A System Sensitivity Example Friday 19 Sept 2014 EE 401: Control Systems Analysis and Design Example #2:  Nominally, K = 5 and H = 0.05.  Determine the.

Slides:

Advertisements

Similar presentations

Lecture 15: State Feedback Control: Part I

Advertisements

Feedback loop (CV changes input) SP Controller Gc Plant Gp Sensor Gs E MV (Manipulated Variable CV Controlled Variable +-+- S.

Tutorial 2 Sequential Logic. Registers A register is basically a D Flip-Flop A D Flip Flop has 3 basic ports. D, Q, and Clock.

1 The 2-to-4 decoder is a block which decodes the 2-bit binary inputs and produces four output All but one outputs are zero One output corresponding to.

8255 – PROGRAMMABLE PARALLEL

Slide 1UCSB CMS Weekly Status MeetingCMS 4-Hybrid Test System Sam Burke EE UCSB 4-Hybrid Thermal Test System Status Peltier T/E Element Failures 3 September.

EE 231 Digital Electronics Fall 01 week 1-slide 1 Digital Hardware Systems Digital Systems Digital vs. Analog Waveforms Analog: values vary over a broad.

A common wall between the zones Zone 1 with four walls and four windows Zone 2 with four walls and four windows An example of a model with two zones.

INTRODUCTION TO CONTROL SYSTEMS

Instrumentation (AMME2700) 1 Instrumentation Dr. Xiaofeng Wu.

IASTED PEA 2006, Sept Interzone short wave radiative couplings through windows and large openings : proposal of a simplified model H. Boyer.

High Voltage 8- Channel Board [HV8CB] Vihtori Virta Design Review.

Math – What is a Function? 1. 2 input output function.

4.6 Model Direct Variation

6.376 Final Project: Low-Power CMOS Measurement System for Chemical Sensors Stuart Laval December 8, 2003.

Interpreting Temperature Logger Data

EE 401 Control Systems Analysis and Design

EE 401 Control Systems Analysis and Design Modeling an Electromechanical System The DC Servomotor Friday, Sept. 06, 2013 EE 401: Control Systems Analysis.

S3 INNOVATION ELECTRONICS. LESSON TITLE: ELECTRONICS Learning Intention: To understand when to use different types of logic gates Activity: Building own.

EE 401 Control Systems Analysis and Design Modeling an Electromechanical System The DC Servomotor Fri, Jan 29 EE 401: Control Systems Analysis and Design.

System Level Block Diagram P16318 Lianna Dicke. P16318: Gaseous Mass Flow Rate Controller Level 1 Functional Block Diagram 1.0 System Processing 2.0 Mechanical.

EE 460 Advanced Control and Sys Integration State-Space Realizations Fri, Sept 11 EE 460 Advanced Control and System Integration Slide 1 of 5.

AND Gate Inputs Output Input A (Switch) Input B (Switch) Output Y (Lamp) 0 (Open) 0 (OFF) A B Lamp.

CEC 220 Digital Circuit Design SOP and POS forms Friday, Sept 11 CEC 220 Digital Circuit Design Slide 1 of 17.

EE 460 Advanced Control and Sys Integration Feedback Summary Mon, Oct 26 EE 460 Advanced Control and System Integration Slide 1 of 4.

EE 401 Control Systems Analysis and Design A Review of The Laplace Transform Friday 15 Jan 2016 EE 401: Control Systems Analysis and Design Slide 1 of.

Slide 1 Loss Function Losses begin to accrue as soon as a quality characteristic of a product or service deviates from the nominal value Under the Taguchi.

May 5, 2004Slide 2 OmnAuto TMS Solution May 5, 2004Slide 3 OmnAuto TMS Dataflow.

EE 495 Modern Navigation Systems

Test slide upload.

Chapter 1 Connections to Algebra Review

Control Systems EE 4314 Lecture 12 March 17, 2015

Seeds and Growth in Plants Module (9 pages/slides) SLIDE 1 of 9

continued on next slide

Date of download: 12/26/2017 Copyright © ASME. All rights reserved.

סמים וסינפסות.

Presentation Test. Second Slide Third Slide It worked.

كيفية إعداد دراسة جدوى اقتصادية

A New Control Framework

continued on next slide

continued on next slide

Notes Over 2.1 Function {- 3, - 1, 1, 2 } { 0, 2, 5 }

شاخصهای عملکردی بیمارستان

تحليل الحساسية Sensitive Analysis.

Lecture 4: Discrete-Time Systems

البيئة السياسية للإدارة الدولية

بعض النقاط التي تؤخذ في الحسبان عند تقييم الاستثمارات الزراعية

مدل زنجیره ای در برنامه های سلامت

فرق بین خوب وعالی فقط اندکی تلاش بیشتر است

Modeling in the Time Domain

E190Q – Final Project Presenation

Function Notation “f of x” Input = x Output = f(x) = y.

Transp Course 2014 Overview.

Systems Practice Use the next slide in this powerpoint as a template to identify 10 different types of systems. 4 of your slides need to be natural systems.

Evaluating Logarithms

Exponential and Logarithmic Forms

CONTROL SYSTEM AN INTRODUCTION.

DN OAD Processes: RG 0316 : Offtake Workstream

Habitats 1a 1 Read and Watch the information on the next slide about Habitats. Use the organiser to guide your discoveries and your.

Find the closed-loop transfer function in terms of Gİ.

Control Systems Spring 2016

АВЛИГАТАЙ ТЭМЦЭХ ҮНДЭСНИЙ ХӨТӨЛБӨР /танилцуулга/

Objective- To graph a relationship in a table.

Systems Practice Use the next slide in this powerpoint as a template to identify 5 different types of systems. 2 of your slides need to be natural systems.

continued on next slide

Arithmatic Logic Unit (ALU). ALU Input Data :  A0-A3  B0-B3 Output Data :  F0 – F3.

By: Nafees Ahamad, AP, EECE, Dept. DIT University, Dehradun

continued on next slide

Presentation transcript:

A System Sensitivity Example Friday 19 Sept 2014 EE 401: Control Systems Analysis and Design Example #2:  Nominally, K = 5 and H =  Determine the sensitivity of the system to variations in K and H.  + - Controller Sensor Plant Input Output The System Transfer Function Slide 1 of 3

A System Sensitivity Example Friday 19 Sept 2014 EE 401: Control Systems Analysis and Design Slide 2 of 3

A System Sensitivity Example Friday 19 Sept 2014 EE 401: Control Systems Analysis and Design 2.Sensitivity of T to variations in H o See Mathematica “sensitivity-example.nb”sensitivity-example.nb  Due to high sensitivity of T to H, we should invest in high performance sensor block (H). Slide 3 of 3