Donning and Doffing SCBA Firefighter I

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Copyright and Terms of Service Copyright © Texas Education Agency, These materials are copyrighted © and trademarked ™ as the property of the Texas Education Agency (TEA) and may not be reproduced without the express written permission of TEA, except under the following conditions: 1) Texas public school districts, charter schools, and Education Service Centers may reproduce and use copies of the Materials and Related Materials for the districts’ and schools’ educational use without obtaining permission from TEA. 2) Residents of the state of Texas may reproduce and use copies of the Materials and Related Materials for individual personal use only, without obtaining written permission of TEA. 3) Any portion reproduced must be reproduced in its entirety and remain unedited, unaltered and unchanged in any way. 4) No monetary charge can be made for the reproduced materials or any document containing them; however, a reasonable charge to cover only the cost of reproduction and distribution may be charged. Private entities or persons located in Texas that are not Texas public school districts, Texas Education Service Centers, or Texas charter schools or any entity, whether public or private, educational or non-educational, located outside the state of Texas MUST obtain written approval from TEA and will be required to enter into a license agreement that may involve the payment of a licensing fee or a royalty. Contact TEA Copyrights with any questions you may have.TEA Copyrights 2

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning and Doffing SCBA Most common methods (IFSTA, 2008) – The over-the-head method – The coat method – Donning from a seat – Donning from rear mount or compartment mount The wearer should follow the manufacturer’s instructions and local standard operating procedures (SOPs) for donning his or her specific SCBA unit 3

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning and Doffing SCBA (continued) SCBA checks to complete at shift change or prior to donning the unit include: – Check the air cylinder gauge to ensure that it is full National Fire Protection Association (NFPA) 1404: Standard for Fire Service Respiratory Protection Training NFPA 1404 Standard recommends that a minimum of 90% of the cylinder’s rated capacity is a full cylinder – Check the remote gauge and the cylinder gauge Ensure that the gauges read within 100 psi of the same pressure Ensure that gauges not marked in increments of 100 psi are the same 4

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning and Doffing SCBA (continued) SCBA checks to complete at shift change or prior to donning the unit include: (continued) – Check the harness assembly and the facepiece to ensure that all of the straps are fully extended – Operate all the valves Ensure that they operate properly Ensure that they are in the correct position – Check the personal alert safety system (PASS) device manually for proper operation 5

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning and Doffing SCBA (continued) Donning SCBA from a storage case or apparatus compartment – The specific SCBA manufacturer’s recommendations for donning and use of the SCBA should always be followed – Over-the-head method – Coat method 6

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Over-the-head Method Position the SCBA with the valve end of the cylinder away from the user Open the cylinder valve fully Check the cylinder and the remote pressure gauges – Pressure readings must be within 100 psi – Needles on both gauges indicate the same pressure for gauges without 100 psi increments Raise the SCBA overhead while guiding your elbows into the loops formed by the shoulder straps 7

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Over-the-head Method (continued) Release the harness assembly and allow the SCBA to slide down your back Fasten the chest strap, buckle the waist strap, and adjust the shoulder straps Don the facepiece and check the facepiece seal Connect the air supply to facepiece Activate the PASS device if it is not integrated in the system Don the hood, the helmet, and the gloves 8

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Coat Method Position the SCBA with the valve end of the cylinder away from the user Open the cylinder valve fully Check the cylinder and the remote pressure gauges – Pressure readings must be within 100 psi – Needles on both gauges indicate the same pressure for gauges without 100 psi increments Grasp the top of the left shoulder strap on the SCBA with your left hand and raise the SCBA overhead Guide your left elbow through the loop formed by the left shoulder strap and swing the SCBA around your left shoulder 9

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Coat Method (continued) Guide your right arm through the loop formed by the right shoulder strap allowing the SCBA to come to rest in the proper position Fasten the chest strap, the buckle waist strap, and adjust the shoulder straps Don the facepiece and check the facepiece seal Connect the air supply to the facepiece Activate the PASS device if it is not integrated in the system Don the hood, the helmet, and the gloves 10

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning Seat-mounted SCBA Firefighters can don SCBA while en route to an incident It must be performed safely without the firefighter unbuckling his or her seatbelt Three main types of seat-mounting hardware are – Lever clamp – Spring clamp – Flat hook Facepiece should be in a quick-opening bag to protect it from dust and scratches Do not keep the facepiece connected to the regulator during storage – These parts must be separate in order to check for a proper facepiece seal 11

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning Seat-mounted SCBA (continued) Procedure to don seat-mounted SCBA – Open the cylinder valve fully – Check the cylinder and the remote gauge readings Pressure readings must be within 100 psi Needles on both gauges indicate the same pressure for gauges without 100 psi increments – Position your body in the seat with your back firmly against the SCBA and release the SCBA hold-down device – Insert your arms through the shoulder straps – Fasten the chest straps, buckle the waist strap, and adjust the shoulder straps 12

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning Seat-mounted SCBA (continued) Procedure to don seat-mounted SCBA (continued) – Fasten your seat belt before the apparatus moves – Don the facepiece and check the facepiece seal – Connect the air supply to the facepiece when you are ready to use it – Activate the PASS device manually if it is not integrated in the system – Don the hood, the helmet, and the gloves Exit the fire apparatus carefully to avoid slips or falls due to the extra weight on your back 13

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning SCBA from a Side or Rear Mount Takes more time than the seat-mounted SCBA Reduces the chances of slips and falls Saves time compared to SCBA stored in the carrying case due to the elimination of the following steps – Removing the equipment case from the fire apparatus – Placing it on the ground – Opening the case – Picking up the unit to don Because these units are exposed to weather and physical damage, waterproof covers are desirable Donning steps are similar to seat-mounted units because firefighters only have to back into them 14

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning from a Compartment or a Back-up Mount Compartment mounts present the same advantages as side or rear-mounted units Some disadvantages – Some compartments are too high to back into – Some compartment doors may interfere with donning Back-up mounts provide quick access to SCBA If back-up mounts are too high, they need to be removed and donned using the over-the-head method or the coat method Back-up units at the right height can be donned similarly to the seat-mounted units 15

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning the Facepiece Important differences between facepieces – Some use a rubber harness with adjusting straps – Some use a mesh skullcap with adjusting straps – Some have a different number of adjusting straps – The regulator may attach in different ways May attach to the facepiece May be mounted on the waist belt Interchanging facepieces, or any other part of the SCBA, from one manufacturer’s equipment to another voids any warranty and certification (IFSTA, 2008) NFPA 1500 requires that each firefighter be fitted with a facepiece that conforms properly to the shape and size of his or her face 16

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning the Facepiece: General Considerations Ensure that no hair comes between your skin and the sealing surface of the facepiece Place your chin in the center of the chin cup and center the harness at the back of your head Tighten the facepiece straps by pulling them evenly and simultaneously – Remember that pulling the straps outward may damage them – Tighten the straps in this order The lower straps The temple straps The top strap (if present) 17

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning the Facepiece: General Considerations (continued) Check the facepiece for proper seal and operation – Ensure that the exhalation valve is functioning properly – Ensure that all connections are secure – Ensure that the donning mode switch (if present) is in the proper position 18

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning the Facepiece: General Considerations (continued) Check the positive pressure by gently breaking the facepiece seal – Insert two fingers under the edge of the facepiece – Confirm that you feel air moving past your fingers – If you cannot feel air movement, remove the unit from service and tag it for repair 19

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Donning the Facepiece: General Considerations (continued) Wear the hood over the facepiece harness or straps – All exposed skin must be covered – Vision must not be obstructed Wear the helmet with the chin strap secured 20

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Doffing SCBA Doffing techniques differ for different types of SCBA Actions that apply to all SCBA when doffing – Doffing SCBA Remove the backpack assembly while protecting the regulator – Close the cylinder valve – Relieve pressure from the regulator in accordance with the manufacturer’s instructions – Extend all of the straps – Refill or replace the cylinder – Clean and disinfect the facepiece 21

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Doffing SCBA Skill (IFSTA, 2008) Remove the SCBA Close the cylinder valve completely Bleed air from the high- and low-pressure hoses Check the air cylinder pressure and replace the cylinder if it has less than 90% of rated capacity Return all the straps, valves, and components back to the ready state 22

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Doffing SCBA Skill (IFSTA, 2008) (continued) Inspect the SCBA and facepiece for damage and/or needed cleaning Clean the equipment as needed, remove the damaged equipment from service, and report it to an officer, if applicable Place the SCBA back into the storage area so that it is ready for immediate use 23

Copyright © Texas Education Agency All rights reserved. Images and other multimedia content used with permission. Resources , Essentials of Firefighting and Fire Department Operations (5 th Edition), International Fire Service Training Association (IFSTA),