Manual de utilizare pentru

Tastatura LCD si Tastatura LCD pentru acces control DGP2-641 and DGP2-641AC Ledul AC: ON = tensiune prezenta OFF = lipsa tensiune alimentare Ledul STATUS : Verde: ON = toate zonele sunt inchise OFF = Zona(e) deschise Flash = Timp de intarziere Rosu: ON = Sistem(e) armate OFF = Sistem(e) dezarmate Flash = Alarma

LCD Keypad and Access Control LCD Keypad DGP2-641 and DGP2-641AC Ecranul LCD va va ghida cu mesaje explicite Foloseste sagetile pentru navigare si selectie [CLEAR] = Sterge data curenta sau revine la pasul anterior [ENTER] = Salveaza data curenta si iese din pasul curent

Armare regulata Armarea regulat armeaza toate zonele din aria selectata(e) 1.Tasteaza [CUDUL DE ACCES]. 3.Daca aveti acces la mai multe arii selectti aria dorita sau apasati [0] petru toate ariile. In cazul cand sunt mai multe arii programate 2.Apasa butonul [ARM]. Armeaza aria daca toate zonele sunt inchise.

Armarea fortata- “Force Arming” Armarea fortata permite armare sistemului cu zone deschise. Zonele se programeaza in prealabil 1.Tasteaza [CODUL DE ACCES]. 3.Daca aveti acces la mai multe arii, selecteaza aria dorita, sau apasti tasta [0] pentru toate ariile. 2.Tasteaza butonul [FORCE]. Armeaza intreaga arie fara a mai astepta sa se inchida zonele declarate force.

Armarea partiala –”Stay Arming” “Stay arming” va arma partial sistemul, - doar zonele nedeclarate “stay” (progrmarea se face in prealabil de programator la cerere) 1.Tastati [CODUL DE ACCES]. 3.Daca aveti acces la mai multe arii, selecteaza aria dorita, sau apasa tasta [0] pentru toate ariile. 2.Tastati butonul [STAY]. Armeaza doar zonele nedeclarate “stay”,

Armarea Instant Cu armarea instant,toate zonele vor genera alarma imediat ce se armeaza sistemul(chiar si zonele definite intarziat) 1.Tastati [CODUL DE ACCES]. 3.Daca aveti acces la mai multe arii, alegeti aria dorita, sau apasati [0] pentru toate ariile. 2.Tastati butonul [5]. Arie armata “stay”, dar alarma se va declansa daca sunt zone deschise (chiar daca sunt definite intarziat)

2.Select the desired area(s). To disarm when entering: 3.Select the desired area(s). Disarming 1.Enter your [ACCES CODE]. To disarm from within the perimeter: 1.Enter your [ACCES CODE]. 2.Press the [DISARM] button.

5.Repeat steps 3 and 4 until all desired zones selected. 4.Press the [BYP] button once the desired zone appears on the screen. Bypass Programming 1.Enter your [ACCES CODE]. 2.Press the [BYP] button. 3.Use the [  ] and [  ] buttons to scroll through the zones. 6.Press [ENTER] to save and exit. When a zone is bypassed, it will be ignored the next time your system is armed.

4.Introdu numarul zonei(din 2 digiti). 3.Tasteaza butonul [1] pentru a seta zona(ele) chime. Programare “Chime” 1.Tasteaza [CODUL DE ACCES]. 5.Tasteaza butonul [ENTER] pentru a salva. 2.Tasteza butonul [9]. Tastatura poate fi programatasa emita un sunet(beep) rapid si intermitent de fiecare data cand zona programta este deschisa. SAU Foloseste butoanele[  ] si [  ]pentru a selecta zona(ele) si apasa butonul [ACC] pentru a activa sau dezactiva functia “chime”. 6.Tasteaza [CLEAR] pentru a iesi.

4.Enter a start time according to the 24hr clock (9:00 p.m. = 21:00). 5.Enter an end time according to the 24hr click (9:00 p.m. = 21:00). Programming a Chime Zone Schedule 3.Press the [2] button to set a chime schedule. Chime zones can also be programmed to chime only when opened between certain hours. 6.Press [CLEAR] to exit. 1.Enter your [ACCES CODE]. 2.Press the [9] button.

Alarm Memory Display “Alarms in Memory [MEM] to View” will appear when an alarm has occurred. 2.Press [CLEAR] to exit. 1.Press the [MEM] button to view the breached zones.

Press and hold the desired one-touch button to access the following: ButtonFeature Table 1: One-touch Buttons One-Touch Buttons [BYP]Bypass programming [ENTER]Regular arm [5]Instant arm [6] Keypad settings [7]View event record display [STAY]Stay arm [FORCE] Force arm [DISARM]Disarm a Stay/Instant Armed area

Panic Buttons Press and hold one of the button combinations listed below to send a panic alarm. Panic Alarm TypeButton Combinations Table 2: Panic Buttons Fire Alarm[7] and [9] Auxiliary Panic (medical)[4] and [6] Emergency Panic (police) [1] and [3]

Programming User Access Codes – Steps 1 to 6 4.Enter the 3-digit User Number to program. 5.Enter a user code (PIN) 1.Enter your [ACCES CODE]. 6.Press the [  ] button. 3.Press [ACC]. 2.Press [0]. Press [  ] to scroll the user codes and then press [ACC]. OR

9.Enter the number of the area you wish to assign. Programming User Access Codes – Steps 7 to 9 8.Press the [  ] button. 7.Press the number(s) of the user option(s) you wish to enable/disable.

Programming User Access Codes – Steps 10 and Enter 2-digit schedule. 10.Enter 2-digit access level. Press the [  ] button to return to user options; press the [  ] button to proceed to step 10; press the [ENTER] button to save and exit.

Programming User Access Codes – Steps 12 to Enter the access control card’s serial number by either using the keypad’s buttons or by presenting the card to the keypad’s reader. 15.Press [ENTER] to save and exit. 13.Press the [  ] button. 12.Press the number(s) of the access control option(s) you wish to enable/disable.

Trouble Display “Trouble(s) [TRBL] to View” will appear when a trouble occurs. To view the trouble display: Use the [  ] and [  ] buttons. Press the [TRBL] button. Press the [NUMBER] of the trouble.

Group [1]: System AC Failure Battery Trouble AUX Current Limit Bell Current Limit Bell Absent ROM Check Error RAM Check Error (DGP-NE96) Trouble Display – Group [1]: System

Group [2]: Communicator TLM1 Fail to Communicate 1 Fail to Communicate 2 Fail to Communicate 3 Fail to Communicate 4 Fail to Communicate PC Trouble Display - Group [2]: Communicator

Group [3]: Modules Module Tamper ROM Check Error TLM Trouble Fail to Communicate Printer Trouble AC Failure Battery Failure Supply Output Trouble Display - Group [3]: Modules

Group [4]: Bus Missing Keypad Missing Module General Failure Bus Overload Bus Comm. Error Group [5]: Zone Tamper Group [6]: Zone Low Battery Group [7]: Zone Fault Group [8]: Clock Loss Trouble Display - Groups [4] to [8]

Thank You