University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 1 Chunsheng Li Department of Mechanical & Industrial Engineering.

Slides:



Advertisements
Similar presentations
As close to chemistry as we can get
Advertisements

ENGINE HEAT TRANSFER P M V Subbarao Professor Mechanical Engineering Department Loss of Heat is encouraged only to keep engine safe…. It’s a penalty on.
Lecture 15: Capillary motion
Heat Transfer with Change of Phase in Continuous Casting Ernesto Gutierrez-Miravete Rensselaer at Hartford ANSYS Users Group Meeting September 28, 2010.
Ss Hefei, China July 19, 2011 Nuclear, Plasma, and Radiological Engineering Center for Plasma-Material Interactions Contact: Flowing.
Lesson 17 HEAT GENERATION
Optimization of Laser Deposited Rapid Tooling D. Schwam and Y. Wang Case Western Reserve University NADCA DMC, Chicago – Feb.17,
Combined thermal, solutal and momentum transport. Assume a rigid mold. Imperfect contact and air gap formation at metal/mold interface Design of mold surface.
Thermoforming Process
UNIT 13 : HEAT 13.1 Thermal Conductivity 13.2 Thermal Expansion.
Temperature, Heat, and the First Law of Thermodynamics
University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Ya Meng 1 Modeling Interfacial Flux Layer Phenomena in the Shell/Mold Gap Using.
MECHANISM OF HEAT TRANSFER Mode of Heat transfer Conduction Convection
Chapter 2: Overall Heat Transfer Coefficient
Chapter 2: Steady-State One-Dimensional Heat Conduction
Analysis of Simple Cases in Heat Transfer P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Gaining Experience !!!
Japan-US Workshop held at San Diego on April 6-7, 2002 How can we keep structural integrity of the first wall having micro cracks? R. Kurihara JAERI-Naka.
Glass 1 Radiative Heat transfer and Applications for Glass Production Processes Axel Klar and Norbert Siedow Department of Mathematics, TU Kaiserslautern.
Thermo-fluid Analysis of Helium cooling solutions for the HCCB TBM Presented By: Manmeet Narula Alice Ying, Manmeet Narula, Ryan Hunt and M. Abdou ITER.
CHE/ME 109 Heat Transfer in Electronics
1 Deformation and damage of lead free materials and joints J. Cugnoni*, A. Mellal*, Th. J. J. Botsis* * LMAF / EPFL EMPA Switzerland.
Thermal Development of Internal Flows P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Concept for Precise Design ……
Mechanical characterization of lead- free solder joints J. Cugnoni*, A. Mellal*, Th. J. Pr. J. Botsis* * LMAF / EPFL EMPA Switzerland.
1 MODELING DT VAPORIZATION AND MELTING IN A DIRECT DRIVE TARGET B. R. Christensen, A. R. Raffray, and M. S. Tillack Mechanical and Aerospace Engineering.
M. Yoda, S. I. Abdel-Khalik, D. L. Sadowski and M. D. Hageman Woodruff School of Mechanical Engineering Extrapolating Experimental Results for Model Divertor.
1-D Steady Conduction: Plane Wall
Uncertainty Quantification and Dimension Prediction in Forging and Cooling Processes Belur K. Badrinarayan Adviser: Dr. Ramana V. Grandhi.
Heat Transfer Rates Conduction: Fourier’s Law
Wittaya Julklang, Boris Golman School of Chemical Engineering Suranaree University of Technology STUDY OF HEAT AND MASS TRANSFER DURING FALLING RATE PERIOD.
Deduction of Fundamental Laws for Heat Exchangers P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Modification of Basic Laws for.
University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Claudio Ojeda 1 TAPER PREDICTION IN SLAB AND THIN SLAB CASTING MOLDS Claudio.
Fouling Factor: After a period of operation the heat transfer surfaces for a heat exchanger become coated with various deposits present in flow systems,
1 Recent Progress in Helium-Cooled Ceramic Breeder (HCCB) Blanket Module R&D and Design Analysis Ying, Alice With contributions from M. Narula, H. Zhang,
ME 520 Fundamentals of Finite Element Analysis
1 Calorimeter Thermal Analysis with Increased Heat Loads September 28, 2009.
Heat Transfer Equations For “thin walled” tubes, A i = A o.
Calorimeter Analysis Tasks, July 2014 Revision B January 22, 2015.
LASER and TIG welding ANSYS FE model for thermal and mechanical simulation (A. Capriccioli)
PAT328, Section 3, March 2001MAR120, Lecture 4, March 2001S16-1MAR120, Section 16, December 2001 SECTION 16 HEAT TRANSFER ANALYSIS.
CTC / MTC 322 Strength of Materials
University of Illinois at Urbana-Champaign Computational Fluid Dynamics Lab Bin Zhao 1 LES Simulation of Transient Fluid Flow and Heat Transfer in Continuous.
One-Dimensional Steady-State Conduction
States of matter Solid: Liquid Gas Plasma Fluid: Crystalline Amorphous.
Silesian University of Technology in Gliwice Inverse approach for identification of the shrinkage gap thermal resistance in continuous casting of metals.
Heat Transfer Equations. Fouling Layers of dirt, particles, biological growth, etc. effect resistance to heat transfer We cannot predict fouling factors.
Phase Change Analysis Chapter 9. Training Manual Inventory # March 15, Chapter Overview Phase Change –Terminology –Theory –Material Properties.
MECH4450 Introduction to Finite Element Methods
Heat Transfer Equations For “thin walled” tubes, A i = A o.
Chapter 3 Part 2 One-Dimensional, Steady-State Conduction.
External Flow: The Flat Plate in Parallel Flow Chapter 7 Section 7.1 through 7.3.
Heat Transfer by Convection
Heat Transfer Su Yongkang School of Mechanical Engineering # 1 HEAT TRANSFER CHAPTER 8 Internal flow.
Winter/ IntroductionM. Shapiro 1 Can calculate Q 12 [J] from the first law of thermo. קצב מעבר חום heat transfer rate can’t calculate from thermo.
CONVECTION : An Activity at Solid Boundary P M V Subbarao Associate Professor Mechanical Engineering Department IIT Delhi Identify and Compute Gradients.
TS Cool Down Studies TSu Unit Coils (24-25) N. Dhanaraj and E. Voirin Tuesday, 10 March 2015 Reference: Docdb No:
HEAT TRANSFER Problems with FEM solution
TEMPERATURE & ZEROTH LAW OF THERMODYNAMICS Heat – transfer of energy due to temperature differences ● Heat flows - objects do not have heat ● Heat flows.
Beijing Institute of Technology
One Dimensional Steady State Heat Conduction
Thermal-Structural Finite Element Analysis of CLIC module T0#2
Thermoforming Process
UNIT - 4 HEAT TRANSFER.
Thermal analysis Friction brakes are required to transform large amounts of kinetic energy into heat over very short time periods and in the process they.
MODEL INVESTIGATION OF MOLD LEVEL MONITORING WITH THERMOCOUPLES
Fundamentals of Heat Transfer
ANSYS FE model for thermal and mechanical simulation
Chapter 7: Thermal Properties of Matter
What is Fin? Fin is an extended surface, added onto a surface of a structure to enhance the rate of heat transfer from the structure. Example: The fins.
A. Vertkov et al., SC “Red Star”, Moscow, Russia
Fundamentals of Heat Transfer
Presentation transcript:

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 1 Chunsheng Li Department of Mechanical & Industrial Engineering University of Illinois at Urbana-Champaign October 15, 2002 Chunsheng Li Department of Mechanical & Industrial Engineering University of Illinois at Urbana-Champaign October 15, 2002 Investigation of ideal taper in billet molds to avoid in-mold and sub-mold cracks using 2D FEM thermal stress model

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 2 Objective Investigate the optimal mold wall profile to avoid in-mold or sub-mold cracks for billet casters without sub-mold support. Predict the ideal taper profiles for billet casters as a function of casting speed, heat flux, mold distortion, and mold length using slice domain simulation. Study the corner effects to the ideal taper profiles predicted by slice domain simulation. Investigate the optimal mold wall profile to avoid in-mold or sub-mold cracks for billet casters without sub-mold support. Predict the ideal taper profiles for billet casters as a function of casting speed, heat flux, mold distortion, and mold length using slice domain simulation. Study the corner effects to the ideal taper profiles predicted by slice domain simulation.

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 3 Model Descriptions Finite element thermal stress model Phase fractions from non-equilibrium Fe-C phase diagram for plain carbon steel Recalescence and kinetics neglected Efficient contact algorithm to simulate the interaction between mold wall and shell surface. Fully coupled thermal-stress simulation to capture the thermal and mechanical behavior of the interfacial layer in reality. 2-D generalized plane strain Finite element thermal stress model Phase fractions from non-equilibrium Fe-C phase diagram for plain carbon steel Recalescence and kinetics neglected Efficient contact algorithm to simulate the interaction between mold wall and shell surface. Fully coupled thermal-stress simulation to capture the thermal and mechanical behavior of the interfacial layer in reality. 2-D generalized plane strain

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 4 Heat Transfer Model Validation Lines: Boley & Weiner’s analytical solution* Symbols: CON2D computation results * J. H. Weiner and B. A. Boley, J. Mech. Phys. Solids, 1963, Vol. 11, pp

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 5 Stress Model Validation Lines: Boley & Weiner’s analytical solution* Symbols: CON2D computation results * J. H. Weiner and B. A. Boley, J. Mech. Phys. Solids, 1963, Vol. 11, pp

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 6 Steel Properties Assumed Mizukami elastic modulus data Temperature dependent conductivity, enthalpy and thermal linear expansion. Super creep model for liquid elements to treat them as solid without generating unphysical stress in liquid. Kozlowski constitutional equations for austenite, and modified model for delta-ferrite: –Kozlowski Model for Austenite –Modified Power Law Model for  -ferrite Mizukami elastic modulus data Temperature dependent conductivity, enthalpy and thermal linear expansion. Super creep model for liquid elements to treat them as solid without generating unphysical stress in liquid. Kozlowski constitutional equations for austenite, and modified model for delta-ferrite: –Kozlowski Model for Austenite –Modified Power Law Model for  -ferrite

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 7 Constitutive Model

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 8 Non-equilibrium phase diagram* of plain carbon steels ** used in CON2D *Young Mok WON et. al., Effect of Cooling Rate on ZST, LIT, ZDT of Carbon Steels Near Melting Point”, ISIJ International, Vol. 38, 1998, No. 10, pp –1099 **Other Steel Components: 1.52%Mn, 0.34%Si, 0.015%S, 0.012%P *Young Mok WON et. al., Effect of Cooling Rate on ZST, LIT, ZDT of Carbon Steels Near Melting Point”, ISIJ International, Vol. 38, 1998, No. 10, pp –1099 **Other Steel Components: 1.52%Mn, 0.34%Si, 0.015%S, 0.012%P

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 9 Properties Enthalpy TLE Conductivity

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 10 Mold Heat Flux

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 11 Mold Heat Flux Data Instantaneous Heat Flux (MW/m 2 ) Averaged Heat Flux (MW/m 2 ) Wolf Eqn for Slag Casting 7.3t(s) -0.5 Wolf Eqn for Oil Casting 9.5t(s) -0.5 Brimacombe t(s) 0.5 C. Li Eqn for Slab Casting 4.05t(s) C. Li Lower Q Eqn for Billet t(s), t< t(s) , t>= t(s) t(s) -1 C. Li higher Q Eqn for Billet 6.5(t(s)+1) t(s) -1 ((t(s)+1) ) Lorento1.4V c (m/min) 0.5

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 12 Instantaneous Heat Flux Assumed *Instantaneous data is from: I.V. Samarasekera et. al., “High Speed Casting of High Quality Billets”, Strategic Project Report, Sep. 1998

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 13 Spray Water Heat Convection Coefficient Assumed Coefficient calculated from Nozaki Model:

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 14 Interfacial Layer Heat Transfer Model Where: h water :heat transfer coefficient between mold cold face and cooling water t mold :mold wall thickness k mold :mold wall heat conductivity t gap :gap between mold hot face and shell surface k gap :gap heat conductivity r contact :contact heat resistance between mold wall and shell surface h rad :heat radiation coefficient between mold hot face and shell surface Where: h water :heat transfer coefficient between mold cold face and cooling water t mold :mold wall thickness k mold :mold wall heat conductivity t gap :gap between mold hot face and shell surface k gap :gap heat conductivity r contact :contact heat resistance between mold wall and shell surface h rad :heat radiation coefficient between mold hot face and shell surface

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 15 Parameters of Heat Transfer Model Heat Convection Coefficient (W/m 2 K)22,000 (at meniscus) ~ 25,000 (at mold exit) Cooling Water Temperature ( o C)30 (at meniscus) ~ 42 (at mold exit) Water Flow Rate (l/s)4.583 Mold Wall Thickness (mm)6 Mold Wall Conductivity (W/mK)360 Gap Conductivity (W/mK)0.1 Contact Resistance (m 2 K/W)5.6 x  Stefan Boltzman Constant (W/m 2 K 4 ) 5.67 x  m, Mold Wall Surface Emissivity 0.5  s, Steel Surface Emissivity 0.8

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 16 Conditions of 2D Simulation Material Composition (wt%)0.27C, 1.52Mn, 0.34Si, 0.015S, 0.012P Billet Section Size (mm x mm)120x120 Working Mold Length (mm)700 Total Mold Length (mm)800 Taper (%/m)0.75 (on both faces) Time of Turning on Ferrostatic Pressure (sec.)0.3(Run# 3~6), 3.5(Run# 1,2) Mesh Size (mm x mm)0.1x1.0 (at surface), 1.4x1.0 (at center) Node Number7381 Element Number7200 Time Step (sec.)0.001 ~ 0.05 Pouring Temperature ( o C) Solidus Temperature ( o C) Liquidus Temperature ( o C) % Solid Temperature ( o C) (Shell Thickness) % Solid Temperature ( o C) (Damage strain accumulation begins)

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 17 Fully Coupled Simulation corresponding to real mold operation producing hot corner Run # 1 – 2.2m/min Run # 2 – 4.4 m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 18 Heat Flux Predicted V = 2.2 m/min V = 4.4 m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 19 Surface Temperature History V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 20 Shell Thickness History V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 21 Temperature Contour and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 22 Stress along Z dir. and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 23 Stress along Z dir. and Distorted Shape (100mm Below Mold Exit) V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 24 Simulation with uniform heat flux around perimeter corresponding to ideal mold operation (no air gap) producing cold corner Run # 3 – 2.2m/min Run # 4 – 4.4 m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 25 Surface Temperature History V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 26 Shell Thickness History V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 27 Temperature Contour and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 28 Stress along Z dir. and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 29 Stress along Z dir. and Distorted Shape (100mm Below Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 30 Simulation with uniform temperature around perimeter corresponding producing uniform corner Run # 5 – 2.2m/min Run # 6 – 4.4 m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 31 Surface Temperature History V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 32 Shell Thickness History V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 33 Temperature Contour and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 34 Stress along Z dir. and Distorted Shape (Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 35 Stress along Z dir. and Distorted Shape (100mm Below Mold Exit) V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 36 Observations Mold operation resulting hotter corners in the mold leads to hot and weak corner which could not withstand the shell bending around corner due to ferrostatic pressure as the billet is out of the mold. As simulation predicted, billet fails at 4.4m/min casting speed. Mold operation producing uniform or cold corner could support the ferrostatic pressure after mold exit without much bulging. Hot and uniform corners suffer overcooling in spray zones due to 2D heat convection near the corner. This leads to substantial tensile stress along casting direction which might cause transverse corner cracks at surface. Cold corner formed in the mold produces large tensile stress along the casting direction around corner region which might lead to transverse corner cracks in mold. Mold operation resulting hotter corners in the mold leads to hot and weak corner which could not withstand the shell bending around corner due to ferrostatic pressure as the billet is out of the mold. As simulation predicted, billet fails at 4.4m/min casting speed. Mold operation producing uniform or cold corner could support the ferrostatic pressure after mold exit without much bulging. Hot and uniform corners suffer overcooling in spray zones due to 2D heat convection near the corner. This leads to substantial tensile stress along casting direction which might cause transverse corner cracks at surface. Cold corner formed in the mold produces large tensile stress along the casting direction around corner region which might lead to transverse corner cracks in mold.

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 37 Surface Temperature Profiles V=2.2m/min 100mm Below Mold Exit Mold Exit

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 38 Surface Temperature Profiles V=4.4m/min 100mm Below Mold Exit Mold Exit

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 39 Stress Histories at Corner (Fully Coupled Simulation in Mold) V = 2.2 m/min V = 4.4 m/min fully coupled cases 1,2

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 40 Stress Histories at Corner (Uniform Heat Flux around Perimeter in Mold ) V = 2.2 m/min V = 4.4 m/min uniform heat flux cases 3,4

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 41 Stress Histories at Corner (Uniform Temperature around Perimeter in Mold) V = 2.2 m/min V = 4.4 m/min uniform temperature cases 5,6

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 42 Observations The hot and uniform corner formed in the mold suffer overcooling in the spray zones leading to tensile stress near corner surface. The absolute value stress does not depend on casting speed, but on the amount of temperature decreasing. Cold corner suffer reheating in the spray region which will increase the tensile stress already built up at sub surface in the mold and lead to sub-surface transverse cracks. The uniform surface temperature corner is more preferable to prevent either extreme cold or hot corner. Spray pattern should also be designed in care to prevent severe reheating or overcooling near corner. Slice domain model is favorable for ideal taper prediction since it provides results close to 2D prediction having uniform surface temperature around perimeter with much lesser computational cost. The hot and uniform corner formed in the mold suffer overcooling in the spray zones leading to tensile stress near corner surface. The absolute value stress does not depend on casting speed, but on the amount of temperature decreasing. Cold corner suffer reheating in the spray region which will increase the tensile stress already built up at sub surface in the mold and lead to sub-surface transverse cracks. The uniform surface temperature corner is more preferable to prevent either extreme cold or hot corner. Spray pattern should also be designed in care to prevent severe reheating or overcooling near corner. Slice domain model is favorable for ideal taper prediction since it provides results close to 2D prediction having uniform surface temperature around perimeter with much lesser computational cost.

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 43 Shrinkage Predicted by 2D Model V=2.2m/min V=4.4m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 44 Surface Displacement at Mold Exit V=2.2m/min V=4.4m/min

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 45 Shrinkage Predicted by Slice Model

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 46 Shrinkage vs. Casting Speed

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 47 Shrinkage vs. Average Heat Flux

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 48 Mold Distortion vs. Average Heat Flux * Positive mold distortion means negative taper

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 49 Conclusions Optimal mold taper should be able to prevent either very hot or very cold corner region in the mold to avoid the possibility of excessive bulging and transverse surface or subsurface corner cracks. 2D thermal stress analysis with slice domain is preferable for ideal taper investigation. Lesser amount of mold taper is needed when the casting speed is increased or the total amount of heat extracted by mold is decreased. Optimal mold taper should be able to prevent either very hot or very cold corner region in the mold to avoid the possibility of excessive bulging and transverse surface or subsurface corner cracks. 2D thermal stress analysis with slice domain is preferable for ideal taper investigation. Lesser amount of mold taper is needed when the casting speed is increased or the total amount of heat extracted by mold is decreased.

University of Illinois at Urbana-Champaign Metals Processing Simulation Lab Chunsheng Li 50 Future Work Further investigate the shell behavior in more realistic spray pattern. Predict mold shape needed to produce uniform surface temperature around perimeter. More advanced computational techniques to increase simulation speed and accuracy, such as parallel computation. Further investigate the shell behavior in more realistic spray pattern. Predict mold shape needed to produce uniform surface temperature around perimeter. More advanced computational techniques to increase simulation speed and accuracy, such as parallel computation.