Plant Wide Alarm System

Alarm Tones  4 Alarm Tones  General Evacuation – Wail  Severe Weather – Pulsed Steady  Local Alarm – Pulsed Wail  All Clear - Steady  4 Alarm Tones  General Evacuation – Wail  Severe Weather – Pulsed Steady  Local Alarm – Pulsed Wail  All Clear - Steady

Alarm Locations Alarms are located in following locations:  Area 2 (Tag # S-M-301E)  Area 5 (Tag # S-M-301D)  Area 4 (Tag # S-M-301G)  Area 6 South (Tag # S-M-301C)  Dock (Tag # S-M-301H)  North Tank Farm (Tag # S-M-301F) Alarms are located in following locations:  Area 2 (Tag # S-M-301E)  Area 5 (Tag # S-M-301D)  Area 4 (Tag # S-M-301G)  Area 6 South (Tag # S-M-301C)  Dock (Tag # S-M-301H)  North Tank Farm (Tag # S-M-301F)

Area 2 Area 2 Area 5

Area 4 Area 6 South

Dock North Tank Farm

Discrete Alarms  Each alarm location is activated thru a radio frequency  MHz UHF  Alarm Locations are battery powered by Volt Batteries  Batteries are kept charged by solar panels at each location.  Each alarm location is activated thru a radio frequency  MHz UHF  Alarm Locations are battery powered by Volt Batteries  Batteries are kept charged by solar panels at each location.

Alarm Activation Alarm can be activated in 2 locations  Northeast Corner of Central Control Room (Tag # S-M-301A)  SS2000D Encoder, Microphone and Computer  Security Office Administration Building on St. Bernard Hwy. (Tag# S-M-301B)  SS200D Encoder and Microphone only Alarm can be activated in 2 locations  Northeast Corner of Central Control Room (Tag # S-M-301A)  SS2000D Encoder, Microphone and Computer  Security Office Administration Building on St. Bernard Hwy. (Tag# S-M-301B)  SS200D Encoder and Microphone only

Alarm Activation  When event has been identified  Appropriate alarm is activated by pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control  Warning tones will sound for the pre- programmed period of 3 minutes or until cancelled.  The Microphone can be used for making emergency voice broadcasts  When event has been identified  Appropriate alarm is activated by pressing the pre programmed key sequence on the SS2000D FSK Encoder or the computer in Central Control  Warning tones will sound for the pre- programmed period of 3 minutes or until cancelled.  The Microphone can be used for making emergency voice broadcasts

Activating via the SS2000D

System Activation 2. Press the Function Button SYSTEM ACTIVATED 1. With Key in, turn Key switch to “ON” 3. Verify function selection 4. Press the “Send” Button

Canceling a Command or an Activation Before a Function has been sent, Press “CLEAR” to Cancel After a Function has been sent, Press “CLEAR” if polling is in progress then press “CANCEL ALL” and press “SEND” CANCEL ALL

SS2000D Alarms and Status Indicators  PRINTER – Indicates when the SS2000 sends information to the printer  CARRIER – RF Channel busy indicator  AUX. – Auxillary use only  KEY – Lights whenever a key on the mylar keypad is depressed  PRINTER – Indicates when the SS2000 sends information to the printer  CARRIER – RF Channel busy indicator  AUX. – Auxillary use only  KEY – Lights whenever a key on the mylar keypad is depressed PRINTER CARRIER AUX. KEY

Monitor and Activate via the Computer

Recommended View – Map Screen 1. Click “Map”2. Click “Legend”

Checking for Site Status Click desired Site Click Poll To get an updated Site status Click “Notepad” to create Notes

System Activation 1. Click “Activate”3. Click “OK”2. Click desired Hot Key SYSTEM ACTIVATED

Canceling a Command or an Activation Click “Cancel” before Entry has been sent. Click “Cancel All”, “OK,” after Command has been sent.

“Minimize” Acknowledging an Alarm Click AcknowledgeClick “System Log”

Never Exit the Program

System Monitoring  The PC at the base station in central control continuously monitors the system  The software keeps running log of all events and “Quiet Test” responses  Quiet Tests are performed automatically  Failure of Quiet Test will be indicated on the PC  The PC at the base station in central control continuously monitors the system  The software keeps running log of all events and “Quiet Test” responses  Quiet Tests are performed automatically  Failure of Quiet Test will be indicated on the PC