doc.: IEEE /2215r4 Submission August 2007 Ganesh Venkatesan, Intel CorporationSlide 1 Proposal –Radio Resource Measurement Capability Enabled Bitmask IE Date: Authors:

doc.: IEEE /2215r4 Submission August 2007 Ganesh Venkatesan, Intel CorporationSlide 2 Abstract This document is a submission for Radio Resource Measurement Capability Enabled Bitmask Information Element. Corresponding normative text is in document 07/2285r0. This proposal addresses part of CID #12 (LB96#25-Palm) and SB CID #421:There are too many varied procedures here. It is unlikely that implementations will implement all of the procedures. Each of the supported procedures/reports should be separately indicated and negotiated* * Not Addressed by this submission

doc.: IEEE /2215r4 Submission Rationale k is a collection of measurement tools Some measurements require additional resources and devices may choose not to implement them When a device advertises support for k (dot11RadioMeasurementEnabled is TRUE), it is not clear what RRM –is supported (and enabled) and –what is not supported A STA will have to send one or more measurement requests and analyze the received reports to comprehend what the measuring STA is capable of A simple method is to advertise RRM capability via a RRM Capability Enabled Bitmask IE August 2007 Ganesh Venkatesan, Intel CorporationSlide 3

doc.: IEEE /2215r4 Submission August 2007 Ganesh Venkatesan, Intel CorporationSlide 4 RRM Capability Enabled Bitmask IE Bits in the IE Indicate which of the RRMs are supported by the STA MIB attribute dot11RadioMeasurementEnabled = TRUE means –Capability Information Field:12 is set –that the STA is capable of receiving RRM requests and responding RRM Capability Enabled Bitmask is present in Probe Response, [Re]Association Request and [Re]Association Response if dot11RadioMeasurementEnabled is TRUE Adds 4 octets to the above frames

doc.: IEEE /2215r4 Submission RRM Capability Enabled Bitmask IE (Octet-1) August 2007 Ganesh Venkatesan, Intel CorporationSlide 5 Bit PositionMeasurement Capability EnabledAnnex-A Entry 0Link Measurement2.3, 2.4 1Neighbor Report2.5, 2.6, 12 2Parallel Measurements3.1 3Triggered Reports3.3 4Repeated Measurements3.7 5Measurement Pause3.8 6Quiet Interval 23 7 Beacon Measurement (passive)4.2, 4.6

doc.: IEEE /2215r4 Submission RRM Capability Enabled Bitmask IE (Octet-2) August 2007 Ganesh Venkatesan, Intel CorporationSlide 6 Bit PositionMeasurement Capability EnabledAnnex-A Entry 8Beacon Measurement (active)4.3, 4.6 9Beacon Measurement (table)4.4, Reporting Condition field in Beacon Report Frame Measurement5 12Channel Load6 13Noise Histogram7 14Statistics8 15Location Configuration Information9

doc.: IEEE /2215r4 Submission RRM Capability Enabled Bitmask IE (Octet-3) August 2007 Ganesh Venkatesan, Intel CorporationSlide 7 Bit PositionMeasurement Capability EnabledAnnex-A Entry 16Transmit Stream10 17AP Channel Report11.1, only for APs 18MIB (Annex-Q)18 19Measurement in non-operating channels 20-22Maximum Measurement Duration3.4 Value = 0 indicates that the Measurement Duration specified in the Measurement Request is used. Value = non-zero indicates duration (in Beacon Intervals). Measurement duration = Beacon Interval*2^(Maximum Measurement Duration – 4) 23Reserved

doc.: IEEE /2215r4 Submission August 2007 Ganesh Venkatesan, Intel CorporationSlide 8 RRM Capability Enabled Bitmask IE (Octet-4) Bit PositionMeasurement Capability EnabledNotes/Annex-A Entry 24-26Measurement Pilot Capability ( see next slide) Reserved

doc.: IEEE /2215r4 Submission Measurement Pilot Capability August 2007 Ganesh Venkatesan, Intel CorporationSlide 9 DeviceValueMeaning STA0MP not supported STA1MP supported (AP can transmit and non-AP STA can receive) APOthersMP transmitted by the AP. MP Transmission Interval is derived from the value (next slide). Non-AP STA2MP is used by the non-AP STA Non-AP STAOthersReserved

doc.: IEEE /2215r4 Submission MP Interval from Measurement Pilot Capability August 2007 Ganesh Venkatesan, Intel CorporationSlide 10 Measurement Pilot Capability Value MP Interval with respect to Beacon Interval 2>3% and < 5% of Beacon Interval 3>=5% and < 10% 4>=10% and < 15% 5>=15% and <20% 6>=20% and < 25% 7>=25% and < 50%

doc.: IEEE /2215r4 Submission RRM Capability Enabled Bitmask IE (format) August 2007 Ganesh Venkatesan, Intel CorporationSlide 11 Slide-5Slide-6Slide-7Slide-8 Octet1234 Bit = 1: implies that the device 1.Implements support the corresponding RRM and 2.The corresponding RRM is enabled in the device Exceptions are bits 20-22Support for maximum Measurement Duration 24-26Support for Measurement Pilot

doc.: IEEE /2215r4 Submission Normative Text Changes Minimal change to the amendment: –Define Radio Resource Measurement Capability IE –Add the IE to Probe Response, Association Request and Reassociation Request frames –Fix Clause to describe the semantics of the bits in the RRM Capability Enabled IE: bit set implies that the station will never respond (for the duration of the current association) to the request with a report indicating that it is ‘incapable’ of performing the measurement. A STA receiving a measurement request that it advertises to support in the Capability IE can always respond with a report indicating that it is ‘refusing’ to perform the measurement. –Fix Annex-A –Fix Annex-D August 2007 Ganesh Venkatesan, Intel CorporationSlide 12

doc.: IEEE /2215r4 Submission August 2007 Ganesh Venkatesan, Intel CorporationSlide 13 Feedback?