Backlight Inverter Power Supply Quick Trouble Shooting By Ray Holdren, Service Mgr / Kristel Nevada Instructor / Sencore Adjunct Teacher/ College of Southern.

Slides:

Advertisements

Similar presentations

Kit Building Class Lesson 4Page 1 R and X in Series Inductors and capacitors resist the flow of AC. This property is called reactance. Resistance also.

Advertisements

CHAPTER 3: SPECIAL PURPOSE OP-AMP CIRCUITS

Circuit Analysis and Troubleshooting A Six Step Procedure Created by Jimmie Fouts Houston County Career Academy for.

Landing and Taxi Lights Anti-collision Lights Navigation Lights Cockpit and Cabin Lights Instrument Panel Lights Click on a System Link to Start.

Wien-Bridge Oscillator Circuits. Why Look At the Wien-Bridge? It generates an oscillatory output signal without having any input source.

Problem #2-8 A 480 – 120 V, 60 Hz transformer has its high voltage winding connected to a 460 V system, and its low voltage winding connected to a 24/32.8°Ω.

Department of Information Engineering357 Operation amplifier The tail, large impedance gives high CMRR Mirror as active load. High gain Follower as buffer.

2013 Microwave Service Training All models. Samsung HA Warranty ALL Warranties are subject to change, always verify. 1 Year Parts & Labor Base Warranty,

Department of Information Engineering357 Feedback Op amp golden rules Approximations: 1.Voltage difference between the two inputs is zero 2.Input draws.

California Friendly ® Landscape Training Irrigation System Troubleshooting The Metropolitan Water District of Southern California and the Family of Southern.

PWM (Pulse Width Modulation)

McGraw-Hill © 2008 The McGraw-Hill Companies Inc. All rights reserved. Electronics Principles & Applications Seventh Edition Chapter 15 Regulated Power.

Television 1 Jess UEAB2006 Television Sync Separator.

Pulse Width Modulation (PWM) LED Dimmer Circuit

Chapter 6 Series Circuits. Chapter 6 Series Circuits.

Amplifier Circuit This amplifier circuit DC analysis.

Lab #5 Overview Activity #1 - Simulation of an Op-Amp inverting amplifier Activity #2 - Build and Test the Op-Amp inverting amplifier Activity #3 - Determining.

Ch4 Electronic Components Circuit/Schematic Symbols.

1 Applied Control Systems Technology. 2 Pin configuration Applied Control Systems.

1. What type of voltage is supplied by a rectifier?

MAE156A October 12, 2006 UCSD H. Ali Razavi.  Electric voltage is similar to height difference: - Electrons start moving under voltage difference - Unless.

NPN Foundations of Technology NPN © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™ Foundations.

CHAPTER 11 Op-Amp Applications. Objectives Describe and Analyze: Audio mixers Integrators Differentiators Peak detectors Comparators Other applications.

Microprocessor Interface

CHAPTER 4 The Bipolar Transistor. OBJECTIVES Describe and Analyze: Transistor architecture Transistor characteristics Transistors as switches Transistor.

Electronic Devices and Circuit Theory

1 Basic Electrical Series and Parallel Circuits. 2 Introduction So far we have looked at circuits that have one path for electricity to go as well as.

Electronic Components Circuit/Schematic Symbols. RESISTOR Resistors restrict the flow of electric current, for example a resistor is placed in series.

LOGIC GATES. Electronic digital circuits are also called logic circuits because with the proper input, they establish logical manipulation paths. Each.

Module 2: Series DC Circuits. RecapRecap Do you still recall these?

Electronic Parts.

Principles & Applications

The Transistor Switch.  Computers work with Boolean algebra – two logic states – TRUE or FALSE  These states can be easily represented electronically.

How an NPN Transistor Works

Applications of OP-AMP. Introduction Operational amplifier using IC's is inexpensive, versatile and easy to use. For this reason they are used not only.

Inverter power supply symptoms can be typically broken down into the following categories: 1. All Outputs Normal: 2. All Outputs Dead (no output): 3.

UNIVERSAL HORIZONTAL ANALYZER (HA2500) TRAINING. HA2500 Universal Horizontal Analyzer.

MALVINO Electronic PRINCIPLES SIXTH EDITION.

Siemens Review – Chapters 2 and 3 Potentiometers.

(Transformer Coupling)

Field Replaceable Units, Common Problems, and Flowcharts.

ELECTRONICS – Input Transducers Engineering Science – National 5.

Amateur Radio Licensure Week 5: Advanced Electronics Seth Price, N3MRA New Mexico Institute of Mining and Technology February 28, 2016.

Troubleshooting of PA system

Chapter 2 Diode Applications. Objectives  Explain and analyze the operation of both half and full wave rectifiers  Explain and analyze filters and regulators.

A Requirement for Superposition. Objective of Lecture Introduce the property of linearity Chapter 4.2.

Chapter 5 BJT AC Analysis.

Chapter 8: FET Amplifiers

DR. S. & S. S. GANDHY COLLEGE OF ENGINEERING AND TECHNOLOGY

OVER VOLTAGE OR UNDER VOLTAGE

M220 repair trouble shooting for L 陳福

LOAD CUTOFF SWITCH UPON OVER VOLTAGE OR UNDER VOLTAGE

Feedback No feedback : Open loop (used in comparators)

Electronic Components

FET Amplifiers.

Examples of Negative Feedback Applications: A) Inverting Amplifiers

What is an Op-Amp Low cost integrating circuit consisting of:

AC Inlet & AC Input Filter

6.0 Voltage Regulators.

Principles & Applications

Analog Electronic Circuits 1

Wien-Bridge Oscillator Circuits

Circuit Analysis and Troubleshooting

Transformer Impedance

Chapter 8: FET Amplifiers

Chapter 5 OUTLINE Op-Amp from 2-Port Blocks

22 Chapter Basic Electrical Tests. 22 Chapter Basic Electrical Tests.

Presentation transcript:

Backlight Inverter Power Supply Quick Trouble Shooting By Ray Holdren, Service Mgr / Kristel Nevada Instructor / Sencore Adjunct Teacher/ College of Southern Nevada, Cheyenne Campus

Quick Inverter Troubleshooting 1. First Check V-In Voltage and then check on the other side of the Fuse to Verify that there’s voltage to the Inverter. 2. Test Switched – In or Enable Voltage. Make certain that the Microprocessor has turned on the device. If not, then recheck the Micro Processor or Cables for Defects or missing signals. 3. Test the Switched Input Voltage and verify the Switching Device is working. 4. Test the Oscillator on the Control IC. Verify that the Chip is working. If it’s working, go to step 6. If not, go to step Test the Latch Voltage to see if the IC is in a Latched Out Condition. This can happen for two reasons: (1.) There is only One side of the inverter working. (2.) The Inverter is in a Short Circuit Shut Down Condition. 6. If the Oscillator is OK, Test the Driver Transistors to see if they have an Input from the IC.Then Check their Outputs. If there are no Inputs, the IC is Bad. If there are no outputs, change the Driver Transistors. If there are Outputs, go to step 7.

7. Check the Outputs of the Oscillator Amplifier Transistors. If there’s no Output, the Amplifier Transistors should be replaced. If they’re OK, go to step 8 (note: Change Both Transistors if one is found Bad) 8. Test the Transformers Primary & Secondary for Open or Shorted Windings. Replace if Necessary 9. If the Transformer’s are Good, Test the Output Capacitors and Replace any defective ones you find. 10. Next, Test the Cold Cathode Fluorescent Lamps (CCFL’s). Substitute the lamps with a Load Resistor(s) (equal to the impedance of the lamps) to verify that the Inverter is working properly. Then you can test the Lamps with a known good inverter to Verify if they’re working or not. You must use an Inverter, you can not test them with a Meter. Replace any Defective CCFL’s that maybe Shorted or Burned Out. 11. The last step would be to Burn-Test the Inverter and the Lamps to make sure your repairs are correct. Only Burn-Test while you are present. In case there are any Danger of Shock Hazards that might happen. Quick Inverter Troubleshooting