Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar IC technology:

Slides:

Advertisements

Similar presentations

Operational Amplifier

Advertisements

Chapter 5: BJT AC Analysis. Copyright ©2009 by Pearson Education, Inc. Upper Saddle River, New Jersey All rights reserved. Electronic Devices and.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar transistors 3.

Differential Amplifiers and Integrated Circuit (IC) Amplifiers

Chapter 7 Operational-Amplifier and its Applications

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar transistors 2.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar transistors 1.

Transistors and transistor circuits

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Field effect transistors.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar IC transistor.

Recall Last Lecture DC Analysis and Load Line

APPENDIX B SPICE DEVICE MODELS AND DESIGN SIMULATION EXAMPLES USING PSPICE AND MULTISIM Microelectronic Circuits, Sixth Edition Sedra/Smith.

Chapter 5 Bipolar Junction Transistors

Presentation On BIPOLAR JUNCTION TRANSISTOR

Electronic Devices Prepared by Kazi Md. Shahiduzzaman Transistor.

Department of EECS University of California, Berkeley EECS 105 Fall 2003, Lecture 15 Lecture 15: Small Signal Modeling Prof. Niknejad.

Output Stages and Power Amplifiers

For the exclusive use of adopters of the book Introduction to Microelectronic Fabrication, Second Edition by Richard C. Jaeger. ISBN © 2002.

Department of Information Engineering286 Transistor 3-layers device –npn (more common) –pnp (less common) N P N e b c P N P e b c.

Radio Frequency Amplifiers In this section of the course: Why do common emitter amplifiers often have a disappointingly low upper cut-off frequency ? Where.

Department of EECS University of California, Berkeley EECS 105 Fall 2003, Lecture 14 Lecture 14: Bipolar Junction Transistors Prof. Niknejad.

BASIC ELECTRONICS.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Operation of PN junctions:

Storey: Electrical & Electronic Systems © Pearson Education Limited 2004 OHT 21.1 Bipolar Transistors  Introduction  An Overview of Bipolar Transistors.

Semiconductor Devices III Physics 355. Transistors in CPUs Moore’s Law (1965): the number of components in an integrated circuit will double every year;

1 LW 6 Week 6 February 26, 2015 UCONN ECE 4211 F. Jain Review of BJT parameters and Circuit Model HBT BJT Design February 26, 2015 LW5-2 PowerPoint two.

Introduction to Transistors

ENE 311 Lecture 10.

Module 2 Bipolar Junction Transistor. Learning Outcomes 1.The 3 terminals or regions of a BJT. 2.Construction and symbol of NPN and PNP types 3.Low power.

Chapter 6. Bipolar Junction Transistors (BJTs). Bipolar Junction Transistor Three terminal device Voltage between two terminals to control current flow.

SEMICONDUCTOR DEVICES. Diodes as a semiconductor devices Symbol and Structure Diodes is made by joining p-types and n- types semiconductor materials.

Microelectronic Circuit Design McGraw-Hill Chapter 5 Bipolar Junction Transistors Microelectronic Circuit Design Richard C. Jaeger Travis N. Blalock Chap.

Bipolar Junction Transistors (BJTs) The bipolar junction transistor is a semiconductor device constructed with three doped regions. These regions essentially.

BJTs. Transistor The transistor is the main building block “element” of electronics. A transistor is a semiconductor device used to amplify and switch.

Electronic Devices and Circuit Theory

3-1 McGraw-Hill Copyright © 2001 by the McGraw-Hill Companies, Inc. All rights reserved. Chapter Three The Bipolar Junction Transistor.

Large Part Of This Lecture is Taken From Manipal Institute India

Chapter 5 Bipolar Junction Transistors

Electronic Principles 7th Edition Albert Malvino & David J Bates

Introduction to BJT Amplifier BJT (Review). Still remember about BJT? The emitter current (i E ) is the sum of the collector current (i C ) and the base.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Field effect transistors.

Budapest University of Technology and Economics Department of Electron Devices Solution of the 1 st mid-term test 20 October 2009.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Operation of PN junctions:

Transistor (BJT). Introduction BJT (Bipolar Junction Transistor) Vaccum tubes It comes because it is most advantageous in amplification Why it is called.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course MOS inverters

 A transistor: a three-terminal semiconductor device that can perform two functions: amplification and switching.  Amplification consists of magnifying.

Lab Experiment: 3 Objectives: To understand the Transistor’s characteristics. Construct the Transistor circuit ( Common base and common emitter connection.

Control questions (physics basics, pn-junction) What does “direct bandgap” and “indirect bandgap” semiconductor mean? What is the Fermi-level? How does.

BJT Bipolar Junction Transistors (BJT) Presented by D.Satishkumar Asst. Professor, Electrical & Electronics Engineering

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar IC technology:

CSE251 Lecture 8: Introduction to Bipolar Junction Transistor (BJT)

COURSE NAME: SEMICONDUCTORS Course Code: PHYS 473 Week No. 5.

COURSE NAME: SEMICONDUCTORS Course Code: PHYS 473 Week No. 8.

PEN NO Ahir Darshan Harsora Ashish Mistry Ravi.

Regions of a Transistor A Bipolar Junction Transistor is a three terminal device containing 3 regions: Emitter, Base and Collector.

Introduction to BJT Amplifier Bipolar Junction Transistor (Review)

Bipolar Junction Transistors (BJTs)

Introduction to BJT Amplifier

Chapter 5: BJT AC Analysis

Analog Electronic Circuits 1

CMOS Devices PN junctions and diodes NMOS and PMOS transistors

ترانزیستور BJT دکتر سعید شیری فصل پنجم از:

Transistor Characteristics

Bipolar Processes Description

J.-B. Seo, S. Srirangarajan, S.-D. Roy, and S. Janardhanan

Microelectronics, BSc course

BIPOLAR JUNCTION TRANSISTOR (BJT)

Bipolar Junction Transistors Md. Rabiul Islam Dept. of Biomedical Engineering 8/3/

Presentation transcript:

Budapest University of Technology and Economics Department of Electron Devices Microelectronics, BSc course Bipolar IC technology: set of elements

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Set of components available in bipolar IC-s ► Resistor with base diffusion ► Resistor + emitter diffusion ► PNP transistors ► Thin film capacitance ► Layout of an OpAmp

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set available in bipolar IC processes

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Detail of a bipolar IC – as seen by a scanning electron microscope

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s npn (vertical) transistor Island (well) Substrate Buried layer Emitter Base

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s the isolation diffusion

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Structure of an npn IC transistor Island (well) Substrate Buried layer Emitter Base metal

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s npn transistors Effective emitter edge at the base contact side (I=2 A/cm), EB br.down: 5-6 V, CB br.down V, f T = MHz Process optimized for the npn (vertical) transistors

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s High current npn transistors

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Area efficient solutions: two transistors in a common isolation well, multi-emitter transistor Element set in bipolar IC-s Different npn transistors

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Different npn transistors Effective emitter edge at the base contact side (I=2 A/cm)

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Resistor with base diffusion island (well)

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Resistor with base diffusion There could be multiple resistors in the same isolation well The well must be connected to +U CC !

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Resistor with base diffusion, folded as a meander Accuracy, parasistics

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET How to make components VERY MUCH identical? same layout shape same position close to eachother larger than minimal size same temperature

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Resistor with base diffusion, cross section reduced by emitter diffusion

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s value: few times 100 k  emitter diffusion base diffusion Slightly nonlinear Limited voltage range Resistor with base diffusion, cross section reduced by emitter diffusion

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET small emitter diffusion resistor (connection underpass), value cca. 2  Emitter diffusion Metallization Element set in bipolar IC-s

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Lateral pnp transistor

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Multiple transistors in common well Element set in bipolar IC-s Lateral pnp transistor

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Forms a current mirror Element set in bipolar IC-s Lateral pnp "sector" transistors overlapping contact window

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET I I I 3I Also with circular shape! Element set in bipolar IC-s Lateral pnp "sector" transistors

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET n + no buried layer push and pull amplifier (B) Element set in bipolar IC-s Vertical pnp transistor vertical pnp structure

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET d ox : 0,1  m (50 V) C spec : 3-400pF/mm 2 Element set in bipolar IC-s The thin film capacitor Metal

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s Thin film (metal-SiO 2 -n + ) capacitor in an OpAmp Value: cca. 30pF C spec : 3-400pF/mm 2

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Compare the size of the capacitor and the transistors! Element set in bipolar IC-s Thin film (metal-SiO 2 -n + ) capacitor in an OpAmp

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Element set in bipolar IC-s The pn junction as a capacitor The space charge capacitance can be utilized, but voltage dependent (non-linear) may not be forward biased! EB: 1000pF/mm 2 (up to 5 V) CB: 150pF/mm 2 (up to ~50 V)

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET OpAmp layout, component arrangement T1, T2: NPN, input differential pair T3, T4: PNP, lateral T5, T6, T7: NPN T10, T11, T13: PNP lateral transistors D1, D2: diodes T16-17: NPN darlington T19-21: 3 NPN transistors in a common well R1, R6: large resistors R7: base+emitter diff. resistor R8, R9: small resistors T22: PNP vertical T23: NPN vertical (high current) Symmetry – to assure same thermal feedback path. This layout is not yet the best.

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Thermal effects in analog IC-s: a bipolar OpAmp ► Thermal impedances ► Thermal feedback in case of an OpAmp ► How does the layout influence the thermal feedback ► Layout – thermally optimized

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET The thermal impedances The transfer impedance Z th complex valued The self impedance T 1 temperature rise

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Thermal feedback – in an OpAmp Stationary state, V OUT > 0   -2 mV/ o C

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Thermal feedback – in an OpAmp Stationary state Effect on the open loop characteristic

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Thermal feedback – in an OpAmp Methods for analysis Both measurements and simulations were done. A well known, commercially available circuit was studied (  A741 OpAmp). Both stationary state and dynamic behaviour. Identical type from different IC venors: different layout designs realizing the same electrical schematic. Actual layout (component arrangement) was identified by "reverse engineering".

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Details of the model Schematic of the OpAmp Physical layer structure Device under test:  A741 OpAmp Yellow transistors considered by electro-thermal model

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Reverse engineered layouts Layout "A"

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Reverse engineered layouts Layout "B"

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Open loop characteristics (measurement and simulation) Layout "A"

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Layout "B" Open loop characteristics (measurement and simulation)

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Thermal effects in the output impedance Frequency domain analysis

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET Layout "A", upper transistor on, G=10 4 Effect appears even if there is no load! Frequency domain analysis

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET "A" "B" Difference only in layout! Frequency domain analysis

Budapest University of Technology and Economics Department of Electron Devices Microelectronics BSc course, Element set in bipolar IC-s © András Poppe & Vladimír Székely, BME-EET "A" "B" Input differential pair (common centroid) Output transistors The ideal layout