Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

Slides:

Advertisements

Similar presentations

Review Problems. Water can be made from hydrogen and oxygen: H 2 (g) + O 2 (g) → H 2 O (g) Some experiments are run in a sealed 1 L flask at 350 K to.

Advertisements

Carbon Deposition in Heterogeneous Catalysis

Simulation lasts 30 years Aquifer is 70% Quartz Specify domain’s starting fluid composition on the Initial pane Initial fluid in equilibrium with Quartz.

Picking up calculation results. After performing a calculation, React can “pick up” the results and use them for a new calculation. You can pick up an.

Ground-Water Flow and Solute Transport for the PHAST Simulator Ken Kipp and David Parkhurst.

Enter your fluid composition on the Basis pane. SpecE8 figures concentrations of aqueous and sorbed species, mineral saturation, and gas fugacity. Go to.

Plot → Map View Switch to map view to enable color maps, color masks, or contour plots.

Introduction to GW contamination and

Subsurface Hydrology Unsaturated Zone Hydrology Groundwater Hydrology (Hydrogeology )

Specify flow rate on the Domain pane. GWB will use Darcy’s law to calculate discharge from the viscosity, permeability, and driving force. You can set.

BIOPLUME II Introduction to Solution Methods and Model Mechanics.

Enter your initial fluid composition on the Basis pane, then go to the Reactants pane to create a reaction path. Choose the type of kinetic reaction.

David Follansbee, John Paccione, Lealon Martin

Clean water Start and end times of two reaction intervals Specify domain’s starting fluid composition on the Initial pane.

CE 548 Introduction to Process Analysis and Selection

X1t models reactive transport in groundwater flows in one linear or radial coordinate. Set initial fluid composition and mass of sorbing mineral Fe(OH)

Contaminant Transport CIVE 7332 Lecture 3. Transport Processes Advection The process by which solutes are transported by the bulk of motion of the flowing.

© 2014 Carl Lund, all rights reserved A First Course on Kinetics and Reaction Engineering Class 12.

Specify chemical composition of fluid and formation minerals from the Initial pane. Set initial temperatureSet starting and ending times.

Specify domain’s starting fluid temperature on the Initial pane Porewater temperature is 40 °C.

Left-drag to detach panes. Transfer your data between GWB apps. Right-click and hold any pane header (Basis, Results, Initial, Inlet, Inject) then drag.

19 Basics of Mass Transport

Initial chemical composition and temperature can vary across the domain. Click on a “+” button to enter heterogeneity data for any field variable: ● enter.

FLOW THROUGH GRANULAR BEDS AND PACKED COLUMN

Porewater temperature is 40°C Specify domain’s starting fluid temperature on the Initial pane.

Multiple Species Chapter 7. Training Manual May 15, 2001 Inventory # Objectives The FLOTRAN multiple species capabilities. Dilute mixture option.

Surface complexation retards Pb ++ transport relative to nonreactive tracer Br −. Use Xtplot to display the concentration of several species along the.

Variable inlet chemistry. Inlet fluid “contaminated” enters the domain from t = 0 to 2 years Inlet fluid “flush” enters the domain from t = 2 to 10 years.

Pulse of Benzene contaminated water is attenuated by biodegradation. X1t models reactive transport in groundwater flows in one linear, radial, or spherical.

Substrate combines with enzyme to form activated complex, which can decay to give catalytic product Michaelis-Menten equation gives rate of forward reaction.

Kinetic reactions React, X1t, and X2t can trace several types of reactions according to kinetic rate laws: Mineral precipitation and dissolution. Redox.

Config→ Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Decouple reaction between carbonate and acetate, carbonate and methane, and sulfate and sulfide. Config → Redox Couples… Default setting: all redox reactions.

Clean water Specify starting fluid composition on the Initial pane.

Specify coordinate system on the Domain pane.

Chain together kinetic reactions

Specify kinetic rate laws for mineral precipitation and dissolution (and other reaction types) on the Reactants pane. Use Arrhenius equation to calculate.

Config → Redox Couples…

Advanced Contaminant-Transport Techniques

Config→ Redox couples…

Contaminant Transport Equations

Set the simulation’s duration

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

Specify domain’s starting fluid composition on the Initial pane

X position (m) I s o t p i c m n C , d a y Bulk fluid CO (aq)

Chain together kinetic reactions

The Intervals pane sets the total duration of the simulation.

The Initial fluid has negligible Pb2+ everywhere but the central node

Set the composition of the initial fluid on the Basis pane.

Specify domain’s starting fluid composition on the Initial pane

Default setting: all redox reactions are coupled.

Concentrations and activities

Transport Modeling in Groundwater

Config → Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Config → Dual Porosity… Run → Go

Set the composition of the initial fluid on the Basis pane.

Config → Redox couples… Decouple redox pairs for electron donating and accepting half reactions.

Chapter Four: Energy transfer by Heat, Work and Mass

Disable redox coupling between As(V) and As(III), Fe(III) and Fe(II)

Choose the type of kinetic reaction

Introduction to the WASP Interface

Swap sorbing mineral into the basis

Transport Modeling in Groundwater

Specify fluid composition and T on the Basis pane

Report limiting factor

Config→ Redox couples…

Equilibrium Constant (Keq)

Presentation transcript:

Decouple reaction between carbonate and Benzene(aq), other forms of carbon. Config → Redox Couples… Default setting: all redox reactions are coupled.

Specify domain’s starting fluid composition on the Initial pane Start and end times of two reaction intervals Decoupled redox pairs (Benzene and carbonate) can be constrained independently.

add → Kinetic → Redox reaction You enable redox kinetics on the Reactants pane.

Type out the redox reaction. Set enzyme function to “on” and enter rate constant, half-saturation constant, and enzyme concentration.

Inlet fluid carries Benzene pulse into the domain Inlet fluid enters the domain from t = 0 to 2 years

Inlet 2 fluid enters the domain from t = 2 to 10 years Clean rinse water: negligible Benzene in the second inlet fluid

Specify domain size, gridding, and flow rate on the Domain pane. Domain is 1 km long, divided into 400 nodal blocks Set specific discharge or head drop Set flowrate for 1st and 2nd reaction intervals

Set various mass transport properties on the Medium pane. Used to calculate coefficient of hydrodynamic dispersion. Porosity affects groundwater velocity. Run → Go traces the model

Initial pulse of Benzene contaminated water is attenuated by biodegradation.