Front view LED’s pushed into place Buzzer bolted on Fuse holder bolted on.

Slides:

Advertisements

Similar presentations

DS1000B-RM/ DS1500B-RM Battery Replacement Procedure.

Advertisements

CricketSat Assembly.

ES1000C/1500C Battery Replacement Procedure. 1.Pull off the front panel.

MOOD LIGHT PCB ASSEMBLY V By Phil Townshend 2008.

ELECTRONIC CIRCUITS FOR GRADE 9 Prepared by G. C. Accom.

Circuits Energy & Environment. Simple Circuit G -ve +ve Wire Lamp Switch Fuse Battery Power Source Safety Device Controlling Device Purpose Connect circuit.

1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1.

Colorado Space Grant Consortium Timing Circuit HW #4 Class #07 Timing Circuit HW #4 Class #07.

Circuits Series and Parallel. Series Circuits Example: A 6.00 Ω resistor and a 3.00 Ω resistor are connected in series with a 12.0 V battery. Determine.

Current Electricity - Symbols Identify the Symbol.

Circuit Testers and Digital Meters 22 Introduction to Automotive Service James Halderman Darrell Deeter © 2013 Pearson Higher Education, Inc. Pearson Prentice.

FlyBot is an airplane robot. This robot consists of the DC motor which supplies rotatory power to the propeller. Fly.

CIRCUIT SYMBOLS To allow people to document a circuit and everyone to be able to understand it there is a standard set of circuit symbols. These can be.

Procedure of Connecting Coil Unit In series with Capacitor 10 April 14 Product: Fully Automatic Washing Machine.

ELECTRICAL CIRCUITS AND COMPONENT SYMBOLS 1. Some circuit symbols In circuit diagrams components are represented by the following symbols; cellbatteryswitchlamp.

Discovery Kits: Electricity. 1.5 V Battery Batteries in series Closed switch Open switch V Motor Components.

With a knowledge of how to connect cells in parallel and series, we can figure out how to arrange batteries to deliver a desired voltage, and in some cases,

THERMOMETER PROJECT PCB ASSEMBLY INSTRUCTIONS.

ASSEMBLING THE PCB – V3.914 Hold the PCB as shown below.

Automotive Electricity and Electronics, 3/e By James D. Halderman Copyright © 2011, 2009, 2005 Pearson Education, Inc., Upper Saddle River, NJ All.

PS500B/800B Battery Replacement Procedure. 1.Remove the two screws at the bottom of the front panel. 2.Push down then remove the front panel.

PS1500B Battery Replacement Procedure. 1.Pull off the front panel.

ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

Norwood Elementary Science SCHEMATIC DIAGRAM SYMBOLS.

Electricity Circuits. Learning Goals I will be able to identify both series and parallel circuits. I will be able to draw circuit diagrams.

Automotive Electricity and Electronics, 2/e By James D Halderman © 2009 Pearson Education, Inc. Pearson Prentice Hall - Upper Saddle River, NJ Automotive.

ASSEMBLING THE PCB Your PCB has two sides, a COMPONENT side and a TRACK side. The view below shows the component side.

MC inner leg bolts.ppt1 MC Inner Leg Bolts ProE model: stb_added_mc_holes.asm 1/31/07.

Basic Stamp OEM module By Wilmer Arellano. 2  The BASIC Stamp 2 OEM is a discreet component version of the BS2 which may be purchased in kit form. 

ELECTRICAL CIRCUITS. What is an electric current? An electric current is a flow of electrons through wires and components. + - In which direction does.

Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.

Year 8 Fuse Tester Design & Technology PCB Information Fixed value resistors 470R = Yellow, Purple, Brown This component is soldered directly onto the.

SeaPerch Electrical System. Electrical System Overview Assemble the control box. Make the Cat5 connector. Wire the motors to the tether. Wire the control.

SIMPLE/LOW COST ELECTRICITY FOR ELEMENTARY STUDENTS Building Simple Circuits.

ASSEMBLING A CIRCUIT WHILE MAKING A DRAGONFLY. WITH... 2LEDs 2Transistors 1 Resistor 1 Capacitor 1 9V Battery 1 Battery Clip 9 Electric Wire Connectors.

© NTScience.co.uk 2005KS3 Unit 7j - Circuits 1 Circuits.

LED Flashlight.

ELECTRICAL CIRCUITS.

25th Annual 7th and 8th Grade Battery Car Challenge

SeaPerch Electrical System

Electronic Game.

Building a Heater Circuit for a Near-Space Payload

Schematic Diagrams: Electrical Component Symbols

ELECTRICAL CIRCUITS More free powerpoints at

ASSEMBLING THE TIMER Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS.

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

C H A P T E R 20 Electric Circuits

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

Investigating Electricity

How a PNP Transistor Works

Making a simple steady hand game

Electricity: Designing Circuits

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS.

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS More free powerpoints at

BUILDING AN AUTONOMOUS QUADCOPTER.

SeaPerch Electrical System

ELECTRICAL CIRCUITS S.MORRIS 2006

ELECTRICAL CIRCUITS S.MORRIS 2006

Presentation transcript:

Front view LED’s pushed into place Buzzer bolted on Fuse holder bolted on

Fitting it together Here is a front and side view showing how the parts fix into place FRONTSIDE VIEW

Wiring it up 1. Connect the black wire from the buzzer to the tag and the red wire to the fuseholder 2. Connect the red wire from the battery clip to the other end of the fuseholder and the black wire to the tag. 3. Connect the wires to the LED’s as shown. They have to be linked together – in series. 4. Add the resistor and connect it from the spare leg of the LED to the fuseholder connection – the one with the red buzzer lead attached. All you need to do now is add a battery and test your fuse tester!