriculum FCS Agent Update and Preliminary Evaluation Results May In-Service Training 2012 Lynn Blankenship Nicole Peritore.

© 2008 The McGraw-Hill Companies, Inc. All rights reserved. M I C R O S O F T ® Customizing Themes and Master Slides Lesson 11.

Showing Demonstrations on the TV How to connect the camera to our TV set.

Basic Shooting Skills Positions

Nokia Bluetooth Headset BH-108 for Contact Centers

STELR Solar Car construction notes Based on slides provided by Helen Marussinszky, Mitcham Girls HS, South Australia.

Removing and Replacing the Battery Cover 1. Ensure the phone is turned off. 2. Press the Battery cover locker; lift the battery cover up and away from.

CEVIS handles There are lots of videos on youtube showing how the crew “rides” the CEVIS. The one done by Koichi Wakata is good and shows both operation.

Dr. Wajeeha Mahmood BSPT, PPDPT

University of Wisconsin Medflight Helmet Pat Schenk-Team Leader, Ben Roedl-BWIG, Brett Mulawka-Communications, Richard Long-Asst, Leader, Mike Oldenburg-BSAC.

ASSEMBLING THE PCB – V3.914 Hold the PCB as shown below.

23rd ANNUAL BATTERY CAR RACE FEB. 27,2015 BY: Homer Johnson & Sammy Smith (Ingomar Middle School) (Picture of car here) Car Name: THE ROAD RUNNER.

How to Change Raptor Knife Blades. Step 1: Use a Phillips screwdriver to remove the 5 screws. It is not necessary to remove the lanyard/webbing to change.

15 Minute Workout while at your desk …a healthy workplace initiative.

CBR Radio Training Disaster Preparedness and Management Unit (Version 2.2; 13 April 2015)

CPS MILITARY SOLO SYSTEM DONNING AND ADJUSTING. TLO Given a CPS Military Solo System and combat equipment prepare the CPS Military Solo System for parachuting.

MATTING. REMEMBER… Matt Board is expensive. Measure twice, cut once. Lay your matt board on something clean… on newsprint for example, NOT the floor!

AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.

Prescription Swim Goggle Goggle Parts Adjustable Head Strap Instructions Adjustable Bridge Instructions Rx Instructions Goggle Specs Care and Use Instructions.

Sentek Technologies Joining EnviroSCAN Probes. Probe Components 20-way probe cable connector (special order) Cable spacer (Part No 80015) Probe rods Probe.

VIEW SERIES with Sliding Door

What is TETRIX? If you can dream up a robot design, you can build it with the TETRIX Robotics Design System.

STEP 1: ASSEMBLE ANGLE PLATES

Apache FR Class II Harness

How to Set up Your Computer Workstation

25th Annual 7th and 8th Grade Battery Car Challenge

INSTALLING BYRNE POWER BOX INTO FLEX SYSTEM

Saddle Up! How to Groom and Saddle Your Horse Jessica Shumaker.

The Skeletal System Section 13.2

From: Is Adaptation to Perceived Interocular Differences in Height Explained by Vertical Fusional Eye Movements? Invest. Ophthalmol. Vis. Sci ;54(7):

MODEL: WC SWEEPER SCRUBBER DOCUMENTED BY: Brett Sprietler PAGE NUMBER: 1 DATE: 11/20/ Place (1) HOSE IMPELLER TO TANK ( )

Transportation: Sitting Comfortably

User guide for Direct Observations equipment use

STEP 1: ASSEMBLE ANGLE PLATES

Step-by-step assembly instructions

Step-by-step assembly instructions

The Multifunctional Pneumatic Rehabilitation System

What Shapes Can You See in this Picture?

Getting started Hearing aid processor Ensure the students hearing aids are working. You may need to replace the hearing aid battery. Attach the receivers.

What’s Wrong With This Picture?

Growing Up Fit Together for 2nd grade

Presentation transcript:

1 © 3M All Rights Reserved. Confidential Information for the use of Network Rail 3M™ Peltor™ DECT-Com II Light-Weight Headset (MT701-H03) Fitting Guide

2 © 3M All Rights Reserved. Confidential Information for the use of Network Rail Lightweight Headset  When fitted correctly this is how the MT701- H03 should fit.  The following slides will show a step by step guide to achieving this.

3 © 3M All Rights Reserved. Confidential Information for the use of Network Rail Overview of Fitting Elements Right Ear Adjustment Left Ear Adjustment (with Speaker) Microphone Lapel Clip Neck Ratchet Right Ear Left Ear

4 © 3M All Rights Reserved. Confidential Information for the use of Network Rail Step 1 – Adjust the Right Ear  Carefully bend the metal frame to seat the headset around the right ear as shown in the picture.  Important – this must be adapted to suit the shape of each individuals head.

5 © 3M All Rights Reserved. Confidential Information for the use of Network Rail  Carefully repeat step 1 for the left ear.  Ensure that the speaker remains aligned with the ear canal as pictured.  Important – this must be adapted to suit the shape of each individuals head. Step 2 – Adjust the Left Ear

6 © 3M All Rights Reserved. Confidential Information for the use of Network Rail  The headset features a ratchet adjustment on the rear of the headband as shown in Picture 1.  Holding both sides, push inwards to tighten the headset according to head size and personal comfort.  Important – this must be adapted to suit the shape of each individuals head. Step 3 – Adjust the Neck Ratchet Picture 1 Picture 2

7 © 3M All Rights Reserved. Confidential Information for the use of Network Rail  The headset includes a lapel clip.  Attach the clip as close to the left ear as possible to create a slack in the cable.  Note: The lapel clip can be moved along the cable to facilitate this.  This clip is important as it takes the weight of the headset off the ears and allows greater movement Step 4 – Connect the Lapel Clip

8 © 3M All Rights Reserved. Confidential Information for the use of Network Rail  Whilst holding the headset in place, adjust the flexible boom to ensure that the microphone is positioned in line with the lips.  Once this has been completed the headset should sit on the head as shown in Picture 2. Step 5 – Position the Microphone Picture 1 Picture 2