NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2.

Slides:



Advertisements
Similar presentations
KYMV060C4 2 BY 2 MPDP INSTALLATION GUIDE KINGYOO Electronics., LTD.
Advertisements

Three wheel cargo bike assembly manual
General Information Dimensions · Structure Width: ~ 197in. (16.4’), 99in. (8.2’)/car · Slope Angle: 5 degree · Structure Height (Front): 100in. + base.
Using three IR sensors, SensingBot can sense the front obstacles so it can avoid them. Sensing.
BumperBot uses two contact switches to go through a labyrinth. Bumper.
Hoist Lifting it Right.
Servicing Welch DRYFAST ULTRA Pump Models 2032
Frame Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Installation instructions for the one and only 3 point strut bar for the 5 th gen Accord Please follow the instructions to ensure proper fitment of the.
Tools and Functions R7AxwS3BnU.
Service Training PV Series 42 PVplus
Optical Manufacturing Solutions 1 Probe Assembly.
Honda 450 Installation Manual.
Rev. A Control Number XXXXXXXXXXX Effective Date 10/2/2008 Field Work Instructions for Placard replacement Functional Trainer Page 1/4 Revised Date 10/2/2008.
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
Honda Recon TRX-250 Installation Manual. STEP 1: Remove rear tires and install axle spacers. Use blue thread locker and tighten lugs to ATV specification:
Digital StarLab Set-Up, Operation, Maintenance, and Teacher Manual for the Digital StarLab are in the links below or on the training tab in the BlackBoard.
Presented by: Ginnette Clark Terri Hall Robert Ishmael Michael Petry.
MyLock 644D Service Seminar.
Print Head Removal, Replacement and Alignment. Page 2 CONFIDENTIAL Print Head Assembly Removal  Turn off printer A.C. power  Unplug the printer from.
Robot Quick Build Session Frame Assembly Instructions Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team 1750 Special Thanks to Oklahoma.
Polaris Predator Installation Manual. STEP 1: Remove ATV Rear Tires Remove ATV right side wheel hub Remove ATV stock swing arm (2 bolts) KTRACKS.
TrailerBot is a robot that moves trailer as using connecting device on the back of a truck with only driving space. Learn about standard that divides vehicle’s.
ASSEMBLY INSTRUCTIONS. 2 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: SIDE CUTTING PLIERS PRY BAR 7/16” & 9/16” WRENCH 3/16” ALLEN WRENCH T-15 TORQUE.
RaceBot can do car race using two DC motors. Let's learn how to go forward, backward, right turn, and left turn. with practicing ' ㄱ ' shape racing, and.
Service Seminar Memory Craft Table of Contents MC10001 Top Cover Removal…………………………………………………………………..…………1 Belt Cover Removal……………………………………………………………..……………2-4.
SANUS SYSTEMS THE UNION OF FORM AND FUNCTION Sanus Systems 2221 Hwy 36 West. St. Paul, MN
Installation. Indoor Unit Installation Typical Installation.
EA meeting, Wednesday 6 Dec 2006 TT installation, Jeroen van Tilburg 1 TT installation Installation of the TT station.
FormulaBot is racing car using servo motor as a steering yoke system Formula.
FlyBot is an airplane robot. This robot consists of the DC motor which supplies rotatory power to the propeller. Fly.
MC11000 Kit Replacement 1 1. Open the face plate and remove the 2 screws. Remove and discard the original face plate. 3. Remove the 2 white caps on the.
Jacto Incorporated, 9650 SW Herman Road, Tualatin, Oregon (800)
1 FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS PART NUMBER
USING THE DRIVE-ON HOIST. LOADING VEHICLE ON HOIST 01. Ensure that vehicle is centered left to right. 02. Make sure vehicle is in Park, parking brake.
Control System and Electrical Assembly Produced by Ed Latimer, Team 476 Ken York, Team 476 Ron Markum, Team
Chapter60 Parking Brakes.
Peregrine the Martian Lander Assembly Instructions Mission to Mars 2008.
Scooter ScooterBot is a robot that drives using Servo Motor as steering system.
Framed Canopy Fitting Instructions Contents – 6- Angled frame fixing brackets 1 x handle pack 6 x self drilling tech screws 3 keys 1x door 6 x coach screws.
 Full set of wrenches and sockets  Screw drivers  Tape measure.
Spare Parts List (not to scale)
Service Manual. Cubi Overview The service manual instructs the installing and removing the mSATA, memory card, Wifi card and 2.5 inch HDD.
RICH1 Gas Enclosure Installation. Experimental Area Meeting at CERN on 21st June 2006 Bill Cameron (Imperial College London) on behalf of the RICH1 team.
Six Simple Steps to Fix a Flat
AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.
Assembly of steering.
VIEW SERIES with Sliding Door
What is TETRIX? If you can dream up a robot design, you can build it with the TETRIX Robotics Design System.
STEP 1: ASSEMBLE ANGLE PLATES
Rear end assembly.
Annex 5 - Tower and Lock installation
Annex 4 - Moving Frame and Whiffletree assembly
Easy-Cliner Manual Cable Version Assembly Instruction
Easycliner (Motorized Version) Assembly Instruction
STEP 1: ASSEMBLE ANGLE PLATES
Teacher training resource: Robotic Assembly
T400 Motor Replacement.
Genuine N1. Conversion Installation manual LC
CL4NX +Dispenser (KITTING MANUAL)
Disassembly and Assembly of A07A-W1/W2 Electronic Governor Actuator for AD Fuel Injection Pump
How to Change a Flat Tire
Required tools for installation of a V-1020C Speaker with V-9914M-5 Metal Bridge.
Mounting a BalanceBox®650 to a brick wall
W201 3R hardboard Replacement Procedure.
Required tools for installation of a V-1020C speaker with V-9914 bridge.
Teacher training resource: Robotic Assembly
Activity 1.2.3a Airfoil Construction Guide.
Cable Cap.
Presentation transcript:

NLA-5 Series Rigging Manual

Preparation Material 2

ㄴ Preparation Material Chain block or Electric hoist 2.Shackle (over 5/8 inch) 3.Sling belt 1 2 3

ㄴ Preparation Material FRONT BAR 2.BACK BAR 3.Bolt, Spring washer, Flat washer Bolt & Washer Assembly (Must use 2 washers) 4

ㄴ Preparation Material Short bar is Back bar when connect Frame → NLA-15S NLA-15S → NLA Long bar is Back bar when connect NLA-5 → NLA-5.

ㄴ Preparation Material Shackle (1/2 inch) 1EA 1

ㄴ Preparation Material Electric Screw Driver 2.Hexagonal Tip (5mm) 3.Hexagonal Wrench_Manual (5mm) 1 2 3

Chain block Connection 8

ㄴ Chainblock Connection Like the above picture, connect a sling belt to a truss. (When you install it to H-beam, lower circled 1 to down side.) 1

ㄴ Chainblock Connection Like the picture, assemble the sling belt hanger to the shackle.

ㄴ Chainblock Connection Connected sling belt and shackle

ㄴ Chainblock Connection Connect hanger of chain block(or hoist) to shackle.

ㄴ Chainblock Connection Connected chain block / hoist

Frame Assembly 14

ㄴ Frame Assembly NLA-15S 2.NLA-5 FRAME 2 1

ㄴ Frame Assembly Put NLA-5 FRAME on NLA-15S.

ㄴ Frame Assembly Tighten up and down holes in FRONT BAR with bolts.

ㄴ Frame Assembly Adjust frame to make an alignment of middle hole and the screw hole in the frame.(1) 1

ㄴ Frame Assembly Tighten them with a bolt. (Use an electric screw driver for your convenience)

ㄴ Frame Assembly Connect rear side of the frame using short back bar.

ㄴ Frame Assembly Tighten whole points using manual hexagonal wrench.

ㄴ 프레임 조립 Connected frame on NLA-15S

ㄴ Frame Assembly Install ½ inch shackle to a preferred spot.

ㄴ Frame Assembly Connect the shackle to the hanger of chain block(or hoist).

NLA-5 Assembly 25

ㄴ Speaker Assembly Lift up frame(1) with chain block, and put one NLA-5(2) under the frame. 1 2

ㄴ Speaker Assembly Align front part of the speakers by lowering the frame.

ㄴ Speaker Assembly Firstly, tighten the up and down holes of FRONT BAR with bolts.

ㄴ Speaker Assembly Match middle hole in the bar and the speaker by adjusting position of them.

ㄴ Speaker Assembly Tighten the middle hole with bolts.

ㄴ Speaker Assembly Connect the lower part of short back bar with bolts.

ㄴ Speaker Assembly Lift up the speaker with chain block, and match up hole with speaker’s hole.

ㄴ Speaker Assembly Connect the up hole with a bolt.

ㄴ Speaker Assembly Completed 1 set of NLA-5

ㄴ Speaker Assembly Put another NLA-5 below.

ㄴ Speaker Assembly Align front part of NLA-5 using chain block.

ㄴ Speaker Assembly Connect the up and down hole in the FRONT BAR with bolts.

ㄴ Speaker Assembly Match middle hole in the bar and the speaker by adjusting position of them.

ㄴ Speaker Assembly Tighten the middle hole with bolts.

ㄴ Speaker Assembly Connect the downside of the long back bar with bolts.

ㄴ Speaker Assembly Rear part of NLA Angles for each hole

ㄴ Speaker Assembly You can see that this picture is set to 0 degree

ㄴ Speaker Assembly Choose your preferred angle of hole using chain block. The example in the photo is 0 degree.

ㄴ Speaker Assembly Connect it with a bolt.

ㄴ Speaker Assembly Completed 2 set of NLA-5

ㄴ Speaker Assembly Fully completed figure after repeated process.

NLA-5 RACK Assembly 47

ㄴ Speaker Assembly Insert an amplifier to NLA-5 RACK.

ㄴ Speaker Assembly Fill up spaces with blank panel. 2.Connect power cable, speaker cable, and LAN cable beforehand.

ㄴ Speaker Assembly Put NLA-5 FRAME on NLA-5 Rack.

ㄴ Speaker Assembly Tighten up and down holes in FRONT BAR with bolts.

ㄴ Speaker Assembly Adjust frame to make an alignment of middle hole and the screw hole in the frame.(1) 1

ㄴ Speaker Assembly Tighten them with a bolt. (Use an electric screw driver for your convenience)

ㄴ Speaker Assembly Connect rear side of the frame using short back bar.

ㄴ Speaker Assembly Tighten whole points using manual hexagonal wrench.

ㄴ Speaker Assembly Connected frame on NLA-5 RACK

ㄴ Speaker Assembly Put NLA-15S under NLA-5 RACK.

ㄴ Speaker Assembly Tighten up and down holes in FRONT BAR with bolts.

ㄴ Speaker Assembly Connect the middle with a bolt.

ㄴ Speaker Assembly Connect the lower part of short back bar with bolts.

ㄴ Speaker Assembly Connect the up hole with a bolt.

ㄴ Speaker Assembly Put one NLA-5 below, and tighten the up and down holes of FRONT BAR with bolts.

ㄴ Speaker Assembly Match middle hole in the bar and the speaker by adjusting position of them.

ㄴ Speaker Assembly Tighten the middle hole with bolts.

ㄴ Speaker Assembly Connect the downside of the short back bar with bolts.

ㄴ Speaker Assembly Lift up the speaker with chain block, and match up hole with speaker’s hole.

ㄴ Speaker Assembly Connect the up hole with a bolt.

ㄴ Speaker Assembly Completed 1 set of NLA-5

ㄴ Speaker Assembly Put another NLA-5 below.

ㄴ Speaker Assembly Align front part of NLA-5 using chain block.

ㄴ Speaker Assembly Connect the up and down hole in the FRONT BAR with bolts.

ㄴ Speaker Assembly Match middle hole in the bar and the speaker by adjusting position of them.

ㄴ Speaker Assembly Tighten the middle hole with bolts.

ㄴ Speaker Assembly Connect the downside of the long back bar with bolts.

ㄴ Speaker Assembly Rear part of NLA Angles for each hole

ㄴ Speaker Assembly You can see that this picture is set to 0 degree

ㄴ Speaker Assembly Choose your preferred angle of hole using chain block. The example in the photo is 0 degree.

ㄴ Speaker Assembly Connect it with a bolt.

ㄴ Speaker Assembly Completed 2 set of NLA-5

ㄴ Speaker Assembly Fully completed figure after repeated process.

Caution 81

ㄴ Caution 82 1.You should insert spring washer and flat washer for your bolts. 2.THREE holes in the front part of the speaker must be connected with bolts. (Connecting only 2 holes(up&down) might cause a problem) 3.Position for shackle connecting to the frame is up to user’s preference.

ㄴ Caution 83 4.For tightening bolts, electric screw driver is more convenient and safe than manual hexagonal wrench. 5.When you use electric screw driver, it is recommended to use slow motor speed. (Fast motor speed easily makes a crooked bolt) 6.For your safety and convenience, you have to tighten bolts with manual hexagonal wrench after you use electric screw driver.