New Product Developments World Leaders in Combustion Management Solutions New Products New Products

New Product Developments World Leaders in Combustion Management Solutions New Products Blowdown Controller & Assembley The Autoflame Blowdown Valve and Module can be used to automate your boiler blowdown process. The blowdown module can be used either with an MM, or as a stand alone unit. Configuration of the blowdown controller is performed either through the MM, or via a USB connection.

New Product Developments World Leaders in Combustion Management Solutions New Products Blowdown Valve Fully stainless steel valve construction PTFE liner to reduce valve wear Ability to replace PTFE liner without removing valve Quick release servo mounting plate DC operated Unic 5 servo motor

New Product Developments World Leaders in Combustion Management Solutions New Products Blowdown Controller Proof of open/close end switches Signal out, indicating valve position Signal in for external control of valve position Backup battery installed to ensure valve closes on power failure Timed operation through M.M. US timed blowdown operation indicates when Blowdown is due Manual Blowdown function through M.M. screens M.M. logging of ‘Blowdown Due’ and ‘Blowdown Completed’ date and time For a quicker and more accurate Blowdown procedure, a park position is used to ensure Blowdown timings are correct. The park position is calculated on valve size Eliminates need for compressed air line

New Product Developments World Leaders in Combustion Management Solutions New Products

New Product Developments World Leaders in Combustion Management Solutions New Products 2 nd Low Cutoff Probe Certified low water cut-off probe New terminals added to the Water Level PCB Can be used with a 3 rd party Water Level system 2 nd low probe operates by means of resistance Switching relays offer a self-check capability on the probe reading. If one of these relays fails, a lockout will occur. Quick connect flying lead

New Product Developments World Leaders in Combustion Management Solutions New Products Mk.7 I/O Module Connections: 16 Line inputs (110V/230V) 8 Volt Free Contacts 6 Analogue Inputs (0-10V, 0-20mA 4-20mA) 6 Analogue Outputs (0-10V,0-20mA 4-20mA)

New Product Developments World Leaders in Combustion Management Solutions New Products

New Product Developments World Leaders in Combustion Management Solutions New Products Mk.7 I/O Module The Mk.7 Input Output (I/O) Modules are a way of incorporating additional equipment into the Autoflame system. The I/O module totalizes input data internally giving it the ability to run as a standalone unit. When paired with the Mk.7 Data Transfer Interface (D.T.I.), detailed logging of the inputs of the Mk.7 I/O Modules takes place. The data gathered by the Autoflame DTI can be collected and viewed using the included CEMS Audit Software, which allows data collection over a local network, or over the internet.

New Product Developments World Leaders in Combustion Management Solutions New Products Mk.7 I/O Module – Main Features Up to 10 I/O Modules can be used on a single Autoflame system. When paired with the Mk.7 D.T.I., the following becomes available: Configurable alarms through Mk.7 D.T.I. touchscreen Analogue inputs are logged over a period of 2 years Analogue and Digital output control through Mk.7 D.T.I. touch- screen, and CEMS Audit Software Averaging of multiple analogue inputs providing a single analogue output

New Product Developments World Leaders in Combustion Management Solutions New Products

New Product Developments World Leaders in Combustion Management Solutions New Products

New Product Developments World Leaders in Combustion Management Solutions New Products Draft Control The Autoflame Draft Control maintains a set stack pressure, which is entered at each point during the commissioning process. By mounting a pressure sensor on the stack, and installing a modulating stack damper, the furnace pressure can be controlled. This is done by using a PI loop and trimming on any chances in the stack pressure. By regulating the stack pressure on a boiler, you can increase the efficiency of heat transfer due to the combustion velocities being slower.

New Product Developments World Leaders in Combustion Management Solutions New Products Draft Control Schematic

New Product Developments World Leaders in Combustion Management Solutions New Products Draft Control – Features and Benefits 7 th channel added to commissioning screens for stack damper Commissioned stack pressures stored in MM’s memory Stainless steel construction of stack damper Utilizes easily replaceable Autoflame Unic10 servomotor Quick connect plug on Stack pressure sensor for easy wiring back to the Water Level PCB Trims using stack damper to maintain commissioned stack pressure PI bands are configurable in the MM’s options and parameters

New Product Developments World Leaders in Combustion Management Solutions New Products Continuous & Pulsed TDS Operation The TDS Probe can be used to regulate a boiler’s TDS values. The control of a boiler’s TDS is essential to ensure that it is operating at its most efficient. The probe measures the TDS either as a timed sample, or as a continuous sample when using an Autoflame TDS valve. The TDS probe requires a Water Level PCB to be fitted to the MM.

New Product Developments World Leaders in Combustion Management Solutions New Products Continuous TDS Operation – Features & Benefits Continuous sampling of TDS values, rather than timed values Increased pressure tolerances Uses Autoflame servomotor Uses Autoflame TDS valve with easily replaceable PTFE liner Switch between pulsed and continuous by changing a single option Uses PI control to maintain configurable target TDS value Updated configuration screens on the Mk.7 MM Updated history screens showing TDS histories on the Mk.7 MM

New Product Developments World Leaders in Combustion Management Solutions New Products Mk.7 Pressure Sensors The Mk.7 pressure sensors now come with a user configurable range. Unlike the previous pressure sensors, that were locked on a single operating range, the Mk.7 sensors have the ability to operate on multiple ranges, as set in Option 1. In addition, these new sensors have a quick connect plug to aid in easy installation and quick replacement. The new sensors have the following features: Quick connect plug for easy installation and replacement Sensors can operate on multiple ranges Full aluminium construction

New Product Developments World Leaders in Combustion Management Solutions New Products Software Updates Mini 7 Modbus 25 Modbus addresses available Communication speeds upgrade for use with the Mk.7 D.T.I. Bootloader ‘Bootloader Updater’ – Updates firmware on units without having to replace the card engine

New Product Developments World Leaders in Combustion Management Solutions New Products Thank you for listening