Gas Turbine Power Plant

Slides:



Advertisements
Similar presentations
Engines and Motors Part - 2. Engines and Motors Turbines Rocket Steam.
Advertisements

GAS TURBINE POWER PLANTS
Chapter 7 - Heat Science for X. Agenda Heat Engines External combustion engine Internal combustion engine Petrol engine Diesel engine Efficiency of heat.
Vigyan Ashram, Pabal. In this presentation you will learn : – What is IC engine? – How it works? – Where it is used?
JET PROPULSION Part 3 The Jet Engine.
THERMAL POWER PLANT.
SHIP PROPULSION.
CHAPTER 3 INTERNAL COMBUSTION ENGINES
Combustion Sources. Source: USEPA, APTI, 2012, Combustion Source Evaluation Student Manual.
Steam (Vapour) Power Plant Rankine cycle Power Plant
Section 16.3 Using Heat.
ENERGY CONVERSION ES 832a Eric Savory Lecture 11 – A small-scale power plant worked example Department of Mechanical.
Internal Combustion Engines. Engines External combustion engine Internal combustion engine Steam engine Gas turbine engine Steam engine Gas turbine engine.
Steam Power Plant.
POWER PLANT.
Thermal energy Ch. 6 mostly. Transferring thermal NRG There are three mechanisms by which thermal energy is transported. 1. Convection 2. Conduction 3.
Steam Power Station Presented By Ashvin G. Patel Asst. Prof. (E.E.)
 Industrial societies spend huge amounts of energy.  Much of it is supply by electricity which comes from generators in power stations.
Diesel Engines Found mostly in large trucks, locomotives, farm tractors and occasionally cars. An internal combustion engine Does not mix the fuel and.
Diesel Power Plant Mr.B.Ramesh, M.E.,(Ph.D) By
POWER PLANT TECHNOLOGY INTRODUCTION AND OVERVIEW Prof. Anand Bhatt.
Natural Gas the Cleanest Burning Fossil Fuel.
Introduction of jet engine
Gas Turbine Power Plant
Operation and Maintenance
1. AGV – (Automated Guide Vehicle) Robots that move by following a set path.
STUDY OF BOILER’S ACCESSORIES
Hydro electric (Hydel) Power Plant
Gas Turbine Theory and Construction
November 19, 2013 Agenda 1.Roll 2.PowerPoint titled: Heat Technology 3.Video “Head Rush: Liquid Nitrogen Balloon”
Open Worksheet 4 Transportation Engines Power Point 4
Energy And Environmental Technology
Basic Engine Operation & Construction
Energy and the Environment Spring 2014 Instructor: Xiaodong Chu : Office Tel.: Mobile:
HEAT ENGINE D.A.DEGREE ENGG. & TECHNOLOGY
Gas Turbine Theory and Construction. Introduction Comprehend the thermodynamic processes occurring in a gas turbine Comprehend the basic components of.
CHAPTER 5: Mass and Energy Analysis of Control Volumes
Unit 2 -Gas And Diesel Power Plants
The Diesel Engine The Combustion Cycle The four-stroke combustion cycle of the diesel engine is composed of the intake stroke, compression stroke, power.
11. 2 Steam Energy Energy that comes from the push of steam.
Heat engines played a key role in the development of the modern industrial world. Steam locomotives were an important early use of the steam engine. Electric.
Generating Stations. Bulk electric power is produced by special plants known as generating stations or power plants. Depending upon the form of energy.
Welcome PRESENTATION BY ASHISH MISHRA.
Prof. R. Shanthini Nov 12, An engineering example for unsustainable development.
Lecture 3b: Aircraft Engines s: Propeller + Piston Engines Era  From 1903 (Wright bros.) until the Early 1940s, all aircraft used the piston.
THERMAL POWER PLANT.
What is a Cryocar? It is a liquid nitrogen powered vehicle. Propulsion systems are cryogenic heat engines in which a cryogenic substance is used as a.
Presentation on Steam Power Plants R.C.Chaturvedi
ET375 Applied Thermodynamics 09 Thermodynamic Cycles Introduction to Gas Cycles 12/1/131rm.
Dr. Owen Clarkin School of Mechanical & Manufacturing Engineering Summary of Energy Topics Chapter 1: Thermodynamics / Energy Introduction Chapter 2: Systems.
HEAT-GENERATING EQUIPMENT INTRODUCTION SELECTION EFFICIENCY FURNACES BOILERS CENTRAL HVAC SYSTEMS.
Using Heat Part 1. Science Journal Entry 31 Explain the 2 nd Law of Thermodynamics.
Refrigeration What's Refrigerated? What makes up a system?
Energy from Fossil Fuels Fuel-a substance that provides a form of energy (such as heat, light, electricity or motion) as the result of a chemical change.
Des. Ton Nguyen. MAIN PARTS  Fan  Compressor  Combustor  Turbine  Nozzle.
Limitations Susceptable to lead build up, require use of lead free gasoline. Require “richer” fuel mixture, burn more fossil fuels and emit more CO 2 In.
Content: Introduction A Simple Gas Turbine Plant & It’s Working Plant Layout Types according to Cycle 1. Open Cycle Gas Turbine Plants 2. Close Cycle.
Gas Turbine Power Plant
Prepared by: Kamil Bin Sahidin
Gas Turbine Theory and Construction
BASICS OF MECHANICAL ENGINEERING
PHOTO GALLERY Study Guide in PowerPoint to accompany Thermodynamics: An Engineering Approach, 7th edition by Yunus A. Çengel and Michael A. Boles.
BRAYTON CYCLE AND EFFECT OF INTERCOOLING , REHEAT AND REGENRATION
CACTUS MOON EDUCATION, LLC
Gas Power Plant - Layout and Operation
Jet Engine, How does it work ?
Diesel Automotive Engines
BASIC MECHANICAL ENGINEERING
THERMAL POWER PLANT. A Thermal Power Plant converts the heat energy of coal into electrical energy. Coal is burnt in a boiler which converts water into.
Gas turbines Newer type of internal combustion engine.
Presentation transcript:

Gas Turbine Power Plant 25 April 2017 By Mr.B.Ramesh, M.E.,(Ph.D) Research Scholar, CEG, Anna University, Chennai. Associate Professor of Mechanical Engineering, St. Joseph’s College of Engineering, Jeppiaar Trust, Chennai-119

Unit III – Power plant engineering Gas turbine power plant 25 April 2017 Unit III – Power plant engineering Gas turbine power plant Gas turbine: Working principle : Air is compressed(squeezed) to high pressure by a fan-like device called the compressor. Then fuel and compressed air are mixed in a combustion chamber and ignited. Hot gases are given off, which spin the turbine wheels. Most of the turbine’s power runs the compressor. Part of it drives the generator/machinery. 25 April 2017

Unit III – Power plant engineering Gas turbine power plant… 25 April 2017 Unit III – Power plant engineering Gas turbine power plant… Gas turbine: Description: Gas turbines burn fuels such as oil, nature gas and pulverised(powdered) coal. Instead of using the heat to produce steam, as in steam turbines, gas turbines use the hot gases directly to turn the turbine blades. Gas turbines have three main parts: Air compressor ii) Combustion chamber iii) Turbine 25 April 2017

Unit III – Power plant engineering Gas turbine power plant… 25 April 2017 Unit III – Power plant engineering Gas turbine power plant… Gas turbine: Air compressor: The air compressor and turbine are mounted at either end on a common horizontal axle(shaft), with the combustion chamber between them. Gas turbines are not self starting. A starting motor initially drives the compressor till the first combustion of fuel takes place, later, part of the turbine’s power runs the compressor. The air compressor sucks in air and compresses it, thereby increasing its pressure. 25 April 2017

Unit III – Power plant engineering Gas turbine power plant… 25 April 2017 Unit III – Power plant engineering Gas turbine power plant… Gas turbine: Combustion chamber: In the combustion chamber, the compressed air combines with fuel and the resulting mixture is burnt. The greater the pressure of air, the better the fuel air mixture burns. Modern gas turbines usually use liquid fuel, but they may also use gaseous fuel, natural gas or gas produced artificially by gasification of a solid fuel. Note : The combination of air compressor and combustion chamber is called as gas generator. 25 April 2017

Unit III – Power plant engineering Gas turbine power plant… 25 April 2017 Unit III – Power plant engineering Gas turbine power plant… Gas turbine: Turbine: The burning gases expand rapidly and rush into the turbine, where they cause the turbine wheels to rotate. Hot gases move through a multistage gas turbine. Like in steam turbine, the gas turbine also has fixed(stationary) and moving(rotor) blades. The stationary blades guide the moving gases to the rotor blades and adjust its velocity. The shaft of the turbine is coupled to a generator or machinery to drive it. 25 April 2017

Unit III – Power plant engineering Gas turbine power plant… 25 April 2017 Unit III – Power plant engineering Gas turbine power plant… Applications of gas turbine: Gas turbines are used to drive pumps, compressors and high speed cars. Used in aircraft and ships for their propulsion. They are not suitable for automobiles because of their very high speeds. Power generation(used for peak load and as stand-by unit). Note : Gas turbines run at even higher temperatures than steam turbines, the temperature may be as high as 1100 – 12600C. The thermal efficiency of gas turbine made of metal components do not exceed 36%. Research is underway to use ceramic components at turbine inlet temperature of 13500C or more, and reach thermal efficiencies over 40% in a 300 kW unit. 25 April 2017

Layout of a gas turbine power plant 25 April 2017 Layout of a gas turbine power plant 25 April 2017

Layout of gas turbine power plant… 25 April 2017 Layout of gas turbine power plant… Starting motor: Gas turbines are not self starting. They require a starting motor to first bring the turbine to the minimum speed called coming –in speed, for this purpose a starting motor is required. Low pressure compressor(LPC): The purpose of the compressor is to compress the air. Air from the atmosphere is drawn into the LPC and is compressed. Intercooler: The air after compression in the LPC is hot. It is cooled by the intercooler. The intercooler is circulated with cooling water. 25 April 2017

Layout of gas turbine power plant… 25 April 2017 Layout of gas turbine power plant… High pressure compressor(HPC): The air from the intercooler enters the HPC where it is further compressed to a high pressure. The compressed air passes through a regenerator. Regenerator(Heat exchanger): The air entering the combustion chamber(CC) for combustion must be hot. The heat from the exhaust gases is picked up by the compressed air entering the combustion chamber. Combustion chamber: The fuel(natural gas, pulverized coal, kerosene or gasoline) is injected into the combustion chamber. The fuel gets ignited because of the compressed air. The fuel along with the compressed air is ignited sometimes with a spark plug. 25 April 2017

Layout of gas turbine power plant… 25 April 2017 Layout of gas turbine power plant… High pressure compressor(HPC): The air from the intercooler enters the HPC where it is further compressed to a high pressure. The compressed air passes through a regenerator. Regenerator(Heat exchanger): The air entering the combustion chamber(CC) for combustion must be hot. The heat from the exhaust gases is picked up by the compressed air entering the combustion chamber. Combustion chamber: The fuel(natural gas, pulverized coal, kerosene or gasoline) is injected into the combustion chamber. The fuel gets ignited because of the compressed air. The fuel along with the compressed air is ignited sometimes with a spark plug. 25 April 2017

Layout of gas turbine power plant… 25 April 2017 Layout of gas turbine power plant… High pressure turbine (HPT): In the beginning the starting motor runs the compressor shaft. The hot gases(products of combustion) expands through the high pressure turbine. It is important to note that when the HPT shaft rotates it infact drives the compressor shaft which is coupled to it. Now the HPT runs the compressor and the starting motor is stopped. Note : About 66% of the power developed by the gas turbine power plant is used to run the compressor. Only 34% of the power developed by the plant is used to generate electric power. 25 April 2017

Layout of gas turbine power plant… 25 April 2017 Layout of gas turbine power plant… Low pressure turbine (LPT): The purpose of the LPT is to produce electric power. The shaft of the LPT is directly coupled with the generator for producing electricity. The hot gases(products of combustion) after leaving the HPT is again sent to a combustion chamber where it further undergoes combustion. The exhaust gases after leaving the LPT passes through the regenerator before being exhausted through the chimney into the atmosphere. The heat from the hot gases is used to preheat the air entering the combustion chamber. This preheating of the air improves the efficiency of the combustion chamber. 25 April 2017

Gas turbine power plant… 25 April 2017 Gas turbine power plant… Advantages of gas turbine power plant : Storage of fuel requires less area and handling is easy. The cost of maintenance is less. It is simple in construction. There is no need for boiler, condenser and other accessories as in the case of steam power plants. Cheaper fuel such as kerosene , paraffin, benzene and powdered coal can be used which are cheaper than petrol and diesel. Gas turbine plants can be used in water scarcity areas. Less pollution and less water is required. Disadvantages of gas turbine power plant : 66% of the power developed is used to drive the compressor. Therefore the gas turbine unit has a low thermal efficiency. The running speed of gas turbine is in the range of (40,000 to 100,000 rpm) and the operating temperature is as high as 1100 – 12600C. For this reason special metals and alloys have to be used for the various parts of the turbine. High frequency noise from the compressor is objectionable. 25 April 2017

How a gas turbine engine works Gas turbine working principle 25 April 2017 Videos and Animations How a gas turbine engine works Gas turbine working principle

25 April 2017 Thank You 25 April 2017